Advertisement
4.4.
Operation
WARNING! DO NOT switch on the saw whilst the disc is in contact with the workpiece. Bring the rotating disc to the workpiece.
!
4.4.1. The cutting disc must be running at maximum speed before attempting to lower the cutting edge onto the workpiece.
4.4.2. Lower the cutting disc slowly and smoothly down toward the workpiece (avoid jerky movements).
4.4.3. Avoid subjecting the disc to excessive strain. Always ease the disc down against workpiece (a harsh downward impact may cause
disc failure) and do not apply undue force on the handle when cutting the workpiece. Maintain a controlled cutting speed.
4.5.
Completing the cut
4.5.1. When cutting is complete, fully raise the cutting disc and release the On/Off switch.
4.5.2. Wait until the disc has stopped rotating before attempting to remove the workpiece.
4.6.
Mitre cutting
To cut the workpiece at an angle the base of the saw must be adjusted.
4.6.1. To make an angled cut, loosen the vice back plate retaining bolts (fig. 4.A) and turn the turntable to
the required angle, reading the graduated scale around the perimeter of the vice back plate.
4.6.2. Re-tighten the retaining bolts and make the cut.
5. CHANGING CUTTING DISC
% DANGER! The use of damaged discs is dangerous and may cause injury.
! WARNING! Ensure that the saw is unplugged from the power supply before attempting to
change the cutting disc.
Before using a cutting disc ensure that there are no fissures or cracks in it. Once mounted on the saw
test the disc before use by facing the saw in a safe direction (turned away from yourself, others and
vulnerable items) and running it for a short time.
IMPORTANT! Cutting discs used with this machine shall be of an adequate speed rating and
suitable for the task in hand. Only persons qualified under the "Abrasive Wheels Regulations" and holding a current grinding wheel
certificate are to change cutting discs.
5.1.
Removing disc
5.1.1. With the head in the up position rotate the disc guard until the handle engages with the slot
in the fixed guard (fig. 5.A).
5.1.2. Loosen the centre guard clamp screw (fig. 5.B) and swing the centre guard (fig. 5.D) down.
5.1.3. Place the holding tool in the spindle hole (hole is located on the motor side of the disc, see fig. 6).
5.1.4. Use the spanner to remove disc clamp bolt (fig. 5.C).
5.1.5. Carefully remove the disc and clamping parts.
5.1.6. Clean parts before re-assembly.
5.2.
Fitting disc (fig. 6)
WARNING! Read Section 1 safety instructions to ensure disc fitting requirements are followed.
5.2.1. Fit the inner flange (2) checking to ensure that it seats correctly on the spindle (1).
Fit the disc and items 3,4 & 5 to the spindle.
5.2.2. Fit and tighten the locking bolt (6).
5.2.3. Before plugging the saw into the mains, move the disc guard back to the closed position so
that the disc is covered.
5.2.4. Check that the guard is working properly by raising and lowering the operating head.
6. MAINTENANCE
WARNING! Ensure that the saw is unplugged from the power supply before attempting
!
any maintenance.
6.1.
Regularly clean the dust which accumulates inside the protective guard and on the external parts.
6.2.
Periodically clean and oil the vice screw.
6.3.
Change the abrasive disc when it is worn and does not operate efficiently.
6.4.
To change the motor brushes removed the brush caps with a screwdriver (fig. 7). Replace the
carbon brushes and re-install the brush caps.
7. DECLARATION OF CONFORMITY
Abrasive Disc Cut-Off Saws
Models MG214/230V.V2 & MG214/110V.V2
73/23/EEC Low Voltage Directive
89/336/EEC EMC Directive
98/37/EC Machinery Directive
93/68/EEC CE Marking Directive
2002/95/EC RoHS Directive
2002/96/EC WEEE Directive
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this equipment.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our catalogue and latest promotions call us on 01284 757525 and leave your full name, address and postcode.
01284 757500
Declaration of Conformity
are in conformity with the following standards and directives.
Signed by Mark Sweetman
The construction files for these products are held by the Manufacturer and may be inspected, by a national authority,
upon request to Jack Sealey Ltd.
For Jack Sealey Ltd. Sole importer into the UK of Sealey Quality Machinery.
Sealey Group,
Bury St. Edmunds, Suffolk.
01284 703534
We, the sole importer into the UK, declare that the products listed here
sales@sealey.co.uk
e-mail
fig. 4
A
fig. 6
6th August 2007
www.sealey.co.uk
Web
MG214/230V.V2 & MG214/110V.V2 - 2 - 060807
fig. 5
fig. 7
Advertisement
