1. Manuals
  2. Brands
  3. PERFECTPASS Manuals
  4. Boating Equipment
  5. StarGAZER WAKE edition
  6. Manual

PERFECTPASS StarGAZER WAKE edition Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
StarGazer - Wake Edition
Mechanical
January 2016
6/7/2016

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the StarGAZER WAKE edition and is the answer not in the manual?

Questions and answers

Related Manuals for PERFECTPASS StarGAZER WAKE edition

Summary of Contents for PERFECTPASS StarGAZER WAKE edition

  • Page 1 StarGazer - Wake Edition Mechanical January 2016 6/7/2016...

  • Page 2: Table Of Contents

    Table of Contents Page No. Section 1 Using StarGazer Wake Edition Wakeboard Speed Mode Setting KDW Section 2 Using RPM Mode Section 3 Using Slalom Mode Course Timing (No Mag Timing) Section 4 Using Name List Section 5 Other Display Features...

  • Page 3: Using Stargazer Wake Edition

    Section 1 Initial System Start Up The very first time your PerfectPass is turned on, it may ask you two questions: 1. “Initial Hours 000”. If this hour meter feature is present, use the UP Key to enter the number of hours on your boat. PerfectPass will start counting from that position.

  • Page 4: Setting Kdw

    DRIVING TIP: Some boats have an overly strong return spring that causes the handle to pull back on its own. (This will result in PerfectPass disengaging). In this case you will need to keep your hand on the lever or talk to your dealer about a way to make the...

  • Page 5: Using Rpm Mode

    Section 2 RPM Mode USING RPM MODE In this mode, the screen will appear as follows: 2. Menu Arrow 1. SETPOINT Speed Base Mode Indicator Speed Tachometer Operating in this mode is very similar to using the Wakeboard mode, except the system is now controlling to an RPM SETPOINT.

  • Page 6: Using Slalom Mode

    Section 3 Slalom Mode 1. Select Slalom Mode. Simply set your speed and go. 2. If you wish to time your passes in a slalom course, you must “MAP” the course. 3. You can select speeds in 1 mph (1.5 kph) increments. The official speeds in MPH are: 24.9, 26.7, 28.6, 30.4, 32.3, 34.2, 36.0 4.
  • Page 7 UP Key at DOWN Key at Entrance in opposite Entrance direction (Entry 2) (Entry 1) Note: Only the entrance gates from each direction will be “mapped”. Step. 3 Starting at one end of the course, idle the boat towards and through the entrance gates.

  • Page 8: Using Name List

    The features available vary depending on the make and model of your boat. If a feature is not present on your PerfectPass then it is not available on your system. To move to the next feature press the MENU key.

  • Page 9: Other Display Features

    CONTROL SETTINGS – Applicable to “Drive by Wire” systems only. DEVICE TEST – Here you can check the Servo Motor and Wiring. (See Servo Motor Phase Test under “Troubleshooting” at www.perfectpass.com and associated video. USER SETTINGS – Switch between MPH<>KPH. You can also select Engine Type (V8<>V6) and RPM Inversion.

  • Page 10: Driving Tips

    Always pull a rider up smoothly. If you accelerate too far past the target speed, you can gently pull the throttle handle back to assist PerfectPass in taking control. When PerfectPass engages you will hear an audible “beep”. In addition when engaged the Modes (Wakeboard) or Name on Screen will become highlighted.

  • Page 11: Troubleshooting

    “hunts” above & below Set Speed. Solution: It appears that the PerfectPass throttle cable does not have free movement and is rubbing against engine cover or some other obstacle. A Linkage Test should be performed. See Page 11.
  • Page 12 (Remember, resistor & servo motor will run very hot which is normal). Condition: Speed in Slalom mode not accurate. Solution: You must calibrate each speed. See Page 4 for details or contact PerfectPass for assistance. Condition: Set in KPH but want MPH Solution: Press Menu and UP Keys together.

  • Page 13: System Reset

    Servo Motor Test / Auto Tighten Test Every time you return the boat to neutral when PerfectPass is on, the servo will wind in the cable until snug in a clockwise direct. This is the normal starting point for the servo.

  • Page 14: Installation

    10/32 nut is in place on Morse control / Teleflex throttle cable. Screw threaded brass hex connector on the PerfectPass cable onto the end of the Morse control throttle cable. (Do not over tighten hex nut). Install L shaped brass throttle adapter to throttle control lever using identical hole as original ball joint.
  • Page 15 Step 3. Mount Dash Display Remove the speedometer (if boat has two speedometers, remove the right unit) and install the In Dash PerfectPass Display and connect into Master Module. (If there is a speedo tube on back, it should be clamped).
  • Page 16 The black wire can be securely connected to any suitable ground. LT-R / LT-1 - On this engine the Gray wire lead on the PerfectPass RPM Sensor cable is not used and can be taped off. The separate Black wire end must be connected to the Gray wire located in the main wiring harness leading into the Borg Warner MDC Control box.

  • Page 17: Gps Receiver

    Step 8. GPS RECEIVER INSTALLATION Installation: The GPS Receiver can be installed on the dash board looking up through the wind screen. As long as the receiver has a clear unobstructed view of the sky, it will work properly, even if sitting at an angle to the sky. (It can also be installed under the dash looking up through the fiberglass.
  • Page 18 The PerfectPass Speed Control device should not be used for any other purpose or under any other conditions.
  • Page 19 “technical support” as many issues may be easily handled direct with customer. 2. If your PerfectPass was purchased and installed by a dealer you may contact your dealer direct or initiate a warranty claim with PerfectPass.

Table of Contents