Mi400-24V/Rts - Acksys MI400 Series Technical Documentation Manual

MI400-24V/RTS

CONNECTOR AND SWITCHES
FRONT
POWER MI400
ACKSYS
TX
RX
/24V
RTS/DTR
CTS
DSR/DCD
232 422-485
DTE
DCE
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 910
on on
5 KV OPTO-ISOLATED RS232/422-485 CONVERTER
L.E.D. ON FRONT
signal " ON " signal " OFF "
232 232
DTE
DCE
1 2 3 4 5 6 7 8
on
SW1 SW2
SW1 = DTE/DCE 1 = TRANSMISSION VALIDATION
INTERFACE SELECTION 2 = TRANSMISSION VALIDATION
3 = TRANSMISSION VALIDATION
DTE = ex P.C. 4 = CTS CONTROL
ex TERMINAL 5 = CTS CONTROL
6 = CTS DELAY
DCE = ex MODEM 7 = DSR/DCD CONTROL
ex MINI 8 = DSR/DCD CONTROL
SEE CONFIGURATION TABLE PAGE 3-5 AND PAGE 3-6
FEMALE LINE CONNECTOR
5
4 SCREW CONNECTEUR +
CABLE COVER WITH PHEONIX
3
CONTACT 5 POINT FEMALE
2 STRAPS MSTB2.5/5STF5.08
1
18 GAUGE MAXIMUM 2.5 mm2
5 KVdc between RS232 and RS422A/485
ISOLATIONS: 2,5 KVdc between RS232 and +- 24Vdc
2,5 KVdc between RS422/485 and +- 24Vdc
422-485
1 2 3 4 5 6 7 8 910
on
SW3
1 = RS422A MODE
2 = RS422A TERMINATION RESISTOR
3 = RS422A -BIAS
4 = RS422A +BIAS
5 = RS485 MODE
6 = RS485 TERMINATION RESISTOR
7 = RS485 -BIAS
8 = RS485 +BIAS
9 = RS485 ECHO
10 = UNSUSED
(P3)
FEMALE POWER CONNECTOR
PHOENIX CONTACT 3 POINT
FEMALE MSTB2.5/3ST5.08
18 GAUGE MAXIMUM 2.5 mm2
REAR
CAT
dc
1 2 3 4 5 6 7 8 910
on
POWER
LOCK
RS422-485
RS232
ACKSYS 39 11 62 81
A T
UTOMATIC RANSMISSION
1 2 3 4 5 6 7 8 910
on
SW4
1 = SPEED SELECTION
2 = SPPED SELECTION
3 = SPEED SELECTION
4 = SPEED SELECTION
5 = SPEED SELECTION
6 = FORMAT SELECTION
7 = FORMAT SELECTION
8 = FORMAT SELECTION
9 = FORMAT SELECTION
10 = FORMAT SELECTION
(P4)
RS422-485
1 2 3 4 5
P3
RS422A mode
1 = +RX
2 = -RX
3 = +TX
4 = -TX
5 = GND
CAT SW4 SW5
1 2 3 4 5 6 7 8 910
on
P2
SUB D 9 MALE
PHOENIX CONTACT 5 POINT MALE
MSTB2.5/5GF5.08
PHOENIX CONTACT 3 POINT MALE
MSTB2.5/3G5.08
C (CAT)
ONTROL
SW5
SW5 = SELECTION OF TRANSMISSION
VALIDATION BY RTS/DTR
OR AUTOMATICALLY
dc
POWER
P4
RS485 mode 20 Vdc to 30 Vdc
150 mA Max
1 = NC
2 = NC
3 = +TX/+RX
4 = -TX/-RX
5 = GND
PAGE 3-4
P3
P4