Advertisement

Instructions for Use of:
Model Number:
1858015
■ Do not wrap the Shock Absorbing Lanyards around any structure and connect the lanyard back onto itself, unless the lanyard has been
specifically designed to do so.
■ Striking objects horizontally due to the pendulum effect of a swing fall may cause serious injury or death.
■ Always attach an unused lanyard to a lanyard storage keeper when not in use. Never attach the unused leg of the lanyard to the
harness at any other location.
■ The regulations included herein are for reference only. They are not all-inclusive and not intended to replace a Competent Person's
judgment or knowledge of federal or state standards.
■ The analysis of the workplace must anticipate where workers will be performing tasks, the routes they will take to reach their tasks,
and the potential/existing exposure to fall hazards.
■ Fall protection equipment must be chosen by a Competent Person. Selections must account for all potential hazardous workplace
conditions.
■ All fall protection equipment should be purchased in a new and unused condition.
■ Select and install fall protection systems under the supervision of a Competent Person. Fall protection systems must be used in a
compliant manner.
■ Fall protection systems must be designed in compliance with all federal, state, and local safety regulations.
■ Forces applied to anchors must be calculated by a Competent Person.
■ Harnesses and connectors selected must be compliant with manufacturer's instructions and must be of compatible size and
configuration.
■ A pre-planned rescue procedure is required as part of a complete fall protection program. The rescue plan must be project specific.
The rescue plan must either allow for employees to rescue themselves or provide an alternative means for their prompt rescue. Store
rescue equipment in an easily accessible and clearly marked area.
■ A Competent Person must train Authorized Persons to correctly erect, disassemble, inspect, maintain, store, and use equipment.
Training must include the correct use of personal fall arrest systems, the ability to recognize fall hazards, and how to reduce the dangers
of fall hazards.
■ NEVER use any fall protection equipment to hang, lift, support, or hoist tools or equipment unless that equipment is explicitly
certified for such use.
■ Equipment must be inspected by a Competent Person at least every six months.
■ Equipment must be inspected for defects including (but not limited to): the absence of required labels or markings, improper
form/fit/function, evidence of cracks, sharp edges, deformation, corrosion, excessive heating, alteration, excessive wear, fraying,
knotting, abrasion, and absence of parts. Equipment that fails inspection in any way must immediately be removed from use or repaired
by an entity approved by the Manufacturer.
■ Physical harm may still occur even if fall safety equipment functions correctly.
■ Sustained post-fall suspension may result in serious injury or death.
This lanyard was approved by the Certification body: SATRA Technology Center, Kettering, Northants, UK.
If the product is resold outside the original country of destination the reseller shall provide instructions for use in the
language of the country in which the product is to be sold.
Y Lanyard Wind
Article Number:
1360001005
Size:
Length 1.8m
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Y Lanyard Wind and is the answer not in the manual?

Questions and answers

Summary of Contents for Hailo Y Lanyard Wind

  • Page 1 Instructions for Use of: Y Lanyard Wind Model Number: Article Number: Size: 1858015 1360001005 Length 1.8m ■ Do not wrap the Shock Absorbing Lanyards around any structure and connect the lanyard back onto itself, unless the lanyard has been specifically designed to do so.
  • Page 2: Limitations Of Use

    Limitations of Use ■ Shock Absorbing Lanyards marked “EN355-2002” require space for up to 4m of free fall with a maximum capacity up to 100 kg including clothing, tools, etc. ■ Shock Absorbing Lanyards must be used with a full body harness. ■...
  • Page 3 Snap Hooks and Carabiners Snap hooks and karabiners used on This Shock Absorbing Lanyard marked with the EN362 standard are self-closing with minimal tensile break strength of 22KN,a minimum gate rating of 1KN, and a minimum side load gate rating of 1.5KN. Basic Rules Of Using The Snap Hook: •...
  • Page 4 Fall Clearance/Clear Fall Charts Clearance Requirements These illustrations are an example of how to calculate fall clearance when using a self-retracting lanyard or a shock-absorbing lanyard. Image 1 shows a self-retracting lanyard anchored overhead with the other end connected to the dorsal D-ring of a full body harness. When positioning a self-retracting lanyard, include the following distances in your calculations: Using the Self-Retracting Lanyard will require a total fall clearance of approximately 2.0 m as measured from the working level to the nearest obstruction below.
  • Page 5: Operation

    Swing fall To minimize the possibility of a swing fall, work as directly under the anchorage connector as possible. Striking objects horizontally, due to the pendulum effect, may cause serious injury. Swing falls also increase the vertical fall distance of a worker, compared to a fall directly below the anchorage connector.
  • Page 6 Connecting Shock Absorbing Lanyards That Have a Shock-Pack Absorbing Lanyards with a shock-pack must be connected in a specific location. The shock absorbing end of the lanyard must connect to the dorsal D-ring of the full body harness. The opposite end of the lanyard is to be connected to the anchorage connector. Connecting Y-Lanyards Y-Lanyards are designed for single person use only.
  • Page 7: Cleaning, Maintenance And Storage

    Training Employers are responsible for providing training to any employee who may be exposed to fall hazards. Training will enable an employee to recognize and reduce fall hazards. Training must be conducted by a Competent or Qualified Person. Trainer and trainees must not be exposed to fall hazards during the training course.
  • Page 8 Maintenance Any Shock Absorbing Lanyards requiring maintenance must be tagged “unusable” and removed from service. Storage When not in use, Shock Absorbing Lanyards should be stored in a cool, dry place out of direct sunlight. ■ Do not store in areas where damage from environmental factors such as heat, light, excessive moisture, oil, chemicals and their ■...
  • Page 9: Inspection Record

    Notified Body involved with design stage & involved in the production control phrase: SATRA Technology Europe Ltd Bracetown Business Park,Clonee,Dublin D15 YN2P,Ireland Seller: Ningbo Hailo Wind Systems Co., Ltd No.12 Pushun Road Beilun District, Ningbo, China, PC:315803 Fax: +86 (0)574 8687 6603 Tel: +86(0)574 8687 6675...

This manual is also suitable for:

1858015

Table of Contents