Related Manuals for LOGICDATA DMUI-EASY2move
Summary of Contents for LOGICDATA DMUI-EASY2move
- Page 1 DOCUMENT VERSION 1 | AUGUST 2019 DYNAMIC MOTION system DMUI- EASY2move User Manual DYNAMIC MOTION...
- Page 2 DMUI-EASY2MOVE - OPERATING MANUAL // PAGE 2 DMUI-EASY2move - Operating Manual Document Version 1.0 / August 2019 This document was originally published in English. LOGICDATA Electronic & Software Entwicklungs GmbH Wirtschaftspark 18 8530 Deutschlandsberg Austria Phone: +43 (0) 3462 51 98 0...
-
Page 3: Table Of Contents
DMUI-EASY2MOVE - OPERATING MANUAL // PAGE 3 CONTENTS General information Other applicable documents Copyright Royalty-free use of images and text Trademarks Safety Target audience General safety regulations Intended use Reasonably foreseeable misuse Explanation of symbols and signal words Liability Residual risks... - Page 4 DMUI-EASY2MOVE - OPERATING MANUAL // PAGE 4 7.2.1 Saving a Container Stop or Shelf Stop Position 7.2.2 Deleting a Container Stop or Shelf Stop Position Performing a Position Reset Procedure Factory Reset (S0 Reset) System Information Additional Information Software-Dependent Functions...
-
Page 5: General Information
No part of the text and no image may be used without the prior written consent of LOGICDATA. Texts and images may not be sold in their current state, and may not be published or sublicensed digitally. -
Page 6: Safety
2.3 INTENDED USE The DMUI-EASY2move is a Paddle Switch Handset for electrically Height-Adjustable Tables. It is installed by Resellers into Height-Adjustable Table systems. It is used to control Height-Adjustable Table systems via the DYNAMIC MOTION system. -
Page 7: Explanation Of Symbols And Signal Words
2.6 LIABILITY LOGICDATA products comply with all relevant industry standards, which are listed in the product's data- sheet. However, risk can result from incorrect operation or misuse. LOGICDATA is in particular not liable for damage or injury caused by: • Improper product use •... -
Page 8: Residual Risks
Residual risks associated with the installation of the DMUI-EASY2move Handset are listed here and throughout this Operating Manual. See also Chapter 1.1 Other Applicable Documents on page 5. The symbols and signal words used in this Operating Manual are listed in Chapter 2.5 Explanation of Symbols and Signal Words on page 7. -
Page 9: Skilled Persons
• Ensure that persons with limited ability to react to danger do not take part in the assembly process DMUI-EASY2move Handsets may only be installed by Skilled Persons. A Skilled Person is defined as some- one who: • Is authorized for installation planning, installation, commissioning, or servicing of the product •... -
Page 10: Unpackaging
5 PRODUCT The illustrations in this chapter show a standard model of the DMUI-EASY2move Handset. The exact variant of the DMUI-EASY2move is denoted by the product's order code. Consult the accompanying data sheet to ensure that you have received the correct variant. -
Page 11: Dimensions
DMUI-EASY2MOVE - OPERATING MANUAL // PAGE 11 5.2 DIMENSIONS Length 121.82 mm | 4.796 " Width 47.22 mm | 1.859" Height (Contact Point to Mounting Point) 25.85 mm | 1.136 " 121,82 mm 4.796 " 47,22 mm 1.859 " Fig. 2:... -
Page 12: Drilling Template
The Drilling Template below is a recommended Mounting Position. Resellers are allowed to choose any suit- able position for the DMUI-EASY2move. In the recommended Mounting Position, the DMUI-EASY2move is positioned so that the distance from the front edge of the table to the centre of the first Mounting Point is 40 mm. -
Page 13: Assembly
Tightening torque depends on the material of the Table Top. Do not exceed 2 Nm. 6.4 COMPLETING ASSEMBLY After the DMUI-EASY2move is attached to the Table Top, you must connect the Cable to the DYNAMIC MOTION syste. Refer to the DYNAMIC MOTION system manual for instructions. -
Page 14: Operation
INFO stopping point has been reached. INFO The LEDs on the DMUI-EASY2move will light up white when the table is in motion. 7.1.1 MOVING THE TABLE TOP UP Gently lift and hold the paddle until the desired height has been reached (Fig. 4). -
Page 15: Moving The Table Top Down
DMUI-EASY2MOVE - OPERATING MANUAL // PAGE 15 7.1.2 MOVING THE TABLE TOP DOWN Gently push and hold down the paddle until the desired height has been reached (Fig. 5). Fig. 5: Moving the Table Top Down 7.2 CONTAINER STOP AND SHELF STOP POSITIONS These features can limit the movement area of the Table Top (if e.g. -
Page 16: Factory Reset (S0 Reset)
DMUI-EASY2MOVE - OPERATING MANUAL // PAGE 16 1. Gently push and hold down the paddle until the table stops at the lower position limit 2. Release the Paddle 3. Push and hold down the Paddle again ▸ The table will move down slightly, then up again 4. -
Page 17: System Information
DMUI-EASY2MOVE - OPERATING MANUAL // PAGE 17 8 SYSTEM INFORMATION When a DMUI-EASY2move Handset is installed alongside the DYNAMIC MOTION system, system informa- tion is communicated via flashes of the LED Signal Light. Possible signals are as follows: Signal Message... -
Page 18: Additional Information
SOFTWARE-DEPENDENT FUNCTIONS A full list of Software-Dependent Functions can be found in the DYNAMIC MOTION system manual. 9.2 DISASSEMBLY To disassemble the DMUI-EASY2move, disconnect the DYNAMIC MOTION system from the mains. Then, follow the assembly instructions in reverse order. 9.3 MAINTENANCE The DMUI-EASY2move Handset is maintenance-free. - Page 19 LOGICDATA LOGICDATA North America, Inc. Electronic & Software Entwicklungs GmbH Broadmoor Ave SE, Suite D Wirtschaftspark 18 Grand Rapids MI 8530 Deutschlandsberg Austria Phone: +1 (616) 328 8841 Phone: +43 (0)3462 5198 0 Email: office.na@logicdata.net Fax: +43 (0)3462 5198 1030 Email: office.at@logicdata.net...