Advertisement
Quick Links
TM
SAGITTILT
PRONE
BREAST SOLUTION
STORAGE CART
Article No. : 32070/900
A. GENERAL PRODUCT INFORMATION
The product referred to in this document is a
storage system for medical devices, used for
patient positioning and immobilisation in radiation
therapy.
This product may only be used in combination with
Orfit immobilisation products. Orfit prohibits the
use of unauthorised third-party products in
conjunction with its own products.
B. PRODUCT DESCRIPTION
This storage cart is used to store the Sagittilt
Prone Breast Solution in an upright position.
Information on these other parts (and instructions
on how to make the masks) can be found in the
respective 'instructions for use' and on
www.orfit.com.
C. PARTS LIST
The storage cart contains the following parts:
ART. NO.
DESCRIPTION
32070/900
4 wheels
containing:
2 vertical frames
1 bottom frame
1pivoting
mechanism
1 centre axis
2 side pockets
1 storage tray
1 bag of screws
1 set of tools
Figure 1
D. INSTALLATION
STEP 1: Packaging
TM
Unpack all the items and verify if you have all the
necessary products described in the parts list in the
previous paragraph.
STEP 2: Mounting of vertical frames
Attach the 2 vertical frames to the bottom frame.
Make sure the black buttons are facing inwards,
towards each other.
PART(see
picture below)
1
2
3
4
5
6
7
Figure 2
8
9
Page 1 of 8
INSTRUCTIONS FOR USE
Advertisement
Summary of Contents for orfit SAGITTILT 32070/900
- Page 1 This product may only be used in combination with Orfit immobilisation products. Orfit prohibits the use of unauthorised third-party products in Figure 1 conjunction with its own products.
- Page 2 Figure 3 STEP 3: Mounting of the wheels Turn the structure upside down so the device is Figure 6 resting on the vertical frames and the bottom frame STEP 4: Mounting of the pivoting mechanism is facing upwards. Take both screws out of the center axis of the pivoting mechanism with the use of an Allen wrench.
- Page 3 Figure 9 Figure 11 STEP 5: Mounting of hydraulic hinge Place the large and small frame horizontally. Attach the screw again to the center axis by screwing it into the top hole of the vertical frames on both sides. Figure 12 Push the black hydraulic hinges of the short frame onto the black buttons on the vertical frames.
- Page 4 Now place the large frame vertically. Figure 16 STEP 6: Mounting of the center axis Unscrew the screws on both sides of the center axis. Figure 14 Push the black hydraulic hinges of the long frame Figure 17 onto the black buttons on the vertical frames. Match the numbers on the hinges with the ones on Attach the center axis to the vertical frames and the frame (number 5 and 6).
- Page 5 Position the first side pocket on one side of the side of the storage cart you position the deep or vertical frame and insert the 2 screws. Use one the shallow side pocket. washer on the inside and one washer on the outside STEP 8: Mounting of the storage tray of the frame.
- Page 6 Use the 4 long screws provided to attach the picture below or on the widest part of the top storage tray. Each screw should be combined with frame. 1 nut, 1 washer on the inside of the tray and 1 washer on the outside.
-
Page 7: Precautions For Use
Push the short frame downwards. Push the frame into a vertical position again. Figure 31 Figure 28 Now place the long frame horizontally so you can slide the caudal piece of the Sagittilt on top of it. Make sure the treatment table is at the same height as the storage cart. -
Page 8: Additional Information
Note: The instructions were written in accordance with the European Directive 93/42/EEC for Medical Devices. It is prohibited to make alterations to this text without prior approval from Orfit Industries. SAGITTILT™ is a trademark of Orfit Industries www.orfit.com...