Advertisement
Quick Links
Congratulations on your purchase of one of the premier tow boat products in the industry! This
bimini top is designed to provide you years of service and satisfaction with the proper care and instal-
lation. Please read these instructions carefully. If at any time you have a question about the bimini
or installation, please call (480) 609-1182 and ask for technical assistance.
•
This Bimini is designed to used at tow boat speeds only. Do not trailer boat while deployed.
•
Do not allow passengers to hang on or pull on rear frame extension wihile deployed.
•
Ensure all bolts and hardware are tightened before each use.
•
Do not use bimini if hardware is missing or broken or if the bimini shows any type of stress (cracks, broken welds, etc).
•
When operating or towing boat with bimini installed, be aware of low bridges, waterways, powerlines, trees, or other low objects
that may come into contact with bimini top.
•
Do not store surf boards or other objects on top of bimini.
•
Failure to adhere to these safety warnings and guidelines will void warranty and may cause personal injury.
Axis Rear Bimini
2015-2019 (all models)
Instruction Manual
*****Important Safety Precautions*****
Please Read
Fluid Concepts
134 E. Broadway Rd. #101
Mesa, AZ 85210
(480) 609-1182
info@fluidconcepts.net
www.fluidconcepts.net
Advertisement
Summary of Contents for Fluid Concepts Rear Bimini
- Page 1 Mesa, AZ 85210 (480) 609-1182 info@fluidconcepts.net www.fluidconcepts.net Axis Rear Bimini 2015-2019 (all models) Instruction Manual Congratulations on your purchase of one of the premier tow boat products in the industry! This bimini top is designed to provide you years of service and satisfaction with the proper care and instal- lation.
-
Page 2: Unpack Contents
Please identify parts using the list below. Now is a good time to inspect parts for damage from shipping. Rear Frame Folding Arm Assembly Stanchions Front Frame Assembly Front Shorts w/Snaps Canvas and Boot Hinges Ball End Fittings Fig 1 Fig 2 Fluid Concepts Page 2... - Page 3 Fig-5A At this point you should have two separate frames assembled (front frame and rear frame) as shown in Fig 3 Fig-5B. Snap Button Snap Button fully engaged Fig 4A Fig 4B Set Screw Rear Frame Front Frame Fig 5A Fig 5B Fluid Concepts Page 3...
- Page 4 Fig-8 NOTE: The quick-release fittings are mirrored parts. There is a left and right. There is also a top and bottom. The larger opening (and D-Ring Twist Pin) are located toward the top of Fig 4 Fig 8 the fitting. This allows the bimini ball end to slide downward to lock into place. Fluid Concepts Page 4...
- Page 5 Notice pin on back of mounting bracket sits in corner of machined window of tower. Fig-12 Once everything is in place, tighten all screws using 1/4” hex key/wrench. Fig 12 Fluid Concepts Page 5...
- Page 6 Do the same for the opposite side. Lock in place by turning D-Ring Twist Pin until groove is closed. Fig-16 The rear bimini frame should look Fig 15 like this. Fig-17 D-Ring Groove-...
- Page 7 Fig-21 Step 5: Again, using rear zipper pocket, secure canvas around rear frame and zip. See instructions below to setup Fig 20 bimini for use. Fig-22 Fig 21 Fig 22 Fluid Concepts Page 7...
- Page 8 NOTE: While towing boat when bimini is in the stow position, it is a good idea to push dangling hinge pins into hole. Be sure to remember to remove them before deploying bimini! Fig 25 White Nylon Frame Clips Fig 26 Fig 27 Fluid Concepts Page 8...
- Page 9 Reverse Process to Stow. Do not hang from bimini frame. This will cause premature wear and may damage canvas or frame. Fig 30 Fig 31 Fig 32 Fluid Concepts Page 9...
-
Page 10: Care And Maintenance
Defective merchandise must be returned to your local authorized Fluid Dealer for warranty issues. To locate an Authorized Dealer please email or call Fluid Concepts direct. If the return of defective merchandise is necessary, call Fluid at (800) 284-6615 to obtain a Return Authorization (RA) number.