Related Manuals for SUNRICH TECHNOLOGY N-590
Summary of Contents for SUNRICH TECHNOLOGY N-590
- Page 1 PCIe 4-Port Gigabit Server Adapter with LAN Bypass User Manual Ver. 1.00 All brand names and trademarks are properties of their respective owners.
-
Page 2: Table Of Contents
Contents: Chapter 1: Introduction ............3 1.1 Product Introduction ............ 3 1.2 Features ................ 4 1.3 System Requirements ..........4 1.4 Package Contents ............4 Chapter 2: Getting Started ..........5 2.1 Hardware Installation ..........5 2.2 Driver Installation for Windows ........5 2.3 Driver Installation for Linux ........ -
Page 3: Chapter 1: Introduction
Chapter 1: Introduction 1.1 Product Introduction PCI Express is the next revolution in I/O interconnect standards that will deliver the bandwidth and features required by PCs, consumer electronics and communications devices. The architecture is a cost-effective, low-pin count, and point-to-point technologies offering maximum bandwidth, reducing cost and design complexity and enabling smaller form factors. -
Page 4: Features
1.2 Features ⚫ Four 10/100/1000Mbps compatible RJ-45 Ethernet ports ⚫ Four-lane (or x4) PCI Express compatible with x4, x8 and x16 PCI Express slots ⚫ Fully Compliant with IEEE 802.3, IEEE 802.3u, IEEE 802.3ab ⚫ Supports 10/100/1000M data auto-negotiation ⚫ Up to 9KB Jumbo frames ⚫... -
Page 5: Chapter 2: Getting Started
⚫ 1 x Driver CD ⚫ 1 x User Manual Chapter 2: Getting Started 2.1 Hardware Installation Turn off the power to your computer. Unplug the power cord and remove your computer’s cover. Remove the slot bracket from an available PCIe slot. To install the card, carefully align the card’s bus connector with the selected PCIe slot on the motherboard. - Page 6 Insert the provided CD into your disk drive. The CD-ROM will start automatically. The following screen will show up and please click “Install Driver”. *Note: Actual image may vary Note: If the install program doesn’t run automatically, please locate and double-click on the Autorun.exe file in the CD to launch the install program.
-
Page 7: Driver Installation For Linux
2.3 Driver Installation for Linux Insert the provided CD into your CD-ROM drive. Extract the compressed driver source file to a certain directory by the following command: (Please copy the driver file “igb-5.3.5.18.tar.gz” from the CD folder “.\ Driver\Intel\PRO1000\LINUX” to a certain folder on hard drive) # tar zxf igb-<x.x.x>.tar.gz Change to the driver src directory, where <x.x.x>... -
Page 8: Verifying For Linux
Entry “Network adapters” item, and you can read “Intel(R) I350 Gigabit Network Connection” in the Device Manager. 2.4.2 Verifying for Linux You can check whether the driver is loading by using following commands: # lsmod | grep igb # ifconfig –a MN5000000071 Page 8... -
Page 9: Chapter 3: Troubleshooting Tips
If there is a device name, ethX, shown on the monitor, the linux driver is load. Then, you can use the following command to activate the ethX. # ifconfig ethX up, where X=0,1,2,… Chapter 3: Troubleshooting Tips ⚫ The computer can NOT detect the PCIe Dual Port Gigabit Server Adapter Make sure that the PCI Express card is correctly plugged into the PCI Express slot;... - Page 10 the advanced supporting for BIOS updated. The board itself might be defective. You can try another motherboard testing PCIe Dual Port Gigabit Server Adapter working or not. ⚫ Computer failed to start after inserting the PCIe Dual Port Gigabit Server Adapter Turn off the computer, remove the PCIe Dual Port Gigabit Server Adapter, and try to restart the computer.
Need help?
Do you have a question about the N-590 and is the answer not in the manual?
Questions and answers