Parts And Materials; Siting Requirements; Unpacking - Star Trac Instinct Inner/Outer Thigh Machine Owner's Manual

A S
SSEMBLY AND ETUP

PARTS AND MATERIALS

The following parts are included with the STAR TRAC INSTINCT INNER THIGH / OUTER THIGH:
1 Frame, Weight Stack
2 Frame, Main
3 Frame, Center
4 Crossbeam, Right
5 Crossbeam, Left
6 Pedal, Right
7 Pedal, Left
8 Bracket, Thigh Cushion
9 Bracket, Pedal
10 Flywheel, Range-of-Motion
11 Lever, Flywheel
12 Cover, Frame
13 Cover, Flywheel
15 Pulley/Clamp
16 Link, Pedal
17 Plate, Top, Weight Stack
18 Weight, 5lb
19 Weight, 10lb
23 Selector Pin
25 Clip, Shaft
31 Washer
32 Retainer, Belt
37 Cushion, Seat
38 Cushion, Back
39 Cushion, Thigh
40 Cushion, Thigh
45 Mat
47 Shaft, Pedal
T R
OOLS EQUIRED
Most STAR TRAC INSTINCT machines can be assembled using the following tools:
Metric Hex Key Wrenches - 2.5mm, 5mm, 6mm, 8mm, 10mm
Metric Open-End Wrenches - 10mm, 15mm, 17mm
Metric Ratchet Socket Wrench Set (including 17mm socket)
Torque Wrench
Your INSTINCT INNER THIGH / OUTER THIGH includes a hex key set and combination open-end wrench.

SITING REQUIREMENTS

Your INSTINCT INNER THIGH / OUTER THIGH requires approximately 32 square feet of floor space to ensure safe opera-
tion of the unit.

UNPACKING

Your INSTINCT INNER THIGH / OUTER THIGH is shipped in one or more shipping cartons. Each carton will generally con-
tain one subassembly of the entire unit. To unpack:
Remove the shipping straps from the outside of each shipping carton.
Open the top of each carton and fold back all four flaps.
6 STAR TRAC INSTINCT INNER THIGH / OUTER THIGH O
1 48 Guide Post, Weight Stack
1 50 Spacer, Shaft
1 51 Washer, 32M
1 52 Cover, Front
1 53 Belt
1 54 Belt
1 55 Shroud, Lower, Front
2 56 Shroud, Lower, Rear
1 57 Shroud, Upper
1 61 Support, Weight Stack
1 62 Cap, Rubber
1 63 Cap, Rubber
1 66 Nut, Tapped Hole
1 67 Screw, Button Head Socket Cap, 10X130M
1 68 Screw, Button Head Socket Cap, 10X80M
1 69 Screw, Button Head Socket Cap, 10X75M
3 72 Screw, Button Head Socket Cap, 10X30M
6 73 Screw, Button Head Socket Cap, 10X35M
1 74 Screw, Button Head Socket Cap, 10X45M
2 75 Screw, Button Head Socket Cap, 10X25M
2 76 Screw, Retaining
4 79 Screw, Button Head Socket Cap, 8X20M
1 82 Lock Nut, Nylon Insert, 10M
1 85 Washer, 11M
2 86 Washer, 9M
2 87 Washer, Spring, 8M
1 88 Washer, Spring, 10M
2
Channel Lock Pliers
Vice Grip Pliers
Rubber Mallet
Phillips Head Screwdriver - #2
W B
EIGHT ELT
WARNING: REPLACE WORN WEIGHT BELTS IMMEDIATELY. FAILURE TO COMPLY CAN RESULT IN HAZ-
ARDOUS CONDITIONS FOR USERS OR OTHER BYSTANDERS.
Inspect all weight belts for evidence of excessive wear or other damage. Give particular attention to the following conditions:
2
1
1
1
1
1
1
1
2
2
2
2
6
6
2
8
2
10
2
4
4
18
16
46
18
6
4
' M STAR TRAC INSTINCT INNER THIGH / OUTER THIGH O
WNER S ANUAL
I R
NSPECTION EQUIREMENTS
Torn or cracked belt
Exposed belt cords
Worn edges
' M
WNER S ANUAL
15