Summary of Contents for ICP Service Unit iMAT 33
- Page 1 EN-US - english US Instructions for installation and operation Replacement unit SERVICE UNIT ¡MAT 33...
- Page 2 Service Unit iMAT 33...
-
Page 3: Table Of Contents
Pictograms and symbols ........................4 Safety instructions ..........................4 Technical data ............................6 Control and maintenance ........................7 Elements and components........................13 Recommended spare parts........................14 Service Unit iMAT 33... -
Page 4: Pictograms And Symbols
Make sure that persons or objects cannot be hit by condensate or escaping compressed air. Pos : 10 /Beko T ec hnis che D okumentati on/Sic her hei t/Gefahr Netzs pannung 1 s/w @ 0\mod_1184148186948_15098.doc x @ 15122 @ @ 1 Service Unit iMAT 33... - Page 5 Exact compliance with the installation- and operation instructions in this manual • Regular maintenance and control of the iMAT in accordance with the instructions in this operating manual Pos : 16 /---- Seitenumbr uch ---- @ 0\mod_1157028099015_0.doc x @ 15320 @ @ 1 Service Unit iMAT 33...
-
Page 6: Technical Data
G ½ Ø 13 mm hose connector Condensate oil-contaminated + oil-free Housing aluminium + plastic, glass fibre-reinforced Weight (empty) 0,78 kg (1.71 lbs) Pos : 19 /---- Seitenumbr uch ---- @ 0\mod_1157028099015_0.doc x @ 15320 @ @ 1 Service Unit iMAT 33... -
Page 7: Control And Maintenance
(see "Proper use" section) • Exact compliance with the installation- and operation instructions in this manual • Regular maintenance and control of the iMAT in accordance with the instructions in this operating manual Service Unit iMAT 33... - Page 8 (22) and remove the service unit (9) by slightly pulling and lifting it. 5. Remove the design shell (11) using a screwdriver. 6. Unscrew the four cover screws (16) and remove the cover (17). 7. Clean the condensate receiver tank (19). Service Unit iMAT 33...
- Page 9 8. Insert new cover O-ring (18) gasket kit) according to the diagram. 9. Clean the sealing surfaces of the cover. 10.Put on the cover (17) with the new O-ring and carefully tighten the four cover screws (16) crosswise (8 Nm). Service Unit iMAT 33...
- Page 10 Control and maintenance 11.Clean the sealing surfaces (←) at the condensate receiver tank (19). Service Unit iMAT 33...
- Page 11 15.Mount the service unit along with the design shell at the condensate receiver tank (19) and tighten both cross recessed head screws (22) (2,5 Nm). 16.Re-install the iMAT at the inlet tubing and outlet, in reverse order to disassembly. Service Unit iMAT 33...
- Page 12 • Check of the electrical connections • Check of the correct engagement of the control unit Pos : 29 /---- Seitenumbr uch ---- @ 0\mod_1157028099015_0.doc x @ 15320 @ @ 1 Service Unit iMAT 33...
-
Page 13: Elements And Components
22 Cross recessed head screw M6 x 16 11 Design shell 24 Cord packing (only previous version) 12 O-ring 8 x 4 27 Deflector plate (only) Pos : 32 /---- Seitenumbr uch ---- @ 0\mod_1157028099015_0.doc x @ 15320 @ @ 1 Service Unit iMAT 33... -
Page 14: Recommended Spare Parts
Pos : 34 /Beko T ec hnis che D okumentati on/Ers atzteile Verbr auchs materialien Zubehör/BEKOMAT/Ers atz teil e IC P 33 (BM 33U USA F KM) @ 9\mod_1415113912256_15098.doc x @ 42505 @ @ 1 Available sets of spare parts Contents Order number Service Unit iMAT 33 8, 9, 12, 13 4028459-ICP Gasket kit... - Page 15 Spare parts 5, 14 Lower part of the cover 13 Symbole 4 Maintenance 7 Technical data 6 Maintenance including the cleaning of the condensate receiver tank 8 Upper part of the cover 13 Order number 14 Service Unit iMAT 33...
- Page 16 Independent Compressor Partners, LLC P.O. Box 206 Jeffersonville, IN 47131 www. compressorpartners.com Translation of the original manual/instructions. Original instructions are in German Subject to technical modifications without notice / errors accepted. ICP_iMAT33_Service_Unit_en_us_2014_12. Printed in Germany Service Unit iMAT 33...