Related Manuals for B+B KNX-GSM Gateway
Summary of Contents for B+B KNX-GSM Gateway
- Page 1 Documentation KNX-GSM Gateway EIB/KNX remote control and alarming with a mobile phone Order number: E001-H031007...
- Page 2 IMPORTANT-READ CAREFULLY: This b+b End-User License Agreement ("EULA") is a legal agreement between you (either an individual or a single entity) and b+b Automa- tions- und Steuerungstechnik GmbH, for the software product identified above, which includes computer software and may include associ- ated media, printed materials, and "online"...
- Page 3 Copyright 1998 - 2009 b+b Automations- und Steuerungstechnik GmbH. All rights reserved. Microsoft and Windows are trademarks of Microsoft Corporation.
-
Page 4: Table Of Contents
SIM cards..............................7 GSM antenna ..............................7 Overview..............................8 Installation instruction ..........................9 Functions .............................10 LED description ............................10 Parameterisation phase...........................10 System startup phase ..........................11 Test mode..............................12 Alarm input ..............................12 Configuration with the EIBDoktor software..................13 Transfering the configuration.......................19 © b+b Automations- und Steuerungstechnik GmbH KNX-GSM GATEWAY.DOC... -
Page 5: Highlights Knx-Gsm Gateway
Monitor your EIB/KNX – installation via mobile phone over GSM network Contents of delivery • KNX-GSM Gateway • Dualband GSM antenna (supports GSM frequency bands 900MHz and 1800MHz) • EIBDoktor software for configuration • Documentation © b+b Automations- und Steuerungstechnik GmbH KNX-GSM GATEWAY.DOC... -
Page 6: Introduction
(e.g. “Temperature > x°C”) occur. This can be used to inform the user about interferences. The KNX-GSM Gateway supports the widespread mobile phone standard GSM. This is why it can be used in almost any place. -
Page 7: Sim Cards
SIM cards A SIM card from a GSM network provider is needed for communication in the GSM network. This SIM card identifies the user in the GSM network. The KNX-GSM Gateway supports 1,8V and 3V mini SIM cards. Important: Bevor changing the SIM card you have to cut the power supply from the KNX-GSM Gateway. -
Page 8: Overview
Rev: 03/2009 Page 8 of 19 KNX-GSM Gateway verview Figure 1: KNX-GSM Gateway overview GSM antenna, SMA connector (female) Ant. Programming LED Programming Button EIB/KNX connector SIM card holder Power supply 230V AC : Protective conductor N: Neutral conductor L1: Phase conductor Alarm input, n.c. -
Page 9: Installation Instruction
KNX-GSM Gateway Installation instruction Mount the KNX-GSM Gateway on DIN rail. After this insert the SIM card in the SIM card holder (A5). While inserting the SIM you should see the SIM card’s backside (side without contacts). The next step is to connect the Gateway to the EIB/KNX bus system and to the power supply 230V AC. If everything is connected properly you can switch on power supply. -
Page 10: Functions
After installing and configuring the KNX-GSM Gateway it is ready for usage. The KNX-GSM Gateway has seven light emitting diodes (LEDs) on its top to visualize occurred er- rors to the user. The meaning of these LEDs is described in the following section. -
Page 11: System Startup Phase
Important: You have to switch of the power supply before inserting the SIM card in the SIM card- holder! This is important to save the SIM card from damage!. Next, if a SIM card is inserted in the KNX-GSM Gateway, the configured PIN is checked. If the PIN is rejected by the SIM card, the LED starts blinking (ca. -
Page 12: Test Mode
Test mode It is also possible to check if the KNX-GSM Gateway is in operation and is logged in the GSM net- work even if you are on the way. You just have to call the KNX-GSM Gateway’s mobile phone num- ber from any telephone. -
Page 13: Configuration With The Eibdoktor Software
KNX-GSM Gateway Configuration with the EIBDoktor software The KNX-GSM Gateway needs a correct configuration to work properly. This configuration can be generated with the EIBDoktor software, the configuration data transfer can be done directly with the EIBDoktor or with the ETS software. - Page 14 Sending a SMS by incoming EIB data Up to 100 different events and messages can be stored in the Gateway. Push the button „Add…“ to define a new message, the following window will appear: © b+b Automations- und Steuerungstechnik GmbH KNX-GSM GATEWAY.DOC...
- Page 15 Here you can define up to 100 different texts, by selecting a number in the list, entering the text, and pressing the „Store text“ button. To use this text in a message, select the text in the list and press “OK”: © b+b Automations- und Steuerungstechnik GmbH KNX-GSM GATEWAY.DOC...
- Page 16 Up to eight time ranges are possible;: After you have defined your message, pressing “OK” will add it to the list in the main window: © b+b Automations- und Steuerungstechnik GmbH KNX-GSM GATEWAY.DOC...
- Page 17 Message on start of gateway From (time) every (n) hours Each of this message can be connected to one of the 100 message texts (button „…“), and to up to eight receivers (E1 – E8). © b+b Automations- und Steuerungstechnik GmbH KNX-GSM GATEWAY.DOC...
- Page 18 100 group addresses in the combo box. “OK” will add a GA, “Delete“ will remove the se- lected GA from the list. If you don’t want to allow any writing, simply activate this option and leave the GA list empty. © b+b Automations- und Steuerungstechnik GmbH KNX-GSM GATEWAY.DOC...
-
Page 19: Transfering The Configuration
“Start” in the EIBDoktor software. If you now go to the KNX-GSM Gateway configuration window, the button „Transfer to GW“ is avail- able. By pressing this button the data transfer will start. Please note: if the serial number of the gate- way is wrong, or the gateway is not connected to the EIB, an error message box will appear after a short time.
Need help?
Do you have a question about the KNX-GSM Gateway and is the answer not in the manual?
Questions and answers