iHold Music 4LP-S Quick Start Manual

•
To use device as an Adapter with external audio source do not insert USB
•
To use internal audio, Insert the USB flash drive
use a different power adapter or the unit will be damaged – it may take up to 60 seconds before playback starts with USB flash drive blinking
•
Confirm that white LED lights in front of unit are double blinking –
•
Use one of your telephones and unplug the cord for L1/L2 from it and connect it to L1/L2 IN jack on iHold device , now
connect the L1/L2 OUT jack to your telephone using the provided cord, check for dial tone on lines 1 & 2
•
If applicable unplug the cord for L3/L4 from telephone and connect it to L3/L4 IN jack on iHold device, now connect the
L3/L4 OUT jack to your telephone using the provided cord, check for dial tone on lines 3 & 4
•
Wait till LED lights turn OFF - observe that after you connect the lines the blinking lights 1
seconds
(on non existing lines the lights keep blinking and that is OK)
•
Turn the speaker ON to confirm audio is playing and adjust the volume to mid level
(If using External audio connect it to RCA jack as shown and use your external audio volume control)
Please note: just
one telephone
may be connected
to this device,
other telephones
remain connected
to their own wall
jacks and they all
work.
Switch set to 1: Hold button activation
Use this setting when all phones are corded ( not cordless type like corded base station + portables) and all are same model
and are compatible for hold button activation (for example all are ATT 993, At&t ML 17929)
Operation: make or receive a real call, the LED on the iHold turns ON solid, then simply press the
telephone, the Music will be heard to the caller and the LED on the iHold device starts to BLINK , to return to the call just re-
select that line. (Be sure to allow 1 or 2 seconds before putting a call on HOLD).
The 1 time your are setting the device If it did not work hang up and try it again 2 or 3 times.
st
If music on hold does not work in this setting
Switch set to 2: Flash activation
This setting utilizes Flash then Hold
activation by pressing Flash then Hold
Operation: make or receive a real call, the LED on the iHold turns ON solid, then simply press the
HOLD
button on your telephone, the Music will be heard to the caller and the LED on the iHold device starts to BLINK , to
return to the call just re-select that line and speak into the audio to stop it for example say : "Hi I am Back"
Alternatively you may just press
to voice deactivate or Flash to stop the audio)
If for some reason you are not able to voice -deactivate, try speaking louder or more direct into the microphone or use the Flash
button to deactivate audio.
The FLASH button could be labeled as Call Wait or LINK or ON or TALK button on some telephones
In setting 2 do not make the volume too loud or the audio could sound flickering when heard on Hold
Hold 4LP-S
i
Advanced Music On Hold Adapter / All-In-One device
(or SD card)
110 - 240 V
Not used
A B C 1 2 3
Speaker
ON OFF OFF
L1 L2
Volume
C
(for example ATT 1040,1070,1080)
1 2 3
C
activation method, this setting supports any phone or any mix of brands with instant
FLASH
to stop the audio (Be sure the call has been on Hold at least 5 seconds before you try
(or SD card)
1 then connect the included AC adapter
st
for regular phones continue,
Audio output
to PBX or
external
audio Input
L3/L4 L3/L4
OUT IN
SD card slot
USB drive
Not used
1 2 3
, hang up and change switch to setting 2 or 3
then connect the included AC adapter
(110- 240 V AC to 5V DC) do not
for PBX phones go to page P4
stops then turns OFF after 20
st
(you can Turn it OFF any time)
Back
L1/L2 L1/L2
OUT IN
NXT L3 L4
Front
LED
button on your
HOLD
FLASH then
P1