RHINO GPD-40 Fence Pro Owner's Manual
  1. Manuals
  2. Brands
  3. RHINO Manuals
  4. Power Tool
  5. GPD-40 Fence Pro
  6. Owner's manual

RHINO GPD-40 Fence Pro Owner's Manual

Gas powered driver
Hide thumbs
Table of Contents

Advertisement

Quick Links

Highest Quality Post Drivers and Post Pullers
GPD-40
Fence Pro
™
Gas Powered Driver
O W N E R S
M A N U A L
Form No. 301800-07/2014

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GPD-40 Fence Pro and is the answer not in the manual?

Questions and answers

Related Manuals for RHINO GPD-40 Fence Pro

Summary of Contents for RHINO GPD-40 Fence Pro

  • Page 1 Highest Quality Post Drivers and Post Pullers GPD-40 Fence Pro ™ Gas Powered Driver O W N E R S M A N U A L Form No. 301800-07/2014...
  • Page 2 Your safety, and the safety of others, is very important. The To help you make informed decisions about safety, you will find proper and safe use of your Rhino® post driver is an important important safety information in a variety of forms, including:...

  • Page 3: Table Of Contents

    Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 © 2013, 2014 Rhino Tool Company Inc., - All Rights Reserved...

  • Page 4: Introduction

    INTRODUCTION Congratulations on your selection of the operate and care for the Honda engine vice staff here at Rhino Tool Company is Rhino GPD-40 Fence Pro post driver. installed on your new post driver. standing by to assist you if you require as- ™...

  • Page 5: Driver Safety

    POST DRIVER SAFETY IMPORTANT SAFETY INFORMATION The Rhino GPD-40 Fence Pro pow- result of a post being driven into an under- The engine exhaust ™ WARNING ® ered gas operated post driver is designed ground utility. Be absolutely certain that...
  • Page 6 Bystanders should, at a minimum, wear Do not use this post • The Rhino GPD-40 Fence Pro ™ WARNING safety glasses and hearing protection while DANGER driver for any purpose...

  • Page 7: Operating Instructions

    ™ marred or destroyed, replace it immedi- of trouble free service. the above symptoms appear, seek medical ately. Simply call Rhino Tool Company advice immediately. NOTE You must read and understand your post and we will send you a new warning label...

  • Page 8: Starting The Engine

    INJURY OR DEATH driver should also be inspected for any de- To start a COLD engine, move the choke READ THIS MANUAL BEFORE fects. Do not use the GPD-40 Fence Pro ™ lever to the CLOSED position (Fig. 3). IMPORTANT...

  • Page 9: Hot Restart

    DANGER GPD-40 Fence Pro Operating Instructions... continued ™ Slide thumb switch on throttle handle Do not extend the starter rope to its full by slightly depressing the trigger and then WARNING down or into the ON position. length as it can cause damage the recoil immediately releasing it.

  • Page 10: Driving A Post

    The GPD-40 Fence Pro is equipped with OPEN position. Once you are confident that the post is the Rhino Chuck-Lok Adapter System.

  • Page 11: Maintenance

    GPD-40 Fence Pro™ Operating Instructions... continued ALWAYS HAVE THE operator can loosen the locking nut letting Never refuel your GPD-40 Fence Pro ™ WARNING LOCKING NUT IN it slide down the post, then lift the driver with the engine hot or running as there is a PLACE WHEN DRIVING POSTS: The off the post.

  • Page 12: Gpd-40 Fence Pro

    The following 2. Check all engine and post driver fasten- 2. Check crankshaft and piston lubrica- instructions are for the Rhino GPD-40 ® ers. Retighten to proper specifications if tion. See page 11 for instructions.
  • Page 13 GPD-40 Fence Pro™ Service Instructions... continued WARNING Fig. 10 - Fig. 11 - If ridge of grease measures 1/4″ After completely cleaning out old Fig. 9 - Crankcase Cover or less, add a small amount. At maximum grease, add new grease till level with the...

  • Page 14: Service Of The Hammer And Anvil

    GPD-40 Fence Pro™ Service Instructions... continued Service of the Hammer and Anvil it should appear as shown in Fig. 12. The should be replaced at this time. Clean anvil o-ring retainer (p/n 301110) will the anvil and carefully replace the anvil...
  • Page 15 GPD-40 Fence Pro™ Service Instructions... continued socket. The crank pin has LEFT-HAND ring seal (p/n 301610) should be replaced well socket. Torque to 228 inch/pounds. THREADS. Use caution holding the con- at this time. See Fig. 15. Add Rhino approved grease (p/n 300500) necting rod and crankshaft (p/n 300040).
  • Page 16 GPD-40 Fence Pro™ Service Instructions... continued into the cylinder, taking note of the small inside of the chuck tube with grease. Ap- facing toward the hammer. Insert the anvil end toward the anvil as shown in Fig. 12. ply grease to the anvil with o-ring. Insert o-ring cup into the chuck tube.
  • Page 17 GPD-40 Fence Pro™ Service Instructions... continued the anti-vibration springs into the handle tubes. Assemble the handle tubes into the upper handle cups. Insert the chuck tube into the post driver body, taking care to insert the handle tubes into the handle cups on the lower driver body.
  • Page 18 Rhino GPD-40 Fence Pro Parts List ® ™...

  • Page 19: Rhino ® Gpd-40 Fence Pro

    Rhino GPD-40 Fence Pro Parts List ® ™ Description Description 300710 Top Handle Bolts (6 Qty.) 300712 Ground Bolt 300210 Upper Handle 301015 Post Driver Body with Cylinder and Bearings 300230 Handle Cup (2 Qty.) 301075 Piston and Connecting Rod Assembly 300720 Handle Anti-Vibration Spring (4 Qty.)
  • Page 20 Rhino GPD-40 Fence Pro Parts List ® ™...
  • Page 21 300704 Crankcase Bolts (6 per driver) 300500 Rhino Post Driver Grease ® 300040 Crankshaft 301505 Service Kit for GPD-40 Fence Pro ™ 300420 Retaining Ring for Crankshaft & Clutch Drum with Pinion Gear (4 301910 GPD-40 to Fence Pro Chuck-Lok Conversion Kit ™...

  • Page 22: Limited Warranty And Registration

    Honda GX35 engine for which PROFIT OR OTHER INDIRECT, INCIDENTAL, SPECIAL OR Rhino provides no warranty and for which the warranty provided CONSEQUENTIAL DAMAGES OR LOSS ARISING OUT OF ANY by American Honda Motor Co., Inc. shall be the sole warranty ap- DEFECTS IN OR PERFORMANCE OF THE GASOLINE POW- plicable thereto.

  • Page 23: Troubleshooting

    This will position the driver on an angle with the top handle at the topmost point. Other problems or technical questions: Have your serial number handy and contact Rhino Tool Company. Phone: 309.853.5555 or Toll Free 866- 707-1808, Fax:309.856.5905, Email: info@rhinotool.com...
  • Page 24 Manufacturing Quality Post Drivers and Post Pullers Since 1977 Rhino Tool Company 620 Andrews Avenue Kewanee, IL 61443 P: 309.853.5555 or Toll Free 866-707-1808 F:309.856.5905 www.rhinotool.com E: info@rhinotool.com © 2013, 2014 Rhino Tool Company, Inc.
  • Page 25 Rhino GPD-40 Fence Pro Parts List ® ™...
  • Page 26 Rhino GPD-40 Fence Pro Parts List ® ™ Description Description 300710 Top Handle Bolts (6 Qty.) 300712 Ground Bolt 300210 Upper Handle 301015 Post Driver Body with Cylinder and Bearings 300230 Handle Cup (2 Qty.) 301075 Piston and Connecting Rod Assembly 300720 Handle Anti-Vibration Spring (4 Qty.)
  • Page 27 Rhino GPD-40 Fence Pro Parts List ® ™...
  • Page 28 300704 Crankcase Bolts (6 per driver) 300500 Rhino Post Driver Grease ® 300040 Crankshaft 301505 Service Kit for GPD-40 Fence Pro ™ 300420 Retaining Ring for Crankshaft & Clutch Drum with Pinion Gear (4 301910 GPD-40 to Fence Pro Chuck-Lok Conversion Kit ™...

Table of Contents