Related Manuals for Whitehall E-27-S
Summary of Contents for Whitehall E-27-S
- Page 1 INSTRUCTIONS FOR OPERATION AND CARE OF (Stationary Whirlpool) E-27-S S-90-S Member of 6900-194-000 Revised: February 2016...
- Page 2 European Union CE Mark The presence of the CE Mark on Whitehall equipment means that it has been designed, tested and certified as complying with all applicable European Union regulations and recommendations. Waste Electrical and Electronic Equipment (WEEE) This s ymbol on the product or on its packaging indicates that this product must not be disposed of with regular waste.
-
Page 3: Table Of Contents
Table of Contents Warning ..............................Page a Table of Contents ..........................Page 1 General Knowledge..........................Page 2 Operating Skills & Training ......................Page 2 Patient Evaluation ........................Page 2 Inspecting Whirlpool ........................Page 2 Using The Whirlpool ..........................Page 3 Installation & Operation ........................Pages 4-8 Fixture Installation Location Guide....................Page 4 Stationary Style Hydrotherapy Whirlpool Dimensions..............Page 5 Combined Drain / Overflow ......................Page 6 Separate Drain / Overflow......................Page 7... -
Page 4: Warning
INSPECTING THE WHIRLPOOL This Whitehall product has been carefully packaged at the Inspection Checklist factory to minimize the possibility of damage during shipping. -
Page 5: Using The Whirlpool
Installing the Whirlpool, page 4. A rough-in drawing is available to assist the installer. Contact Whitehall Customer Service, bottom of page, for additional installation not covered in this manual. Ÿ Confirm that the whirlpool operates properly. See Inspecting the Whirlpool , page 2. -
Page 6: Installation & Operation
(1327) ELECTRICAL REQUIREMENTS: 8 AMPS, 115 VOLTS. 2" COMBINATION DRAIN AND OVERFLOW ASSEMBLY AT WALL PROVIDE ONE 3 POLE RECEPTACLE HOSPITAL FURNISHED BY WHITEHALL GRADE WITH GROUND FAULT INTERRUPT FOR TURBINE OVER RIM INLET ASSEMBLY HOT & COLD WATER INLET THERMOSTATIC MIXING VALVES ARE OPTIONAL 2"... -
Page 7: Stationary Style Hydrotherapy Whirlpool Dimensions
28/711 15/381 18/457 24/610 26/660 26.5/673 1/2" or 3/4" IPS E-22-SP 28/711 15/381 18/457 34/864 20/508 26.5/673 1/2" or 3/4" IPS E-27-S 28/711 15/381 21/533 27/686 26/660 26.5/673 1/2" or 3/4" IPS E-36-S 28/711 15/381 25/635 32/813 26/660 26.5/673 1/2" or 3/4" IPS... -
Page 8: Combined Drain / Overflow
Installation Instructions 4 " NOTE: THESE INSTALLATION 1" INSTRUCTIONS ARE USED FOR ALL WHITEHALL OR DAKON STATIONARY ALL MODELS. 5" REFERENCE DRAWINGS ASSEMBLIES PAGE NUMBER 2 1 4 " MOTOR/TURBINE RAISING/LOWERING/SM DETAIL "A" RAISING/LOWERING (TOP VIEW) DRAIN OVERFLOW E DRAIN OVERFLOW H/S... -
Page 9: Separate Drain / Overflow
Installation Instructions; -SDO Separate Drain Overflow Installation Instructions; -SDO Separate Drain Overflow 4 " 1" NOTE: THESE INSTALLATION INSTRUCTIONS ARE USED FOR ALL WHITEHALL OR DAKON ALL STATIONARY -SDO MODELS. REFERENCE DRAWINGS ASSEMBLIES PAGE NUMBER 7 7 8 " MOTOR/TURBINE... -
Page 10: Slant Back
Installation Instructions; Slant Back REFERENCE DRAWINGS ASSEMBLIES PAGE NUMBER MOTOR/TURBINE RAISING/LOWERING DRAIN OVERFLOW THERMOMETER 12 1 8 " 6 7 8 " 1 1 4 " TYP. 17" TYP. DETAIL "A" (TOP VIEW) ASSEMBLY PROCEDURE: ROUGH-IN FOR 2" OD DRAIN LINE 1 AND WATER INLET VALVE. (SEE DETAIL A) NOTE: FOR INFORMATION ON OPTIONAL THERMOSTATIC MIXING VALVE CONTACT FACTORY. -
Page 11: Repair Parts
Stationary Motor/Turbine Assembly THESE REPAIR PARTS ARE USED FOR THE FOLLOWING MODEL NUMBERS ONLY: 14 15 WHITEHALL MODEL DAKON WHITEHALL MODEL DAKON NUMBERS MODEL NUMBERS NUMBERS MODEL NUMBERS E-15-M-SDP DD-2516 L-75-M-SDP E-15-S DF-2516 L-75-S E-22-M-SDP DD-2818 L-90-M-SDP DD-6018 E-22-S DF-2818... -
Page 12: Stationary "E" Series
IMPELLER SHAFT - 26-3/8" - E-45 6525-528-001 PLUNGER ASSY - 15-1/4" - E-22-S 6509-110-199 IMPELLER TUBE - 15-1/4" - E-15 6525-531-001 PLUNGER ASSY - 16-1/2" - E-27-S 6509-115-199 IMPELLER TUBE - 18-1/4" - E-22 6525-535-001 PLUNGER ASSY - 20" - E-45-S 6509-120-199 IMPELLER TUBE - 21-1/4"... -
Page 13: Stationary "H" Series
Stationary “H” Series Parts Diagram THESE REPAIR PARTS ARE USED FOR THE FOLLOWING MODEL NUMBERS ONLY: WHITEHALL MODEL DAKON NUMBERS MODEL NUMBERS H-60-M-SDP DD-3628 H-60-S DF-3628 H-75-M-SDP H-75-S H-90-M-SDP H-90-S H-105-M-SDP DD-4828 H-105-S DF-4828 * NOTE: SEE ADDITIONAL DRAWING FOR DETAIL OF ITEMS NOT SHOWN. -
Page 14: Stationary "L" Series
Stationary “L” Series Parts Diagram THESE REPAIR PARTS ARE USED FOR THE FOLLOWING MODEL NUMBERS ONLY: WHITEHALL MODEL DAKON NUMBERS MODEL NUMBERS L-75-M-SDP L-75-S L-90-M-SDP DD-6018 L-90-S DF-6018 L-105-M-SDP DD-6618 L-105-S DF-6618 * NOTE: SEE ADDITIONAL DRAWING FOR DETAIL OF ITEMS NOT SHOWN. -
Page 15: Stationary "P" Series
Stationary “P” Series Parts Diagram THESE REPAIR PARTS ARE USED FOR THE FOLLOWING MODEL NUMBERS ONLY: WHITEHALL MODEL DAKON NUMBERS MODEL NUMBERS P-10-M-SDP P-10-S P-15-M-SDP DD-2516 P-15-S DF-2516 P-22-M-SDP DD-2818 P-22-S DF-2818 NOTE: SEE ADDITIONAL DRAWING FOR DETAIL OF ITEMS NOT SHOWN. -
Page 16: Stationary "S" Series
Stationary “S” Series Parts Diagram THESE REPAIR PARTS ARE USED FOR THE FOLLOWING MODEL NUMBERS ONLY: WHITEHALL MODEL DAKON NUMBERS MODEL NUMBERS S-85-M-SDP S-85-S DFT-4825 S-90-M-SDP S-90-S S-110-M-SDP S-110-S DFT-5625 NOTE: SEE ADDITIONAL DRAWING FOR DETAIL OF ITEMS NOT SHOWN. -
Page 17: Motor Raising & Lowering Assembly (Small)
Motor Raising & Lowering Assembly (Small) THESE REPAIR PARTS ARE USED FOR THE FOLLOWING MODEL NUMBERS ONLY: WHITEHALL DAKON MODEL MODEL NUMBERS NUMBERS E-15-S DF-2516 E-22-MU E-22-S DF-2818 E-22-SP P-10-S P-15-S DF-2516 P-22-S DF-2818 R & L ASSY P-10-S R & L ASSY P/E-15-S R &... -
Page 18: Motor Raising & Lowering Assembly
R & L ASSY L-75/90/105-S ITEM PART NUMBER DESCRIPTION ITEM PART NUMBER DESCRIPTION 6530-220-001 1" DIA. R & L ASSY - E-27-S 6503-075-000 1-1/8" x 34" SPRING - H-60/75/90/105-S 6530-235-001 1" DIA. R & L ASSY - E-45/S-85/90/110-S 6503-060-000 1-3/8" x 23-1/2" SPRING - L-75/90/105-S 6530-245-001 1"... -
Page 19: Motor Raising & Lowering Assembly (Slant Back)
Motor Raising & Lowering Assembly (Slant Back) SCALED x 1-1/2 ITEM PART NUMBER DESCRIPTION ITEM PART NUMBER DESCRIPTION 6530-260-001 R & L ASSEMBLY 0116-104-000 1/4"-20 x 1/2" PHILLIPS ROUND HEAD SCREW 6502-401-000 1/4"-20 x 5/16 SET SCREW 6530-310-199 END CAP 6530-411-199 LOCKING HUB 6530-520-000... -
Page 20: Drain / Overflow Assembly - H/S Series
Drain / Overflow Assembly - H/S Series 28 29 1A 1B 1C 1D 1E 1F ITEM PART NUMBER DESCRIPTION ITEM PART NUMBER DESCRIPTION 6531-010-001 DRAIN & OVERFLOW - H-60-S 6502-450-000 #8-32 x 3/8" PHILLIPS PAN HEAD SCREW 6531-012-001 DRAIN & OVERFLOW - H-75-S 6531-110-001 FRICTION LOCK ASSEMBLY 6531-011-001... -
Page 21: Drain /Overflow Assembly - "E" Series
6509-305-199 2" O.D. x 7-3/8" DRAIN TUBE - E-22-SP 6502-200-000 1/4"-20 x 5/8" PHILLIPS TRUSS HEAD SCREW 6509-325-199 2" O.D. x 13-3/4" DRAIN TUBE - E-27-S 6502-520-000 1/4"-20 ACORN NUT 6509-335-199 2" O.D. x 15-1/2" DRAIN TUBE - E-45-S 6509-405-199 2"... -
Page 22: Drain / Overflow Assembly - Lo-Boy
Drain / Overflow Assembly - Lo-Boy 1A 1B 1C ITEM PART NUMBER DESCRIPTION ITEM PART NUMBER DESCRIPTION 6531-024-001 DRAIN & OVERFLOW ASSEMBLY - L-75-S 6531-100-199 OVERFLOW BRACE 6531-023-001 DRAIN & OVERFLOW ASSEMBLY - L-90-S 0337-050-000 1/4" HELICAL STAINLESS STEEL LOCKWASHER 6531-022-001 DRAIN &... -
Page 23: Drain / Overflow Assembly - Podiatry Series
Drain / Overflow Assembly - Podiatry Series 1A 1B 1C ITEM PART NUMBER DESCRIPTION ITEM PART NUMBER DESCRIPTION 6531-021-001 DRAIN & OVERFLOW ASSEMBLY - P-10-S 6531-100-199 OVERFLOW BRACE 6531-020-001 DRAIN & OVERFLOW ASSEMBLY - E/P-15-S 0337-050-000 1/4" STAINLESS STEEL HELICAL LOCKWASHER 6531-019-001 DRAIN &... -
Page 24: Drain / Overflow Assembly - Slant Back
Drain / Overflow Assembly - Slant Back 16 15 SCALED x 1-1/4 ITEM PART NUMBER DESCRIPTION ITEM PART NUMBER DESCRIPTION WHR00050-001 DRAIN & OVERFLOW ASSEMBLY WHR00057-199 GROMMET GUIDE NUT 6508-000-199 DRAIN ELBOW 6531-110-199 FRICTION LOCK HOUSING 6504-500-000 DRAIN GASKET 6531-111-199 FRICTION LOCK ROD 6508-050-199 STRAINER... -
Page 25: Separate Drain / Overflow Assembly - P-10, P/E-15/22
Separate Drain / Overflow Assembly - P-10, P/E-15/22 1B 1C ITEM PART NUMBER DESCRIPTION ITEM PART NUMBER DESCRIPTION 6531-200-001 SEPARATE DRAIN OVERFLOW - P-10-S 6531-330-000 STRAINER ASSY - FOR -SDO & BURN TANKS 6531-205-001 SEPARATE DRAIN OVERFLOW - P/E-15-S 6531-331-199 LOCK RING 6531-210-001 SEPARATE DRAIN OVERFLOW - P/E-22-S... -
Page 26: Separate Drain / Overflow Assembly - E-22-Sp
2" O.D. x 6-5/8" DRAIN TUBE - E-22-SP 6509-338-199 2" O.D. x 15-1/2" DRAIN TUBE - E-22-SP 6531-405-199 2" O.D. x 12-3/8" DRAIN TUBE - E-27-S 6509-348-199 2" O.D. x 18-1/8" DRAIN TUBE - E-27-S 6531-331-199 2" O.D. x 14-1/4" DRAIN TUBE - E-45-S 6509-363-199 2"... -
Page 27: Separate Drain / Overflow Assembly - H60/70/90, S85/90
Separate Drain / Overflow Assembly - H60/70/90, S85/90 1D 1E 5C 5D ITEM PART NUMBER DESCRIPTION ITEM PART NUMBER DESCRIPTION 6531-230-001 SEPARATE DRAIN OVERFLOW - H-60-S 6509-605-199 DRAIN ROD - H-60/75/90-S 6531-235-001 SEPARATE DRAIN OVERFLOW - H-75-S 6509-604-199 DRAIN ROD - S-85/90-S 6531-250-001 SEPARATE DRAIN OVERFLOW - H-90-S 6531-330-000... -
Page 28: Butterfly Drain Valve
Drain Valve Assembly DRAIN VALVE ASSEMBLY ITEM PART NUMBER DESCRIPTION ITEM PART NUMBER DESCRIPTION 6531-325-001 DRAIN VALVE ASSEMBLY 6502-402-000 5/16"-18 x 1/4" HEX SOCKET SET SCREW 6531-321-001 DRAIN VALVE FLANGE - MALE ASSEMBLY 6531-320-199 DRAIN VALVE FLANGE - FEMALE 6502-143-000 5/16"-18 x 2-1/4"... -
Page 29: Thermometers
Thermometer NOTE: THE THERMOMETER GAUGES TEMPERATURES FROM 40° TO 140° F. DO NOT ALLOW TEMPERATURES TO EXCEED 140° TO AVOID DAMAGING THE THERMOMETER. TO RECALIBRATE: IMMERSE THE STEM A MINIMUM OF 4” INTO THE WATER TURN ON THE TURBINE ASSEMBLY AND ANOTHER ACCURATE TEMPERATURE GAUGE TO COMPARE AND USE THE EXTERNAL ADJUSTMENT SCREW PROVIDED ON THE THERMOMETER CASING AS INDICATED a . -
Page 30: Cleaning & Disinfecting
8. Fill the bucket with water and run turbine for five seconds to rinse impeller cavity. *Whitehall recommends the use of Hydrochlor® Whirlpool Antiseptic with all patient treatments. This simplifies cleaning of equipment by eliminating need for repeated rinsing and scrubbing. -
Page 31: Care & Cleaning
To remove rust stains: THINGS TO AVOID Wipe surfaces with CRES (available through Whitehall) or Ÿ Harsh polishing cleanser (Comet, Bon Ami, etc.) equivalent cleaner. Use recommended solutions. Apply Ÿ... -
Page 32: Maintenance & Troubleshooting
MSDS, Material Safety Data Sheets. You can purchase a recommended disinfectant from Whitehall Customer Motor does not start when switch is turned on: Service (Back of Manual) or your Whitehall distributor. Ÿ Check your power source. Have a qualified technician check switch. -
Page 33: Motor Information
Motor Information MOTOR DISASSEMBLY Motor Cover Waterproof Toggle Switch Cover Switch Motor Wire Connector Assemblies Motor Base Power Cord Capacitor Assembly Condenser Cover SWITCH WIRING (115V) SWITCH WIRING (230V) SWITCH SWITCH POWER INLET POWER INLET MOTOR MOTOR YEL/GRN YEL/GRN... - Page 34 Whitehall Manufacturing Company warrants that its products are free from defects in material or workmanship under normal use and service for a period of one year from date of shipment. Whitehall's liability under this warranty shall be discharged solely by replacement or repair of defective material, provided Whitehall is notified in writing within one year from date of shipment, F.O.B.