Tecnologic TLV 10 Operating Instructions

TLV 10
MICROPROCESSOR-BASED
DIGITAL ELECTRONIC
THERMOMETER

OPERATING INSTRUCTIONS

Vr. 01 (ENG) - 11/05 - cod.: ISTR 06939
TECNOLOGIC S.p.A.
VIA INDIPENDENZA 56
27029 VIGEVANO (PV) ITALY
TEL.: +39 0381 69871
FAX: +39 0381 698730
internet : http:\\www.tecnologic.it
e-mail: info@tecnologic.it
FOREWORD
This manual
necessary for the product to be installed
correctly
maintenance and use; we therefore recommend
that the utmost attention is paid to the following
instructions and to save it.
This document is the exclusive property of TECNOLOGIC
S.p.A. which forbids any reproduction and divulgation , even
in part, of the document, unless expressly authorized.
TECNOLOGIC S.p.A. reserves the right to make any formal or
functional changes at any moment and without any notice.
Whenever a failure or a malfunction of the device may cause
dangerous situations for persons, thing or animals, please
remember that the plant has to be equipped with additional
devices which will guarantee safety.
Tecnologic S.p.A. and its legal representatives do not assume
any responsibility for any damage to people, things or animals
deriving from violation, wrong or improper use or in any case
not in compliance with the instrument's features.
TECNOLOGIC - TLV 10 - OPERATING INSTRUCTIONS - Vr.01 - 11/05 - ISTR 06939 - PAG. 1
contains the
and also instructions
INDICE
1 INSTRUMENT DESCRIPTION
1.1 GENERAL DESCRIPTION
1.2 FRONT PANEL DESCRIPTION
2 PROGRAMMING
2.1 PARAMETERS PROGRAMMING
2.2 PARAMETER PROTECTION USING THE PASSWORD
2.3 PARAMETERS PROGRAMMING LEVEL
3 INFORMATION ON INSTALLATION AND USE
3.1 PERMITTED USE
3.2 MECHANICAL MOUNTING
3.3 ELECTRICAL CONNECTIONS
3.4 ELECTRICAL WIRING DIAGRAM
4 FUNCTIONS
4.1 MEASURING AND VISUALIZATION
4.2 PARAMETERS CONFIGURATION BY KEY01
5 PROGRAMMABLE PARAMETERS TABLE
6 PROBLEMS , MAINTENANCE AND GUARANTEE
6.1 SIGNALLING
6.2 CLEANING
6.3 GUARANTEE AND REPAIRS
7 TECHNICAL DATA
7.1 ELECTRICAL DATA
7.2 MECHANICAL DATA
7.3 MECHANICAL DIMENSIONS, PANEL CUT-OUT AND
MOUNTING
7.4 FUNCTIONAL DATA
7.5 INSTRUMENT ORDERING CODE
1 - INSTRUMENT DESCRIPTION
1.1 - GENERAL DESCRIPTION
TLV 10 is a digital microprocessor based thermometer. The
instrument has one input for PTC or NTC temperature probes that
can be configured. The instrument is equipped with 4 programme
keys and a 4-digit display. Other important characteristics of the
instrument
personalised password, configuration of parameters via the KEY 01
device and the possibility of power supply in the range 100 ... 240
VAC.
1.2 - FRONT PANEL DESCRIPTION
information
1 - Key P : Used for programming the function parameters
2 - Key DOWN : Used for decreasing the values to be set and for
for its
selecting the parameters.
3 - Key UP : Used for increasing the value to be set and for
selecting the parameters.
4 - Key U : In the "hidden" parameter programming mode it's used
to modify the visibility of the parameters (see par. 2.3).
5 - Led SET : Indicates the input in programming mode and the
programming level of the parameters.
2 - PROGRAMMING
2.1 - PARAMETERS PROGRAMMING
To access the instrument's function parameters, press the key P
and keep it pressed for about 5 seconds, after which the SET led
will light up, the display will visualised the code that identifies the
first parameter.
Using the UP and DOWN keys, the desired parameter can be
selected and pressing the P key, the display will alternately show
the parameter code and its setting that can be changed with the UP
and DOWN keys.
are: programme parameters
TLV 10
protection using
4
3
2
1
5