Teleflex Marine SH 5210 Instructions

ll-eleflex
M A R I N E
640 North Lewis Road
Limerick, PA 19468 USA
61 0-495-701 1
www.teleflexmari ne. com
sH 521015215
BACK TOUilT RACK. HELT
TNSTRUGTIONS
Copyright I 998, Teleflex lncorporated (USA)
ALLER: THESE INSTRUCTIONS COltlTAlN IilPORTANT SAFETY lt{FORtATIOl{ AND ilUST BE FORWARDED TO
These instrudions describe how to install helm
assemblies for 'THE BACK MOUNT RACK' steering
system. Additionalcomponents
required to complete the
system are:
.
SC 134u, Cable (for single cable system)
.
SC 135n< Cable (for dual cable system)
.
SB 39526 Bezel Kit (Required to mount helm to
dash)
. Steering Wheel (max. dia. 16 in.- see Telefl€x
Catalog)
.
Engine Connection Kit (see Teleflex catalog)
Optional components are:
.
SB 2744810 degree Mounting Kit
.
SB 27449 20 degree Mounting Kit
.
SA39531 Torque Brake
NOTE: HELMS AND CABLE ASSEMBLIES ARE
SUPPLIED LUBRICATED READY FOR INSTALL-
ATION, DO NOT ADD ANY LUBRICANT TO EITHER
ASSEMBLY. USE OF OTHER LUBRICANTS CAN
CAUSE DAIVIAGE TO THE STEERING CABLE,
RESULTING IN THE CABLE SEIZING OR PRE-
MATURE WEAR. KEEP THE CABLE AND DRIVE
ASSEMBLY CLEAN DURING INSTALTATION. DIRT
WILL DAMAGE THE SYSTEM AND CAUSE
PREMATURE WEAR
,,r'r};
20
STEIiII{G ITIEEL
IINIIUT
fOUttlTlXG PL TE ILLOWS 20" FROI IIORIZO]|TTL
tt{ EtTHEn DtRlcTtox
FIGURE 1
IIISIDE FACE OF GUIIIIEL
7"*
9 ' / z i ' - > 1
I
|
' ' / :
cEilTqtxE_gE
rtE.ruc'-__
The Helm Assembly can be mounted for either port or
starboard cable entry. Steering cables, where possible,
should be routed to the starboard side of the boat to
balance engine torque.
PREPARATIO]I FOR I]ISTALLATIO]I
Stsp+- @ Helm Assemtily on
the dashboard.
CAUTTON: E/VSURE THAT THE CLEARANCES
SHOWN ON FIGURES 1 AND 2 ARE MAINTAINED.
ENSURE THAT THE STEERING WHEEL DOES NOT
INTERFERE WITH OTHER DASHBOARD EQUIPMENT
SUCH AS ENGINE COA'IROLS AND'NSTR UMENTS.
Step 2. Locate template in position selected. NOTE:
TEMPTATE FOR 20 DEGREE MOUNT DIFFERS
FROM TEMPTATE FOR 90 AND 10 DEGREE
MOUNTS. ENSURE THAT THE CORRECT ONE IS
USED. Drill one hole 2 /t" dlameter and 3 holes 5/16"
diameter.
WARI{ING
EEFORE STARTIITIG
INSTATLATION READ THESE IIiISTRUCTIONS
AND ENGII{E TAIGRS INSTRUCTIOI{S THOROUGHLY. FAILURE
TO FOLLOW E]THER OF THESE INSTRUCTIOIIIS OR INCORRECT
ASSEilBLY CAt{ RESULT IN LOSS OF CONTROL AND CAUSE
PROPERTY DATAGE OR II{JURY,
DO iIOT SUBSTITUTE PARTS FROT OTHER ITAIIUFACTURERS,
THEY MAY CAUSE A SAFETY HAZARD FOR WHICH TELEFLEX
IilC., USA CAI{}IOT ACCEPT RESPONSIBILITY.
TO AVOID EXCESSIVE STEERING LOADS, AI{D TO GET THE BEST
STEERITIG PERFORTAI{CE, THE OUTBOARD TIOTOR OR
OUTDRIVE TRIT TABS AND TILT POS]TIO]{ ]TIUST 8E ADJUSTED
AS INSTRUCTED
IN THE TIOTOR MANUFACTURERS
OPERATION
MANUAL. FAILURE TO DO SO CAI{ EFFECT THE PERFORTANCE
DO NOT ATTACH ANY ELECTRICAL GROUiID WIRES TO THE
HELM. THIS WOULD RESULT IltI AliI ELECTROLYTIC REACTION
TO THE STEERING CABLE THAT MAY RESULT IN CABLE
FAILURE OR GREATLY REDUCED SERVICE LIFE.
WARNING
i'UST NOT BE DISASSETBLED FOR
. FAILURE TO RE.ASSETIBLE CORRECTL
Y LEAD TO TOTAL FAILURE OF THE
COULD RESULT IN PERSONAL INJURY
7/98 Rev. 1 Page 1 of4 ts-sH5210/15