Table of Contents
Advertisement
Quick Links
IDEAL CHEMICAL TEMPERATURE
80°F
(27°C)
TROUBLESHOOTING
For all technical
Scan with a QR reader app
on your smartphone to
advice and
be directed to technical
troubleshooting
downloads
call us toll-free at
1-800-565-9936
OPERATING INSTRUCTIONS
SUBSTRATE APPLICATION TEMPERATURE
40-100°F
(4-38°C)
SPECIAL REQUIREMENTS
• Use only in a well ventilated
area.
• To ensure trouble free
operations, change nozzle
after 30 seconds of non-use.
• Please read through the
TDS, MSDS, and Operating
Instructions prior to use.
ULTRASEAL PF-200 & PF-600
LOW PRESSURE SPRAY POLYURETHANE FOAM
TWO-COMPONENT DISPOSABLE
READ FIRST!
Important
Always read all operating, application and safety instructions before
using any products from Rivenco. Use in conformance with all municipal,
provincial and federal regulations and safety requirements. Failure to
strictly adhere to any recommended procedures and reasonable safety
precautions shall release Rivenco of all liability with respect to the
materials or the use thereof. For additional information and location of
your nearest distributor, call Rivenco 1.800.565.9936.
NOTE: Physical properties shown are typical and are to serve only as
a guide for engineering design. Results are obtained from specimens
under ideal conditions and may vary upon use, temperature and ambient
conditions. Right to change physical properties as a result of technical
progress is reserved. This information supersedes all previously published
data. Yields shown are optimum and will vary slightly depending on
ambient conditions and particular application. Read all product directions
and safety information before use. This product is organic, and therefore,
is combustible. Consult local building codes for specific requirements
regarding the use of cellular plastics or urethane foam in construction.
UltraSeal Spray Foam products are composed of a diisocyanate, hydrofluorocarbon
blowing agent and polyol. Consult the product's MSDS (available inside packaging and
at www.Rivenco.com) for specific information. The urethane foam produced from
these ingredients will support combustion and may present a fire hazard if exposed
to a fire or excessive heat about 240°F (116°C). Wear protective glasses or goggles,
nitrile gloves, and clothing that protects against dermal exposure. Use only in a
well ventilated area with certified respiratory protection or a powered air purifying
respirator (PAPR). See MSDS (available inside packaging and at
www.Rivenco.com) for specific information. For professional use only.
150 Curtis Drive • Guelph, ON N1K 1N5 Canada
1-519-822-0544 • 1-800-565-9936 • Fax 1-519-822-0543
SHAKING REQUIREMENTS
1
MINUTE
A
B
A
B
A
PERSONAL PROTECTIVE EQUIPMENT
Safety Glasses
Covers Skin
Respirator and/or Vapor
Avoid Breathing Vapors Provide
Respirator OV/Pre-filter
Good Ventilation
info@rivenco.com • www.Rivenco.com
A
B
B
Nitrile Gloves
Advertisement
Table of Contents
Summary of Contents for Rivenco Ultraseal PF-200
- Page 1 TWO-COMPONENT DISPOSABLE Important Always read all operating, application and safety instructions before using any products from Rivenco. Use in conformance with all municipal, provincial and federal regulations and safety requirements. Failure to strictly adhere to any recommended procedures and reasonable safety precautions shall release Rivenco of all liability with respect to the materials or the use thereof.
- Page 2 ** Based on the EPA’s 2011 working draft-Ventilation Guidelines for SPF (Spray Polyurethane Foam), refer to www.epa.gov/dfe for additional information please visit the following websites: www.spraypolyurethane.org or www.sprayfoam.org SET-UP PROCEDURE FOR ULTRASEAL PF-200 TWO-COMPONENT MODEL Initial Prep 1. Wear protective glasses with sideshields or goggles, nitrile gloves, 2.
- Page 3 Wear protective glasses with sideshields or goggles, nitrile gloves, and clothing that protects against dermal exposure. Use only in a well ventilated area with certified respiratory protection or a powered air nozzle, use petroleum purifying respirator (PAPR). See MSDS (available inside packaging and at www.Rivenco.com). jelly on face of gun. After attaching nozzle, For best results, use when material is between 75–85°F (24–29°C), see TDS for formula specific...
- Page 4 UltraSeal Spray Foam products are composed of a diisocyanate, hydrofluorocarbon blowing agent and polyol. Consult the product’s MSDS (available inside packaging and at www.Rivenco.com) for specific information. The urethane foam produced from these ingredients will support combustion and may present a fire hazard if exposed to a fire or excessive heat about 240°F (116°C).
Need help?
Do you have a question about the Ultraseal PF-200 and is the answer not in the manual?
Questions and answers