Advertisement
Contents
1.
Removing the transport lock ...................................................................................... 2
2.
Windshield with Rain cover ........................................................................................ 3
3.
Windshield with Fur ................................................................................................... 3
4.
Connection of the windshield .................................................................................... 4
5.
Orientation of the windshield ..................................................................................... 5
6.
Channel allocation ..................................................................................................... 6
7.
Changing from Fur to Rain Cover ............................................................................... 7
ORTF-3D Windshield
with Rain Cover or Fur
Setup Guide, 15.07.2019
Page 1 of 10
SCHOEPS ORTF-3D Windshield
with Rain Cover or Fur
Setup Guide
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Schoeps ORTF-3D
-
Page 1: Table Of Contents
SCHOEPS ORTF-3D Windshield with Rain Cover or Fur Setup Guide ORTF-3D Windshield with Rain Cover or Fur Setup Guide, 15.07.2019 Contents Removing the transport lock ..................2 Windshield with Rain cover ..................3 Windshield with Fur ....................3 Connection of the windshield ..................4 Orientation of the windshield .................. -
Page 2: Removing The Transport Lock
SCHOEPS ORTF-3D Windshield with Rain Cover or Fur Setup Guide 1. Removing the transport lock The ORTF-3D windshield is often shipped with a transport lock installed, as this prevents from damages in long oversea shipping when the elastic suspensions are overly stressed. -
Page 3: Windshield With Rain Cover
Important: The heating of the ORTF-3D setup should be on all time to dry out the fabric, but at least two hours before use. It is recommended to regularly check the wetness of the setup when installed permanently. -
Page 4: Connection Of The Windshield
SCHOEPS ORTF-3D Windshield with Rain Cover or Fur Setup Guide 4. Connection of the windshield If rain cover is installed: To connect the setup, open the top foam lid on one side by opening the Velcros. The metallic mounting cylinder with the eye bolts does not need to be uninstalled. -
Page 5: Orientation Of The Windshield
SCHOEPS ORTF-3D Windshield with Rain Cover or Fur Setup Guide 5. Orientation of the windshield The front of the setup is marked by a label on the cable. Orient the windshield in the direction of this cable outlet. Page 5 of 10... -
Page 6: Channel Allocation
The cable outlets of the windshield are marked with “Top” and “Bottom” which corresponds to the two layers of the ORTF-3D technique. 4ch Multicore breakout cable Channel Allocation of the ORTF-3D Setup Channel # Labelling Channel routing on the... -
Page 7: Changing From Fur To Rain Cover
SCHOEPS ORTF-3D Windshield with Rain Cover or Fur Setup Guide 7. Changing from Fur to Rain Cover This step-by-step instruction explains how the fur can be replaced by the rain protection. Step 1: Unscrew the eye bolts Step 2: Open the fur:... - Page 8 SCHOEPS ORTF-3D Windshield with Rain Cover or Fur Setup Guide Step 5: Close the Velcros: Step 6: Before installing the black rubber lid, tighten the connectors with the Velcros in the middle: Page 8 of 10...
- Page 9 SCHOEPS ORTF-3D Windshield with Rain Cover or Fur Setup Guide Step 7: Connect the Multicores. Remember which Multicore connects to the Lower channel connector and which to the upper channel connector. Step 8: Install the black rubber lid: Step 9: Install the rain cover cap:...
- Page 10 SCHOEPS ORTF-3D Windshield with Rain Cover or Fur Setup Guide Step 10: Install the metallic mounting cylinder and tighten the counter nut: Page 10 of 10...
Need help?
Do you have a question about the ORTF-3D and is the answer not in the manual?
Questions and answers