Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for ABLE Cultisir
- Page 1 Cultistir Magnetic stirrer for cell culture Operating instructions 190924_REV.2...
-
Page 2: Table Of Contents
Contents Safety precautions ....................3 II. Condition of use ....................4 III. Technical data ....................6 Equipment provided ..................8 1. Controller and motor ..................8 2. Base plate ......................10 V. Installation ......................12 1. Assemble ......................12 2. Installation space .................... 12 3. -
Page 3: Safety Precautions
Safety precautions General Throughout the manual, the following symbol will be used to indicate general precautionary measures: Indication: information the correct use of Cultistir Danger: Warning that, if safety precautions are not observed, injury to personnel may result. Warning: Warning that, if safety precautions are not observed, damage may result to the instruments. -
Page 4: Condition Of Use
(e.g. micro carriers). Product combinations Cultistir is designed for using with ABLE single-use bioreactor of 5mL (Product No. BWV-S005A), 30mL (Product No. BWV-S03A), 100mL (Product No. BWV-S10A). Cultistir is not designed for using of any other culture vessel or bioreactor, spinner flask. - Page 5 Cultistir, the supervisor must ensure that no other dangers exist, especially if other instruments and systems are also being used. Changes in configuration/design by user No changes may be made to Cultistir. Any alteration made releases ABLE corporation from any liability for damage caused. Power requirements...
-
Page 6: Technical Data
III. Technical data Item name Controller and motor Product No. DW-1013 Controller Dimensions (W × D × H) 132 × 150 × 41 mm Weight (gross) 0.6kg Power cable length Speed Range (Resolution) 5-120 rpm (1rpm) Power source AC100-240V±10%/50-60Hz/10VA Operating condition 15-45°C/max., 80% RH Altitude of the installation site Use below 2000 m above sea level... - Page 7 Item name 6ch. Base plate for 30/100mL Product No. BWS-S03N0S-6B Dimensions (W × D × H) 153 × 267 × 33 mm Weight (gross) 1.8kg Speed Range 5-120 rpm Stirring position Applicable products BWV-S03A, BWV-S10A Power source − Operating condition 15-45°C/max., 99% RH/max., 10% CO Altitude of the installation site Use below 2000 m above sea level...
-
Page 8: Equipment Provided
IV. Equipment provided Controller and motor Controller and motor (product No. DW-1013) comprises: Controller Motor Power cable Operating instructions Motor Power cable Controller 190924_REV.2... - Page 9 ② ① ③ ④ ③ ⑥ ⑤ ⑦ ⑨ ⑧ ⑩ ⑧ ① Power switch: Switches the instrument on/off ② Stirring button: Switches stirring on/off ③ ▽/△ : Up down keys change stirring speed values (rpm) By keeping keys, values are displayed in rapid ④...
-
Page 10: Base Plate
Base plate 6ch. Base plate for 5mL (Product No. BWS-S005N0S-6A) comprises: 6ch. Base plate for 5mL Fixing screw ① ③ ② ② Fixing screw Base plate ③ ① Reactor set position: 6 position of magnetic drive ② Motor mounting port: Fixing Motor on Base plate ③... - Page 11 6ch. Base plate for 30/100mL (Product No. BWS-S03N0S-6B) comprises: 6ch. Base plate for 30/100mL Fixing screw Attachment ring Attachment ring ① ① ① ① ④ ① ① ③ ② ② Fixing screw ③ Base plate ① Reactor set pin: 6 pins of magnetic drive ②...
-
Page 12: Installation
V. Installation Assemble Fix Motor and Base plate with fixing screws. Controller and Motor is compatible with two types Base plate: 6ch. Base plate for 5mL (Product No. BWS-S005N0S-6A) 6ch. Base plate for 30/100mL (Product No. BWS-S03N0S-6B) NB: When assembling Motor and Base plate or changing a device, must be power off. -
Page 13: Putting Device Into Operation
Putting device into operation ① After cleaning of assembled Base plate and Motor, place into incubator. ② Put motor cable outside from the utility port of incubator. ③ Connect power cable to the power cable port of Controller. Connect motor cable to the rear port of controller. -
Page 14: Operation
VI. Operation Starting (for 5mL) ① Switch the power switch to ON position. ② Stirring speed is displayed on the display. Set the stirring speed with the △/up and ▽/down keys. During the setting, speed indicator on the display panel blinks. ③... -
Page 15: Starting (For 100Ml)
Starting (for 100mL) ① Place the attachment ring on small pins on Base pate surface (3 posion that are not adjacent). Attachment ring ② Switch the power switch to ON position. ③ Stirring speed is displayed on the display. Set the stirring speed with the △/up and ▽/down keys. -
Page 16: Trouble Shooting
VII. Trouble shooting This product is maintenance-free. There are no periodic replacement parts. When any of the following conditions appears, please contact our service. ① If the motor stops due to a failure, the controller issues a continuous beep sound. ②... -
Page 17: Cleaning
VIII. Cleaning Cleaning work To clean the instruments, use a cloth moistened with customary cleansing agents like soapy water, 70 % ethanol solution. DO NOT spray directly on the instrument but use a cloth and wipe dry directly after cleaning. Always switch off the instrument and disconnect it from power supply when carrying out cleaning work. -
Page 18: Guarantee
X. Manufacturer and service contacts Manufacturer: ABLE Corporation Tokyo, Japan http://able-biott.co.jp/en/ Customer service: Please contact your local distributor of ABLE products. To find out name and address of your local distributor go to ABLE web site and inquire us. http://able-biott.co.jp/en/contact/ 190924_REV.2... - Page 19 Document No:S-1475-DoC Date of issue on : August 30, 2019 EU Declaration of Conformity We ABLE Corporation 7-9, Nishigoken-cho, Shinjyuku-ku, Tokyo, 162-0812, Japan declares under our sole responsibility that the product described below in compliance with the following directive Hereby declares that the product described below: CULTISTIR（カルチスター）...
- Page 20 © 2019 ABLE Corporation All rights to this documentation are reserved. 190924_REV.2...
Need help?
Do you have a question about the Cultisir and is the answer not in the manual?
Questions and answers