Advertisement
S&G
®
➥
d
e
c
eLetIng an
xIstIng
ode
The holder of the master code (position 0) can delete any other code.
The master code cannot be deleted under any circumstances.
The holder of the supervisor code (position 1) can delete user
codes. The supervisor code cannot be used to delete the master
code or itself.
Here is the process for deleting a supervisor code.
7 4 ✽
master code
To delete a user code in position 5, use the following sequence.
7 4 ✽
master code or supervisor code
To delete a time delay override code, see the time delay section.
m
t
d
anagIng
Ime
eLay
➥
c
, c
, d
reatIng
hangIng
eLetIng a
Time delay is a security feature that enforces a predetermined waiting
period between the entering of a valid lock code and the actual
opening of the lock. The delay period can be set from 1 to 99 minutes.
The opening window is a period of time immediately after the time
delay during which you can enter a valid lock code to open the lock.
The factory default opening window is 2 minutes, but it can be
changed to any value between 1 and 10 minutes.
Note: Changes to an existing time delay or opening window can only be
accomplished during the opening window period. This means you must enter
a valid operating code for the lock, wait for the time delay to expire, then
begin the appropriate programming sequence rather than opening the lock.
The programming sequence for setting, changing, or deleting a
time delay period is as follows. The period can be anywhere from
1 to 99 minutes.
7 4 ✽
master code
length of desired time delay period
To delete a time delay, enter 0 for the desired time delay length.
© Copyright 2006, Sargent & Greenleaf
O
perating
Z
D-Drive
03
™
♪ ♪ ♪ ♪ ♪
♪ ♪ ♪
♪ ♪ ♪
♪ ♪ ♪
#
1 #
#
#
♪ ♪ ♪ ♪ ♪
♪ ♪ ♪
♪ ♪ ♪
#
5 #
#
t
d
Ime
eLay
♪ ♪ ♪ ♪ ♪
♪ ♪ ♪
#
0 0 #
♪ ♪ ♪
#
length of desired time delay period
i
nstructiOns
Multi-User Electronic Safe Lock
2005 Series
➥
c
hangIng the
The length of the opening window period is set as follows. The period
can be anywhere from 1 to 10 minutes.
➥
m
anagIng
This optional feature determines whether or not you can override the
time delay waiting period. There may be special circumstances that
♪ ♪ ♪
make it desirable to open the lock before time delay expires, such as
#
during cash pickups by an armored car service. Time delay override
only works when the lock is being operated in time delay mode. Your
lock is capable of two different types of time delay override. Single
control time delay override allows the TDO code holder to simply enter
his code to open the lock. The delay period is completely bypassed.
The other type of time delay override is dual control TDO. To use this
type of time delay override, it is necessary to start the lock's time
delay by entering any valid code other than the TDO code. Then, within
one minute, enter the TDO code. The lock will open immediately. This
type of time delay override places a secondary control on the TDO
code holder, adding a measure of extra security.
➥
t
s
urnIng
If your lock was ordered with time delay override capability, single
control TDO can be turned on as follows.
➥
t
d
urnIng
If your lock was ordered with time delay override capability, dual
control TDO can be turned on as follows.
♪ ♪ ♪
#
➥
t
t
urnIng
Ime
When time delay override is turned off, the time delay override
code is erased. PIN position #9 can now be used to store a
regular user code.
Page 5
o
W
d
penIng
IndoW
uratIon
♪ ♪ ♪ ♪ ♪
7 4 ✽
#
master code
length of desired opening window period
length of desired opening window period
t
d
o
Ime
eLay
verrIde
c
t
d
o
IngLe
ontroL
Ime
eLay
verrIde
♪ ♪ ♪ ♪ ♪
4 6 ✽
#
master code
c
t
d
o
uaL
ontroL
Ime
eLay
verrIde
♪ ♪ ♪ ♪ ♪
4 6 ✽
#
master code
d
o
off
eLay
verrIde
♪ ♪ ♪ ♪ ♪
4 6 ✽
#
master code
♪ ♪ ♪
0 1 #
♪ ♪ ♪
#
♪ ♪ ♪
#
on
♪ ♪ ♪
♪ ♪ ♪
2 #
2 #
on
♪ ♪ ♪
♪ ♪ ♪
1 #
1 #
♪ ♪ ♪
♪ ♪ ♪
0 #
0 #
Advertisement
