Advertisement
Quick Links
FGP
Bench
Installation Guide
Backless, 70in
Backless, 120in
Included components (surface mount)
4x – 5/8‐11 thread
4x – M6‐1 x 25mm
Surface mt bolt
Set screw
Tools Required
Hammer drill with masonry bits
•
For surface mount option:
•
(4) zinc‐plated drop‐in anchors for 5/8‐11 thread size, for use with Magni‐coated bolts
•
3mm hex key
Slotted screw driver
•
For embedded option:
•
For embedded mount option: chemical anchoring adhesive (Hilti HIT RE 500 or
equivalent)
HANDLE WITH CARE! The finish can be scuffed by contact with tools, concrete,
or other abrasive surfaces. Protect the finish from damage during installation.
Backed, 120in
Backed, 70in
Included components (embedded)
4x – M8 x 1.25 x 100mm
Embedded threaded rod
INSTALLATION PROCEDURE:
Bench ships fully assembled. Freestanding unit can be set in place.
FOR EMBEDDED MOUNT:
1.
Turn bench upside down on protective surface.
2.
Remove four outer screws from glides as shown in Fig. 1. Leave glides installed.
3.
Install four threaded rods as shown in Fig. 2.
4.
Set unit in position and mark hole locations.
5.
Move unit aside.
6.
Drill holes according to Fig. 3. Clear holes of debris.
7.
Set unit back in position, ensuring that threaded rods are not resting on the bottom
of the hole. If necessary, move unit and drill holes deeper.
8.
Fill holes with adhesive to level recommended by adhesive manufacturer.
9.
Set unit in position. Wipe away excess adhesive before it cures.
FOR SURFACE MOUNT:
1.
Turn bench upside down on protective surface.
2.
Install surface mount bolts and set screws as shown in Fig. 4.
3.
Set unit in position and mark hole locations.
4.
Move unit aside. Remove surface mount bolts and set screws.
5.
Drill holes according to concrete anchor manufacturer's recommendations.
6.
Clear holes of debris.
7.
Install concrete anchors (not included).
8.
Install surface mount bolts into concrete anchors.
9.
Set bench in position over surface mount bolts.
10. Install set screws as shown in Fig. 5.
Date: September 27, 2016
www.landscapeforms.com
Ph: 800.521.2546
Page 1 of 2
Advertisement
Summary of Contents for Lanscape Forms FGP Series
- Page 1 Date: September 27, 2016 Bench www.landscapeforms.com Ph: 800.521.2546 Installation Guide INSTALLATION PROCEDURE: Bench ships fully assembled. Freestanding unit can be set in place. FOR EMBEDDED MOUNT: Turn bench upside down on protective surface. Remove four outer screws from glides as shown in Fig. 1. Leave glides installed. Install four threaded rods as shown in Fig. 2. Backed, 120in Backless, 70in Backless, 120in Backed, 70in Set unit in position and mark hole locations. Move unit aside. Included components (surface mount) Included components (embedded) Drill holes according to Fig. 3. Clear holes of debris. Set unit back in position, ensuring that threaded rods are not resting on the bottom of the hole. If necessary, move unit and drill holes deeper. Fill holes with adhesive to level recommended by adhesive manufacturer. Set unit in position. Wipe away excess adhesive before it cures. FOR SURFACE MOUNT: Turn bench upside down on protective surface. 4x – 5/8‐11 thread 4x – M6‐1 x 25mm 4x – M8 x 1.25 x 100mm Install surface mount bolts and set screws as shown in Fig. 4. Surface mt bolt Set screw Embedded threaded rod Set unit in position and mark hole locations.
- Page 2 Date: September 27, 2016 Bench Installation Guide www.landscapeforms.com Ph: 800.521.2546 Fig. 1 – Remove screws for threaded rod install Fig. 4 – Install surface mount bolts and set screws Fig. 2 – Install threaded rods SET SCREW SURFACE MOUNT BOLT DROP‐IN ANCHOR [127mm] (NOT INCLUDED) 5” MIN Fig. 3 – Embedded section detail for holes Fig. 5 – Surface mount bolt section view Page 2 of 2...
Need help?
Do you have a question about the FGP Series and is the answer not in the manual?
Questions and answers