Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for MED Associates PHM-104A
- Page 1 HIGH/LOW SPEED PRECISION PUMP PHM-104A USER’S MANUAL DOC-187 Rev. 1.6 Copyright ©2019 All Rights Reserved Med Associates, Inc. P.O. Box 319 St. Albans, Vermont 05478 Phone: 802.527.2343 Fax: 802.527.5095 www.med-associates.com...
- Page 2 This page intentionally left blank...
-
Page 3: Table Of Contents
USB Control Via MED-PC ......................10 Sample MED-PC Program ......................12 28-V Output Via MED-PC ......................15 Chapter 4 | PHM-104A Driver and Software Installation ........16 Appendix A | Contact Information ................18 - iii - DOC-187 Rev. 1.6 Copyright © 2019... - Page 4 M E D A S S O C I A T E S , I N C . PHM-104A HIGH/LOW SPEED PRECISION PUMP Notes _____________________________________________________________________________________ _____________________________________________________________________________________ _____________________________________________________________________________________ _____________________________________________________________________________________ _____________________________________________________________________________________ _____________________________________________________________________________________ _____________________________________________________________________________________ _____________________________________________________________________________________ _____________________________________________________________________________________ _____________________________________________________________________________________ _____________________________________________________________________________________ _____________________________________________________________________________________ _____________________________________________________________________________________ _____________________________________________________________________________________ _____________________________________________________________________________________ _____________________________________________________________________________________...
-
Page 5: Chapter 1 | Introduction
A wide range of injection rates is possible, as well as unprecedented injection speeds. For example, an injection volume of 100 µl can be delivered in less than 100 ms using a 500-µl syringe. The PHM-104A also allows the entire syringe volume to be injected in a single infusion. The pump can be controlled using MED-PC or the included software. -
Page 6: Chapter 2 | Pump Overview
Enables the MED OPERATE connector. When the switch is in TEST position: Completes one infusion at the default pump settings (refer to Table 3.1 - PHM-104A Control Software User Interface, Set Default). NOTE: These switch positions do not function when the pump is connected to the computer via the USB connector. - Page 7 P H M - 1 0 4 A H I G H / L O W S P E E D P R E C I S I O N P U M P Figure 2.2 – Manifold End of the PHM-104A Figure 2.3 - Control End of the PHM-104A...
-
Page 8: Dose Capabilities
P H M - 1 0 4 A H I G H / L O W S P E E D P R E C I S I O N P U M P Dose C apabilities Figure 2.5 - Figure 2.7 display the PHM-104A infusion capabilities for 10 uL, 100 uL and 500 uL syringes, respectively. Infusion rates are dependent upon the size of the syringe and the dose volume. The minimum infusion rate for all three syringe sizes equals 10% of the syringe volume. - Page 9 P H M - 1 0 4 A H I G H / L O W S P E E D P R E C I S I O N P U M P Figure 2.6 – PHM-104A Pump Dose Capabilities 100 uL...
-
Page 10: Chapter 3 | Operating Instructions
When removing a loaded syringe, be sure to grasp the syringe firmly as indicated in Figure 3.2 and lift straight up. Improper removal of the syringe may result in damage to the syringe and/or pump apparatus. Figure 3.2 - Correct Removal of a Loaded Syringe - 6 - DOC-187 Rev. 1.6 Copyright © 2019 Med Associates, Inc. -
Page 11: Hardware Setup
Connect a section of tubing of the required length to the Input port on the manifold, shown in Figure 2.2 – Manifold End of the PHM-104A, using a female luer connector. Submerge the other end of the section of tubing in the infusion solution. -
Page 12: Software Controlled Operation
Application. Refer to | PHM-104A Driver and Software Installation for driver and software installation instructions. Using the 24 VDC (2.5 amp) power supply, connect the 24 VOLTS connector on the PHM-104A to a standard wall outlet. Using the included USB cable, connect the USB port on the PHM-104A to the USB port on the computer that was used for driver installation. - Page 13 Select the desired pump to view/change infusion settings. Sets the Syringe, Dose, and Rate values to the pump’s default values and causes the PHM-104A Control Application to recognize any pumps that have been connected to the computer after the application Reset was opened.
-
Page 14: Med-Pc Controlled Operation
Syringe Loaded. (The pump ID corresponds to the Box in MED-PC). Set the FLUSH/REMOTE/TEST switch to REMOTE. Using the 24 VDC power supply, connect the 24 VOLTS connector on the PHM-104A to a standard wall outlet. Turn the PHM-104A on using the green ON/OFF switch. - Page 15 P104A_Init(MG) Syntax: ~P104A_Init(MG);~ Where: MG = MED-PC Global Parameter. Comments: Initializes the PHM-104A pump. Must be used at beginning of program. This command only needs to be executed once. Example: #START: ~P104A_Init(MG);~ ---> S2 P104A_PumpSetup(MG, BOX, P1, P2, P3, P4, P5) Syntax: ~P104A_PumpSetup(MG, BOX, P1, P2, P3, P4, P5);~...
-
Page 16: Sample Med-Pc Program
It allows the PHM-104A to pass back information about any errors that might have occured. \ BOX - This parameter specifies which PHM-104A the command is for. When this program is running in Box 1, then the BOX parameter will equal 1 and the PHM-104A that is set to Node 1 will receive the command. - Page 17 P H M - 1 0 4 A H I G H / L O W S P E E D P R E C I S I O N P U M P PHM-104A that is set to Node 2 will receive the command, etc.
- Page 18 P H M - 1 0 4 A H I G H / L O W S P E E D P R E C I S I O N P U M P \*************************************************** PHM-104A PUMP Schedule S1 - Set Default Values...
-
Page 19: 28-V Output Via Med-Pc
This section describes the procedure for using a MED-PC 28-Volt output to turn the pump on and off. The pump will operate using the default parameters. Using the 24 VDC power supply connect the 24 VOLTS connector on the PHM-104A to a standard wall outlet. -
Page 20: Chapter 4 | Phm-104A Driver And Software Installation
PHM-104A is connected to a different USB port at a later time. Insert the PHM-104A CD into the CD-ROM drive and the screen shown in Figure 4.1 – PHM-104A Main Screen will appear. Click Install the PHM-104A High-Low Speed Pump Software and the screen shown in Figure 4.2 will appear. - Page 21 Using the 24 VDC power supply, connect the 24 VOLTS connector on the PHM-104A to a standard wall outlet. Using the included USB cable, connect the USB port on the PHM-104A to any available USB port on the computer. The Found New Hardware Wizard screen will appear.
-
Page 22: Appendix A | Contact Information
P H M - 1 0 4 A H I G H / L O W S P E E D P R E C I S I O N P U M P APPENDIX A | CONTACT INFORMATION Please contact Med Associates, Inc. for information regarding any of our products. For Technical questions, email support@med-associates.com.
Need help?
Do you have a question about the PHM-104A and is the answer not in the manual?
Questions and answers