Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Efitment RW025
Summary of Contents for Efitment RW025
- Page 1 RW025 Magnetic Rowing Machine with Steel Slide Rail User Manual IMPORTANT: Read all instructions carefully before using this product. Retain owner’s manual for future reference. For customer service, please contact: service@zoovaa.com...
-
Page 2: Important Safety Information
IMPORTANT SAFETY INFORMATION We thank you for choosing our product. To ensure your safety and health, please use this equipment correctly. It is important to read this entire manual before assembling and using the equipment. Safe and effective use can only be assured if the equipment is assembled, maintained, and used properly. -
Page 3: Exploded Drawing
EXPLODED DRAWING - 2 -... -
Page 4: Parts List
PARTS LIST DESCRIPTIONS DESCRIPTIONS 號 號 Coil spring flywheel 32 Bushing Adjustable magnetic control 33 Rubber foot pad Fixable magnetic control 34 Sensor wire Seat 35 Velcro Meter 36 Tension control knob Main frame 37 Pulley Sliding rail 38 Pedal strap Rear stabilizer 39 Foam grip Front stabilizer... -
Page 5: Hardware Package
HARDWARE PACKAGE - 4 -... - Page 6 ASSEMBLY INSTRUCTIONS STEP 1. Attach the Front Stabilizer (No.9) into the Main Frame (No.6) using 2 Screws (No.42), 2 Arc Washers (No.59), 2 Spring Washers (No.58) and 2 Cap Nuts (No.47). Tighten with Spanner (No.61). - 5 -...
- Page 7 ASSEMBLY INSTRUCTIONS STEP 2. Insert the Pedal Shaft Core (No.14) into pedal support post the Main Frame (No.6). Slide the Pedals (No.18) onto each end of the Pedal Shaft Core (No.14). Secure using 2 Flat Washers (No.56) and 2 Allen Screws (No.48). Tighten with Allen Wrench (No.62). - 6 -...
- Page 8 ASSEMBLY INSTRUCTIONS STEP 3. Insert the Saddle (No.4) onto the Sliding Rail (No.7) following the direction of arrow. Fix Limit Pad (No.17) and Screw (No.11) into the Sliding Rail (No.7). 4PCS STEP 4: Attach the Rear Stabilizer (No.8) to the Sliding Rail (No.7) using 4 Flat Washers (No.56), 4 Spring Washers (No.58) and 4 Allen Screws (No.49).
- Page 9 ASSEMBLY INSTRUCTIONS STEP 5. Connect the Computer Trunk Wire (No.60) with the Sensor Wire (No. 34). Attach the Sliding Rail (No.7) to Main frame (No.6) using 2 Connecting Axles (No.13), 4 Flat Washers (No.40), Spring Washers (No. 58) and 4 Cap Nuts (No.47). - 8 -...
-
Page 10: Adjustment Guide
ADJUSTMENT GUIDE PEDAL ADJUSTMENT The pedal strap is adjustable and can be personalized to fit the user’s foot size. To adjust the pedal strap, remove the Velcro end of the strap from the mesh side by pulling it upward then to the left. Once removed, you may increase the opening of the pedal strap by pulling the mesh end up and to the right. -
Page 11: Adjusting The Resistance
ADJUSTMENT GUIDE ADJUSTING THE RESISTANCE Rotate the Tension Control Knob (No.36) clockwise to increase the level of resistance. Rotate the Tension Control Knob (No.36) counter-clockwise to decrease the level of resistance. Tension levels are set at Level 1 being the lowest and Level 8 being the highest. CAUTION! Moving parts, such as the seat, can crush and cut. -
Page 12: Meter Instructions
METER INSTRUCTIONS CNT (COUNT) --------------------------------------------------------------------------------0~9999 TIME (TIME)-------------------------------------------------------------------------0:00~99:59MIN RPM ( STROKES/MINUTE) ---------------------------------------------------------------0~9999 CAL (CALORIES)--------------------------------------------------- 0~9999 (0.0~999.9) KCAL DIST (DISTANCE) --------------------------------------------------------------------0.1-999.9 ML KEY FUNCTIONS MODE: Press to select functions: time, calories, rpm, scan, count. Hold the button for 3 seconds to reset all values. OPERATION PROCEDURES AUTO ON/OFF When you start rowing or press the MODE key, the meter will turn on.
Need help?
Do you have a question about the RW025 and is the answer not in the manual?
Questions and answers