Subscribe to Our Youtube Channel
Related Manuals for nvent SCHROFF 11850-016
Summary of Contents for nvent SCHROFF 11850-016
- Page 1 User Manual 1 U MTCA Shelf Product Number: 11850-016 February 2016 Doc-No: 63972-350_R1.0...
- Page 2 R1.0 February 2016 Initial release Impressum: Schroff GmbH Langenalber Str. 96 - 100 75334 Straubenhardt, Germany The details in this manual have been carefully compiled and checked - supported by certified Quality Management System to EN ISO 9001/2000 The company cannot accept any liability for errors or misprints. The company reserves the right to amendments of technical...
-
Page 3: Table Of Contents
11850-016 Safety ........................1 Safety Symbols used in this document................1 General Safety Precautions ....................1 References and Architecture Specifications..............1 Hardware Platform ....................2 Front and Rear View......................3 ESD Wrist Strap Terminal ....................3 Backplane ......................... 4 Backplane Topology ......................4 Fabric Interface ......................... - Page 4 11850-016 R1.0, February 2016...
-
Page 5: Safety
11850-016 1 Safety The intended audience of this User’s Manual is system integrators and hardware/software engineers. 1.1 Safety Symbols used in this document Hazardous voltage! This is the electrical hazard symbol. It indicates that there are dangerous voltages inside the Shelf. -
Page 6: Hardware Platform
11850-016 2 Hardware Platform The Schroff 11850-016 is an 1 U/2slot MicroTCA Shelf with EMCH (Embedded MicroTCA Carrier Hub) for AMC Single Full-size or Mid-size modules (with 2 HP filler panel). Features: • Shielded steel case • 2 AMC single Full-size slots •... -
Page 7: Front And Rear View
11850-016 2.1 Front and Rear View Figure 1: Front and RearView ESD Wrist Strap Terminal EMCH interfaces 2 HP Filler panel Ground Terminal (Equipotential bonding) AC input Mains/line switch EMCH 2.2 ESD Wrist Strap Terminal Danger of electrostatic discharge! The Shelf contains static sensitive devices. To prevent static damage you must wear an ESD wrist strap. -
Page 8: Backplane
11850-016 3 Backplane • 3.3 V management power generation on the backplane • Hot-Swap circuitry for enabling the management power and payload power by the EMCH • Fan connectors on the backplane (4-pin fan connectors) 3.1 Backplane Topology Figure 2: Backplane Topology Common Options Fabric 1/A (1000Base-BX) Port 0... -
Page 9: Fabric Interface
11850-016 3.2 Fabric Interface 3.2.1 Common Options MCH Fabric Port 1 is routed to AMC 1 Port 0. MCH Fabric Port 2 is routed to AMC 2 Port 0. MCH Fabric Port 3 is routed to AMC 1 Port 1. MCH Fabric Port 4 is routed to AMC 2 Port 1. -
Page 10: Cooling
11850-016 4 Cooling 4.1 Air Filter Figure 3: Air Filter Air Filter 4.2 Air filter swap The system provides a replaceable air filter. The air filter can be pulled out after removing the top cover. The filter meets the requirements of the Telcordia Technologies Generic Requirements GR-78- CORE specification. -
Page 11: Power Supply
11850-016 4.4 Power Supply Hazardous voltage! Parts of the power supply may be exposed with hazardous voltage. Always remove mains/line connector before carry out any assembly work. Caution! The unit is designed in accordance with protection class 1! It must therefore be operated with protec- ... -
Page 12: Emch (Embedded Microtca Carrier Hub)
11850-016 5 EMCH (Embedded MicroTCA Carrier Hub) The EMCH (Embedded MicroTCA Carrier Hub) is intended to provide basic MicroTCA functionality for switching and managing two AMC (Advanced Mezzanine Card) modules. It delivers switching and hub functionality for the system fabric gigabit ethernet (GbE) as defined in the AMC.0 standard series.... -
Page 13: Front Panel And Leds
11850-016 5.1 Front Panel and LEDs The EMCH front panel consists of two status LEDs for the AMCs, and each one LED (OK, FAIL) for the system’s operation status. In addition to the LEDs, you can find sockets for a RJ45 plug and a micro USB cable. -
Page 14: Comand Line Interface (Cli)
11850-016 5.2 Comand Line Interface (CLI) The EMCH is providing a low level command line interface (CLI) which allows to set certain operational parameters and to display run time information from the MCH and the system. 5.2.1 COM-Settings The CLI can be accessed over the front MicroUSB port. To establish a connection to a host PC, use a serial terminal program e.g. -
Page 15: Firmware Update
11850-016 5.3 Firmware Update The EMCH serves a web based front end to easily upgrade the devices firmware in field. To use this utility, first establish an ethernet link over the EMCH uplink port. If not changed, the standard interface config is as followed: Table 5: Standard interface configuration IP address: 192.168.1.138... -
Page 16: Technical Data
11850-016 6 Technical Data Table 6: Technical Data Physical Dimensions Height 43.60 mm (1 U) Width 265 mm Depth approx. 302 mm Weight Weight completely assembled approx. 2.7 Kg Power Supply Input Voltage 100 VAC to 240 VAC Mains Frequency 50 Hz to 60 Hz Input Current 1,2 A at 100 VAC;... - Page 18 Schroff GmbH Langenalber Str. 96 - 100 75334 Straubenhardt, Germany +49.7082.794.0 +49.7082.794.200 Doc-No: 63972-350_R1.0...
Need help?
Do you have a question about the SCHROFF 11850-016 and is the answer not in the manual?
Questions and answers