Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for IEI Technology AFL2-EM-RFID-KIT
- Page 1 AFL2-EM-RFID-KIT01 IRFD-210 RFID Reader MODEL: AFL2-EM-RFID-KIT EM RFID re a d e r, 125K Hz, w/o LED in d ic a to r, fo r AFL2-W07A/08A/10A/W10A/12A/15A/W15B/17A/W19A S e rie s , IEI As s e m b ly On ly, R10...
- Page 2 AFL2-EM-RFID-KIT01 Re vis io n Date Version Changes 17 April, 2014 1.00 Initial release P a g e ii...
- Page 3 AFL2-EM-RFID-KIT01 Co p yrig h t COP YRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
-
Page 4: Table Of Contents
AFL2-EM-RFID-KIT01 Ta b le o f Co n te n ts 1 INTRODUCTION ......................1 1.1 AFL2-EM-RFID-KIT01 O ................2 VERVIEW 1.1.1 AFL2-EM-RFID-KIT01 Features ..............2 1.2 T ..................3 ECHNICAL PECIFICATIONS 2 CONNECTORS ......................4 2.1 AFL2-EM-RFID-KIT01 RFID R .............. - Page 5 AFL2-EM-RFID-KIT01 4.6.5 Selective Read ....................18 4.6.6 Set Control Word ....................19 4.6.7 Read Control Word ................... 19 4.6.8 New Password ....................20 4.6.9 Reset Tag ......................20 4.7 EM4305 ........................21 4.7.1 Setup ......................... 21 4.7.2 Configuration ....................21 4.7.3 Read Block .......................
- Page 6 AFL2-EM-RFID-KIT01 Lis t o f Fig u re s Figure 1-1: AFL2-EM-RFID-KIT01 ....................2 Figure 2-1: Connector and Jumper Locations ................5 Figure 2-2: LED Locations (Solder Side) ..................5 Figure 2-3: Buzzer Connector Location ..................6 Figure 2-4: RS-232 and USB Connector Locations ..............7 Figure 4-1: Software Interface .....................14 Figure 4-2: Open IRFD-210 ......................14 Figure 4-3: EM4100 ........................15...
- Page 7 AFL2-EM-RFID-KIT01 Lis t o f Ta b le s Table 1-1: Technical Specifications ....................3 Table 2-1: Peripheral Interface Connectors and Indicators ............6 Table 2-2: Buzzer Connector Pinouts ................... 7 Table 2-3: RS-232 and USB Connector Pinouts ................7 Table 3-1: Package List Contents ....................11 P a g e vii...
-
Page 8: Introduction
AFL2-EM-RFID-KIT01 Ch a p te r In tro d u c tio n P a g e 1... -
Page 9: Afl2-Em-Rfid-Kit01 Overview
AFL2-EM-RFID-KIT01 1.1 AFL2-EM-RFID-KIT01 Ove rview Figure 1-1: AFL2-EM-RFID-KIT01 The AFL2-EM-RFID-KIT01 is an RFID reader for Low Frequency (LF) RFID systems and compliant with 11784 11785 industrial standards. AFL2-EM-RFID-KIT01 also comes with a utility and a software development kit (SDK) for configuring reader module and writing/reading tags. -
Page 10: Technical Specifications
AFL2-EM-RFID-KIT01 1.2 Te c h n ic a l Sp e c ific a tio n s The specifications for the Intel based embedded systems are listed below. AFL2-EM-RFID-KIT01 S u p p o rt P ro to c o l ISO 11784, ISO 11785 (EM4305/EM4450 R/W) 125 KHz RF Fre q u e n c y... -
Page 11: Connectors
AFL2-EM-RFID-KIT01 Chapter Co n n e c to rs P a g e 4... -
Page 12: Afl2-Em-Rfid-Kit01 Rfid Reader
AFL2-EM-RFID-KIT01 2.1 AFL2-EM-RFID-KIT01 RFID Re a d e r The following sections describe the relevant components and jumpers on the RFID reader module. 2.1.1 AFL2-EM-RFID-KIT01 La yo u t Figure 2-1 shows the on-board peripheral connectors and rear panel LEDs. Figure 2-1: Connector and Jumper Locations Figure 2-2: LED Locations (Solder Side) 2.1.2 P e rip h e ra l In te rfa c e Co n n e c to rs... -
Page 13: Internal Peripheral Connectors
AFL2-EM-RFID-KIT01 Co n n e c to r Typ e La b e l Function active LED (solder side) Power LED (solder side) Table 2-1: Peripheral Interface Connectors and Indicators 2.2 In te rn a l P e rip h e ra l Co n n e c to rs This section has complete descriptions of all the internal peripheral connectors on the AFL2-EM-RFID-KIT01. -
Page 14: Rs-232 And Usb Connector
AFL2-EM-RFID-KIT01 Pin No. Description MIC+ Table 2-2: Buzzer Connector Pinouts 2.2.3 RS -232 a n d US B Co n n e c to r CN La b e l: 6-pin header CN Typ e : CN Lo c a tio n : See Figure 2-4 CN P in o u ts : See Table 2-3... -
Page 15: Led Indicators
AFL2-EM-RFID-KIT01 2.2.4 LED In d ic a to rs CN La b e l: D1 a n d D2 (S o ld e r S id e ) On-board LED CN Typ e : There are two LED indicators located on the solder side of the AFL2-EM-RFID-KIT01 module to indicate the power status and activation status. -
Page 16: Unpacking
AFL2-EM-RFID-KIT01 Chapter Un p a c kin g P a g e 9... -
Page 17: Anti - Static Precautions
AFL2-EM-RFID-KIT01 3.1 An ti-s ta tic P re c a u tio n s WARNING! Static electricity can destroy certain electronics. Make sure to follow the ESD precautions to prevent damage to the product, and injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the AFL2-EM-RFID-KIT01-R10. -
Page 18: Table 3-1: Package List Contents
AFL2-EM-RFID-KIT01 Qu a n tity Ite m Im a g e AFL2-EM-RFID-KIT01-R10 Utility CD Table 3-1: Package List Contents P a g e 11... -
Page 19: Software Application
AFL2-EM-RFID-KIT01 Chapter S o ftwa re Ap p lic a tio n P a g e 12... -
Page 20: Chapter Overview
AFL2-EM-RFID-KIT01 4.1 Ch a p te r Ove rview This chapter describes the use of the IRFR-210 module control program. The IRFD-210 Tools is a program providing end user interface to help the user to communicate with 125 kHz operating frequency transponders using IRFD-210. The IRFD-210 Tools provides almost complete command set to control the IRFD-210 reader and communicate with the following EM transponders: ... -
Page 21: Open Irfd-210
AFL2-EM-RFID-KIT01 Figure 4-1: Software Interface 4.4.1 Op e n IRFD-210 To start using the IEI IRFD-210 Tools with the IRFD-210 reader, follow the steps below. S te p 1: Click Open Device from the File drop-down menu. S te p 2: The following window appears. -
Page 22: Em4100
AFL2-EM-RFID-KIT01 4.5 EM4100 The IRFD-210 is capable of reading EM4100 tag UID. To read EM4100 tag, follow the steps below. S te p 1: Click EM4100 from the list of the Tag Selection tool. S te p 2: Place a single EM4100 tag on the IRFD-210. Click the IRFR_4100ID button. -
Page 23: Em4450
AFL2-EM-RFID-KIT01 4.6 EM4450 Figure 4-4: EM4450 4.6.1 S e tu p S te p 1: Click EM4450 from the list of the Tag Selection tool. S te p 2: Place a single EM4450 tag on the IRFD-210. S te p 0: 4.6.2 Re a d Blo c k To read a single block, the user should: Select one block from the Memory Map list. -
Page 24: Figure 4-5: Write Block Value
AFL2-EM-RFID-KIT01 Click the Write Block button. S te p 2: Enter a value for the new block. S te p 3: Click the OK button. S te p 4: S te p 0: Figure 4-5: Write Block Value NOTE: The Write Block command can only be used for reading or writing (RW) blocks. -
Page 25: Login
AFL2-EM-RFID-KIT01 4.6.4 Lo g in The Login command is used to access protected memory areas. The login status is visible in the Login Status window under the Login command button. To login, the user should: Click the Login button. S te p 1: Enter a current password value. -
Page 26: Set Control Word
AFL2-EM-RFID-KIT01 4.6.6 S e t Co n tro l Wo rd The Set Control Word command is used to set the Control Word located in the Block 2. When clicking the Set Control Word button, the actual content of the Control Word is read first. -
Page 27: New Password
AFL2-EM-RFID-KIT01 4.6.8 Ne w P a s s wo rd The New Password command is used to change the password. To change the password, the user should: S te p 1: Click the New Password button. S te p 2: Enter the current password. -
Page 28: Em4305
AFL2-EM-RFID-KIT01 4.7 EM4305 Figure 4-9: EM4305 4.7.1 S e tu p S te p 1: Click EM4305 from the list of the Tag Selection tool. S te p 2: Place a single EM4305 tag on the IRFD-210. S te p 0: 4.7.2 Co n fig u ra tio n Before using any command it is necessary to ensure that the reader and EM4305 transponder have the same configuration. -
Page 29: Figure 4-10: Em4305 Configuration
AFL2-EM-RFID-KIT01 S te p 2: Choose Configuration mode, Code/Data Rate and Last Word Read (LWR). For example; both EM4305 and Reader configuration, Bi/32, and LWR=8. S te p 3: Click the Set button. S te p 4: If the configuration command proceeds successfully the Configuration window closes automatically. -
Page 30: Read Block
AFL2-EM-RFID-KIT01 4.7.3 Re a d Blo c k Click one block from the Memory Map list. S te p 1: S te p 2: Click the Read Block button. S te p 3: Click the OK button. S te p 0: 4.7.4 Write Blo c k S te p 1: Click one block from the Memory Map list. -
Page 31: New Password
AFL2-EM-RFID-KIT01 Figure 4-11: Login – Enter Password 4.7.6 Ne w P a s s wo rd NOTE: Before changing the password values the transponder has to be in Logged state (see Login described above). The New Password command is used to change the password. To change the password, the user should: S te p 1: Click the New Password button. -
Page 32: Figure 4-12: Set Protection Bits
AFL2-EM-RFID-KIT01 WARNING: The bits in Protection word that are stored in the Protection words (Block 14 and 15) are one time programmable (OTP) which means that once they have been set they can not be reset any more. S te p 1: Click the Protection button. -
Page 33: Disable
AFL2-EM-RFID-KIT01 4.7.8 Dis a b le The Disable command is accepted in the case the Disable bit in Tag Special Bits is set to 1 (see Configuration -> EM4305 Special bits selection). When this command is detected, EM4305 or EM4205 tag stops all operations until power-up. If the Disable command is not accepted (Disable bit is set to 0), EM4305 or EM4205 tag returns in Default Read mode. -
Page 34: Initialize Tag Value
AFL2-EM-RFID-KIT01 4.7.10 In itia lize Ta g Va lu e The initialize tag value, enter the desired tag data. Then, click the Write button within the Initialize section. Figure 4-14:InitializeTag Value P a g e 27... -
Page 35: A Irfd-210 Tool Library
AFL2-EM-RFID-KIT01 Ap p e n d ix IRFD-210 To o l Lib ra ry P a g e 28... -
Page 36: Irfd-210-Api
AFL2-EM-RFID-KIT01 A.1 IRFD-210-AP I IRFR_200_API int IRFR_200_OPEN(int i_DeviceType,int i_ComPort); IRFR_200_API int IRFR_200_4100ID(unsigned char *ID); IRFR_200_API int IRFR_200_4450_READ(char addr1,char addr2 ,unsigned char*Data); IRFR_200_API int IRFR_200_4450_WRITE(char addr,unsigned char *data); IRFR_200_API int IRFR_200_4450_LOGIN(unsigned char *data); IRFR_200_API int IRFR_200_4450_READCONTROL(unsigned char *data); IRFR_200_API int IRFR_200_4450_READWORD(unsigned char *data);... -
Page 37: B Hazardous Materials Disclosure
AFL2-EM-RFID-KIT01 Ap p e n d ix Ha za rd o u s Ma te ria ls Dis c lo s u re P a g e 30... -
Page 38: Hazardous Materials Disclosure Table For Ipb Products Certified As R Ohs Compliant Under 2002/95/Ec Without Mercury
AFL2-EM-RFID-KIT01 B.1 Ha za rd o u s Ma te ria ls Dis c lo s u re Ta ble for IP B P ro d u c ts Ce rtifie d a s Ro HS Co m p lia n t Un d e r 2002/95/EC With o u t Me rc u ry The details provided in this appendix are to ensure that the product is compliant with the Peoples Republic of China (China) RoHS standards. - Page 39 AFL2-EM-RFID-KIT01 P a rt Na m e To xic o r Ha za rd o u s S u b s ta n c e s a n d Ele m e n ts Le a d Me rc u ry Ca d m iu m He xa va le n t P o lyb ro m in a te d...
- Page 40 AFL2-EM-RFID-KIT01 此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符 合中国 RoHS 标准规定的限量要求。 本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的 年限。本产品可能包含有较短的环境友好使用期限的可替换元件，像是电池或灯管，这些 元件将会单独标示出来。 部件名称 有毒有害物质或元素 铅 汞 镉 六价铬 多溴联苯 多溴二苯 醚 (P b ) (Hg ) (Cd ) (CR(VI)) (P BB) (P BDE) 壳体 显示 印刷电路板 金属螺帽 电缆组装 风扇组装 电力供应组装 电池 O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ/T11363-2006 标准规定的限量要求以下。 X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出...
- Page 41 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: AFL2-EM-RFID-KIT01-R10...