Advertisement
Quick Links
SETHCO
Thermoplastic Pumps
A Met-Pro Fluid Handling Technologies Company
O O
P P
E E
R R
T T
I I
N N
G G
I I
N N
S S
T T
R R
U U
C C
T T
I I
O O
N N
S S
O O
P P
E E
R R
T T
I I
N N
G G
I I
N N
S S
T T
R R
U U
C C
T T
I I
O O
N N
S S
Z Z
K K
X X
3 3
/ /
4 4
C C
S S
Z Z
K K
X X
3 3
/ /
4 4
C C
S S
Sethco
800 Emlen Way, Telford, PA 18969
Tel:
Fax:
215-799-2577 •
215-799-0920
w w w w w w . . s s e e t t h h c c o o . . c c o o m m • • i i n n f f o o @ @ s s e e t t h h c c o o . . c c o o m m
Advertisement
Related Manuals for Sethco ZKX 3/4CS
Summary of Contents for Sethco ZKX 3/4CS
- Page 1 SETHCO Thermoplastic Pumps A Met-Pro Fluid Handling Technologies Company Sethco 800 Emlen Way, Telford, PA 18969 Tel: Fax: 215-799-2577 • 215-799-0920 w w w w w w . . s s e e t t h h c c o o . . c c o o m m • • i i n n f f o o @ @ s s e e t t h h c c o o . . c c o o m m...
- Page 2 SETHCO Thermoplastic Pumps A Met-Pro Fluid Handling Technologies Company INDEX S S e e t t h h c c o o W W a a r r r r a a n n t t y y O O p p e e r r a a t t i i n n g g I I n n s s t t r r u u c c t t i i o o n n s s ( ( c c o o n n t t . . ) )
-
Page 3: Warranty
Buyer has given SETHCO immediate written notice upon discovery of such defect. No allowance will be made for labor charges. SETHCO shall have the option of requiring the return of the defective material, transportation prepaid, to establish the claim. - Page 4 The equipment as received has been chosen for a certain application or service. DO NOT USE for any other application unless writ- ten permission is obtained from the SETHCO factory. Consult the SETHCO factory with all of the service requirements so that we can assist you in a successful reapplication.
- Page 5 OPERATING INSTRUCTIONS FOR SETHCO ZKX VERTICAL PUMPS GENERAL DESCRIPTION Sethco close coupled vertical pumps are centrifugal type pumping units designed for installation inside or outside of an open tank. All pump parts in contact with the fluid are PVDF. PRE-INSTALLATION All Sethco pumps are tested at the factory for proper operation.
- Page 6 SETHCO Thermoplastic Pumps A Met-Pro Fluid Handling Technologies Company OPERATING INSTRUCTIONS FOR SETHCO ZKX VERTICAL PUMPS ELECTRICAL CONNECTIONS All electrical work to the unit should be performed by a qualified technician. All local, state and federal electrical codes should be followed.
-
Page 7: Troubleshooting
SETHCO Thermoplastic Pumps A Met-Pro Fluid Handling Technologies Company OPERATING INSTRUCTIONS FOR SETHCO ZKX VERTICAL PUMPS TROUBLESHOOTING Refer to the following diagnostic section if hydraulic problems are encountered in the pump operation. NO DISCHARGE • Pump not primed • Speed too low •... - Page 8 SETHCO Thermoplastic Pumps A Met-Pro Fluid Handling Technologies Company ZKX 3/4CS OPERATIONAL START-UP CHECKLIST Pump mount is level and plumb. Mounting bolts are tight. Motor mounting bolts tight. Suction and discharge connections secure. Electrical connections secure and covered. Turn motor fan by hand, ensure that it does not bind.
- Page 11 ZKX 3/4CS CURVES (3500 RPM) 3500 RPM 3500 RPM...
- Page 13 NOTES...
- Page 14 . . s s e e t t h h c c o o . . c c o o m m • • i i n n f f o o @ @ s s e e t t h h c c o o . . c c o o m m SETH O ©COPYRIGHT 2009 MET-PRO CORPOR TION, SETHCO DIVISION ®...
Need help?
Do you have a question about the ZKX 3/4CS and is the answer not in the manual?
Questions and answers