Renfert Magma 2300-0000 Instruction Manual
Hide thumbs
Also See for Magma 2300-0000:
- Instruction manual (196 pages) ,
- Repair manual line (28 pages)
Related Manuals for Renfert Magma 2300-0000
Summary of Contents for Renfert Magma 2300-0000
- Page 1 Magma Nr. 2300-0000 /-0500 /-3000 /-3500 Ideas for dental technology Made in Germany...
-
Page 7: Table Of Contents
Magma No. 2300-0000 /-0500 /-3000 /-3500 ENGLISH Content Introduction ............Delivery Versions ........Symbology ............10. Accessories ..........Information for Operators ........ 11. Error List........... Operating Instructions Information for Operators Setup and Commissioning ....... Application Area ........1.1 Installing the Handle ........26 A.1 Proper Use ............. -
Page 8: Information For Operators
Information for Operators Only intended for indoor use. Using these operating instructions as a Before opening the unit, disconnect it from starting point, instruct all operators of the the mains power supply by unplugging the unit with regard to the area of application, power cord from the wall outlet. -
Page 9: Curing
1.5 Curing Programme LED: The oven has already been cured at the factory du- LED flashing: ring manufacturing. Programme being copied (refer to Sec. 4.3) This can be determined by the discolouration around LED continuously on: the door panel, the ceramic in the oven and the door Input modifications have not yet been saved. -
Page 10: Setting The System Date / Time
2.3.1 S If the signal generator was previously on, it is ETTING THE YSTEM now off: The following sequence is used to set the system S : OF and a brief sound. Lower display: date / time: If the signal generator was previously off, it is Year - Month - Day - Hour - Minute. -
Page 11: Speed Programming Simple Heating Processes
3. Speed Programming 6. Press the Start/Stop key – start the speed pro- gramme Simple Heating Processes The casting time is displayed (for approx. 2 sec.): The speed programme is indicated by the programme Date number „P_ _“. Time The speed programme includes only the increase and holding phases for stage 4. -
Page 12: Programming
4. Programming As soon as you modify a value the pro- The Magma preheating oven gives you the option of gramme LED goes on to indicate that va- creating and saving heating programmes. lues have been modified and can be saved. You can store up to 99 different heating programmes 3. -
Page 13: Copying Heating Programmes
4.3 Copying Heating 5. Operating the Oven Programmes • Place the ceramic slab (B, Fig. 5) into the furnace with the arrows pointing towards the rear wall and Copying an existing heating programme allows you to push the slab fully to the rear. quickly and easily create new, similar heating pro- Always use the ceramic pad when opera- grammes. -
Page 14: Start The Heating Programme
5.2 Start the Heating Programme • You exit the casting time input mode by pressing the ESC key; 5.2.1 W ITHOUT A ROGRAMMED ASTING • You press the ESC key in the normal display; • You start and then stop the heating programme. •... -
Page 15: Modifying Parameters During A Heating Programme
• “P” key: 5.4 Ending a Heating Programme Upper display: A heating programme can be prematurely cancelled Holding temperature of the last programmed at any time with: stage in the current programme. Lower display: Number of the current programme. If it is not prematurely cancelled it automatically ends Heating phase LEDs for those phases for which once the holding time in the last programmed stage a value has been saved are continuously on. -
Page 16: Catalyser
A catalyser can be connected to the oven (refer to the on and off by the operator during a heating program- accessories). The controller automatically detects the presence of a connected Renfert catalyser. • To switch the catalyst converter on: 5.6.1 M... -
Page 17: Cleaning / Maintenance
6. Cleaning / Maintenance 5. Disconnect the cable (Figure 9). 6. Pull the thermocouple straight out, towards the Only perform cleaning and maintenance if rear (Figure 10). the oven is cold! 7. Insert a new thermocouple into the oven, making Use a soft, moist cloth and cleanser to clean the sure it is straight (Figure 10). -
Page 18: Backup Battery Replacement
6.6 Backup Battery Replacement 7. Spare Parts Refer to the spares list at the end of this manual for 1. Switch the oven off and unplug the power cord at numbers of wearing and replacement parts. the wall outlet. 2. Allow the oven to cool off. 3. -
Page 19: Error List
11. Error List Error Possible cause Corrective action Displays remain blank • Power cord not plugged in. • Plug the power cord into the wall outlet. after the oven is swit- • Building fuse blown. • Check the building fuse and replace, as re- ched on at the main quired. -
Page 20: Information For Operators
Error Possible cause Corrective action Err 7 • Faulty thermocouple. • Replace the thermocouple (refer to Sec. 6.4). • Oven cooled with compressed • Allow the oven to cool off. air and heating programme started (temperature increase due to the heat retained in the oven). -
Page 21: Hazard And Warning Information
B. Hazard and Warning An “Err” display may indicate an overhe- Information ating of the oven. Do not touch the oven. Burn hazard! Only intended for indoor use. The unit is Switch the oven off at the main power only designed for dry applications and may switch and allow it to cool off. -
Page 22: Preparations Prior To Starting
The product is repaired by other than an autho- F.1.1 D EU M ISPOSAL NSTRUCTIONS FOR EMBER rized facility or if any but Renfert OEM parts are employed; ATIONS To conserve and protect the environment, prevent • The product continues to be employed, despite environmental pollution and improve the recycling of obvious safety faults or damage;...
Need help?
Do you have a question about the Magma 2300-0000 and is the answer not in the manual?
Questions and answers