1. Manuals
  2. Brands
  3. adstec Manuals
  4. Desktop
  5. TabX ITC8113
  6. Instruction manual

adstec TabX ITC8113 Instruction Manual

Tablet pcs
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Version
2.1
Translation of the original
instruction manual
Updated 2019-08-13
Instruction manual
Tablet PCs
ITC8113 / TabX®

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TabX ITC8113 and is the answer not in the manual?

Questions and answers

Summary of Contents for adstec TabX ITC8113

  • Page 1 Version Translation of the original instruction manual Instruction manual Tablet PCs ITC8113 / TabX® Updated 2019-08-13...

  • Page 2: Table Of Contents

    ITC8113 / TabX® Table of Contents Notes ............................5 General remark Limitation of liability Manufacturer Relevant device documentation Safety instructions ........................7 Structure of safety instructions Graduation of risk level Explanation of used symbols Symbols Data, figures and modifications Trademarks Copyright Environmental conditions Standards...
  • Page 3 ITC8113 / TabX® Interfaces ..........................28 Interfaces on the side 6.1.1 Standard version 6.1.2 Versions with DisplayPort Power supply via the power adapter Power supply via stick-type batteries USB interfaces Network connection (RJ45) Microphone Speakers Wireless ..........................37 WLAN Bluetooth UMTS / LTE (optional) Drives ............................
  • Page 4 ITC8113 / TabX® 12 Component replacement ......................64 12.1 Opening the service slot 12.2 Changing the mass storage device 12.3 Replacing the BIOS battery 13 Service & support ........................68 13.1 ADS-TEC support 13.2 Company address © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany...

  • Page 5: Notes

    ITC8113 / TabX® 1 Notes 1.1 General remark This instruction manual is intended to ensure safe and efficient handling and operation of IT Infrastructure products. The instruction manuals must be read carefully by personnel before commencing any type of work. All of the safety notices and handling instructions given in the manual must be obeyed in order to ensure that work is carried out safely.

  • Page 6: Manufacturer

    ITC8113 / TabX® 1.3 Manufacturer The manufacturer of the product is ads-tec Industrial IT GmbH. The company is referred to in the following as ADS-TEC. 1.4 Relevant device documentation The following documents are decisive to device setup and operation: Instruction manual: Contains information for installation, commissioning and operation of the device along with technical data of the device hardware.

  • Page 7: Safety Instructions

    ITC8113 / TabX® 2 Safety instructions 2.1 Structure of safety instructions The signal word classifies the hazard. Reference to the type/consequences and source of the hazard is made underneath the signal word. Instructions for preventing the hazard are identified by an arrow (). SIGNAL WORD Type/consequences of hazard! - Source of hazard...

  • Page 8: Symbols

    ITC8113 / TabX® ATTENTION Indicates a possibly damaging situation. If not avoided, the system or something in its surroundings could be damaged. Recommendation for use: The symbol "Recommendation for use" indicates terms and/or conditions that strictly need to be observed to ensure optimised and/or zero-defect operation.

  • Page 9: Copyright

    ITC8113 / TabX® 2.7 Copyright This instruction manual is protected by copyright. For the authorised user, simple usage rights are granted within the scope of the intent of the contract. Any modified use or exploitation of the provided content, particularly duplication, modification or publishing in whatever form is permitted only with the prior consent of ADS-TEC.

  • Page 10: Standards

    ITC8113 / TabX® 2.9 Standards The manufacturer hereby declares that this device has been marked with the CE mark in accordance with the basic requirements and other relevant conditions of the following European Directives: 2011/65/EU, RoHs Directive • 2014/30/EU, EMC Directive •...

  • Page 11: Scope Of Delivery

    ITC8113 / TabX® 2.10 Scope of delivery Check the contents of the package for completeness and for any damages: Should the device have evident signs of damages caused, e.g., by improper operation or storage conditions or due to improper use or handling, the device and accessories must be shut down immediately.

  • Page 12: Features Of The Itc8113

    ITC8113 / TabX® 2.11 Features of the ITC8113 The industrial tablet computer from ADS-TEC has been consistently further developed for professional and mobile use. High performance, brilliant Full HD display and optimised for applications in service environments – the new TabX - ITC8113 scores high marks both for indoor and outdoor use.
  • Page 13 ITC8113 / TabX® Rear side Description Battery ejector Set-up mechanism Service slot Docking connector © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany...

  • Page 14: External Dimensions Itc8113

    ITC8113 / TabX® 2.12 External dimensions ITC8113 © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany...

  • Page 15: Operating And Safety Instructions

    ITC8113 / TabX® 3 Operating and safety instructions The device operates under electrical voltage and contains highly sensitive components. Intervention by the user is required only for connecting the power supply lines. Should any further modifications be required, it is necessary to consult either with the manufacturer directly or with service personnel authorised by the manufacturer.

  • Page 16: Operating Location

    ITC8113 / TabX® 3.1 Operating location The device is optimised for use with applications in a service environment. Make certain that the specified environmental conditions are maintained at all times. Use in non-specified environments, i.e., on board ships, in explosive atmospheres or at extreme elevations, is prohibited.

  • Page 17: Improper Use

    ITC8113 / TabX® 3.5 Improper use Operation other than or beyond that described for the device shall be deemed improper use. The device is not allowed to be used to control vehicles or for applications for which further approvals beyond the manufacturer's declaration are necessary, e.g. applications with explosion hazard, medical technology, shipping industry.

  • Page 18: Electrostatically Sensitive Components

    ITC8113 / TabX® 3.7 Electrostatically sensitive components ATTENTION Damage due to electrostatic discharges  All installation and service work performed on the device must be performed only under safe, secure and de-energised conditions. Always adhere to the safety measures applicable when handling components at risk of being damaged by electrostatic discharges.

  • Page 19: Commissioning

    ITC8113 / TabX® 4 Commissioning The power supply connection and the interfaces on the device are located on the side of the housing. All supply leads and all required data leads have to be connected before commissioning. ATTENTION The device must be switched off before connecting or disconnecting any cables in order to prevent damage to the electronics! The device may only be switched on after acclimatising to the ambient temperature in order to avoid condensate accumulation.

  • Page 20: Operation

    ITC8113 / TabX® 5 Operation 5.1 Full HD display The device is equipped with a full-HD display with multifunction touch-screen. The non-reflective display offers a maximum resolution of 1920 x 1080 pixels. © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany...

  • Page 21: 10-Finger Multifunction Touch-Screen

    ITC8113 / TabX® 5.2 10-finger multifunction touch-screen The device is equipped with a multifunction touch-screen that supports multifinger operation. The driver software necessary for use is already integrated in the respective operating system. Recommendation for use: The touch calibration data is stored independent of the operating system and requires no additional calibration by the user.

  • Page 22: Front Status Leds

    ITC8113 / TabX® 5.3 Front status LEDs The device is equipped with various status LEDs on the front. These LEDs indicate current events such as system activity, battery state, and WLAN and Bluetooth activity. System LED Behaviour Description Device is not connected to any voltage source (power supply/battery) Static...
  • Page 23 ITC8113 / TabX® Static Device is operating with the remaining capacity of the battery(ies) WLAN LED Static WLAN module is not switched on Static WLAN module is switched on Flashing Device is connected to a WLAN network and has data traffic Bluetooth Static Bluetooth module is deactivated.

  • Page 24: Front Panel Operation Keys

    ITC8113 / TabX® 5.4 Front panel operation keys Recommendation for use: After activating the operating system, the soft keyboard can be opened using the corresponding front key. If the soft keyboard is not installed, it can be added. Details can be found in the instruction manual for the Configuration Center. ©...
  • Page 25 ITC8113 / TabX® The keys on the front are assigned the following functions by a special driver in the soft keyboard: Hold down the ON/OFF pushbutton for 0.5 sec. Shift key (SHIFT) for activating the second keyboard level. This key must be pressed simultaneously with the desired function key.
  • Page 26 ITC8113 / TabX® Recommendation for use: With the exception of the ON/OFF pushbutton and the Fn key, each of the function keys on the front has two function levels. The primary function can be executed by simply pressing the respective key. The second function level of each key (small icon in the upper right) can be executed by first pressing the Fn key followed by the desired function key.

  • Page 27: Landscape/Portrait Function

    ITC8113 / TabX® 5.5 Landscape/portrait function Press Landscape/portrait rotate from 0° 90°. Press the key again to return to the initial state. The function ensures that the preset calibration for 0° or 90° is always loaded. ATTENTION Keep the air outlet at the right near the card slots free of obstruction. To protect the device from overheating, make certain that the air outlet slots are not covered or that the air outlet is not impeded.

  • Page 28: Interfaces

    ITC8113 / TabX® 6 Interfaces All available interfaces are located on the side of the device. They are protected by a rubber cover. ATTENTION Breaching of IP protection IP protection is no longer provided if the rubber covers are open. ...

  • Page 29: Versions With Displayport

    ITC8113 / TabX® 6.1.2 Versions with DisplayPort Pos : 26 /D atentec hni k/Schnitts tell en/Spannungs versorgung/Spannungs versorg ung für VMT60xx- Seri e @ 2\mod_1260450284020_6.doc @ 6853 @ Description DisplayPort (Video OUT) USB interfaces LAN interface Power supply Depending on the version of the device: BNC connector (analogue video IN) –...

  • Page 30: Power Supply Via The Power Adapter

    ITC8113 / TabX® 6.2 Power supply via the power adapter Technical data of the power adapter • Power consumption: 70 watts • Input voltage: 100…240 VAC • Output voltage: 20 VDC • Grid frequency: 47…63 Hz • Current consumption: 3.5A (230 VAC) ©...

  • Page 31: Power Supply Via Stick-Type Batteries

    ITC8113 / TabX® 6.3 Power supply via stick-type batteries The device is equipped with two battery slots that can be used as an alternative for supplying the device with power. In addition, the device is equipped with the hot-swap function, which allows batteries to be changed without restarting. The batteries are automatically charged during mains operation (20 VDC).
  • Page 32 ITC8113 / TabX® Querying the battery state / changing the battery The device batteries can be removed using a mechanical ejector located on the rear side of the device. To do this, press the respective key. The charge state can be queried via the "Test Power" button on the battery. The charge state indicator illuminates for a few seconds and displays the current charge state on a scale from 0 to 100.

  • Page 33: Usb Interfaces

    ITC8113 / TabX® 6.4 USB interfaces The USB interfaces are used for connecting peripherals with USB connection. These interfaces comply with the USB 3.0 standard requirements. USB 3.0 Signal VBUS StdA_SSRX− StdA_SSRX+ GND_DRAIN StdA_SSTX− StdA_SSTX+ Recommendation for use: The recessed USB interface (not available in the Display port version) enables the use of a USB dongle.

  • Page 34: Network Connection (Rj45)

    ITC8113 / TabX® 6.5 Network connection (RJ45) If the drivers required for functioning are installed on the device, the device may be integrated in an Ethernet network supporting the 10/100/1000Mbit standard by using the Ethernet 10/100/1000 BaseT network connector. The specifications of this network topology must be observed. If the drivers necessary for the function are not installed, they can be downloaded from the website www.ads-tec.de.

  • Page 35: Microphone

    ITC8113 / TabX® 6.6 Microphone The device is also equipped with an internal microphone on the front side. The microphone can be configured via the integrated volume control in the operating system. © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany...

  • Page 36: Speakers

    ITC8113 / TabX® 6.7 Speakers The device is equipped with two internal speakers. Speaker positions The volume can be set up by using the device front keys. When activating the described key combinations, the volume level is modified accordingly. If the soft keyboard has been installed, the system volume is additionally displayed by a bar graph.

  • Page 37: Wireless

    ITC8113 / TabX® 7 Wireless The device features various wireless options for establishing a connection to networks or compatible terminals. Recommendation for use: The appropriate drivers can be downloaded from the website http://www.ads-tec.de for the respective device series. 7.1 WLAN The device is equipped with a wireless LAN card and can be integrated wirelessly in any IT infrastructure.

  • Page 38: Bluetooth

    ITC8113 / TabX® 7.2 Bluetooth The device is equipped with a Bluetooth module. Recommendation for use: The wireless module supports the Bluetooth 4.0 standard. The built-in wireless module meets the CLASS 1 / CLASS 2 standard. 7.3 UMTS / LTE (optional) The device is equipped with a mobile communications module and is able to communicate with the Internet even without a wireless infrastructure.

  • Page 39: Drives

    ITC8113 / TabX® 8 Drives 8.1 Hard disk / Flash SSD The storage medium is selected according to the customer requirements. The following options are available for storage: ̶ Solid-state drive (SSD) ̶ An HDD is optionally available. ̶ The capacity is dependent on the desired operating system and the used programs. Pos : 35 /D atentec hni k/Laufwer ke/Exter ne Laufwerke/Exter ne Laufwer ke für OPC 5112 / 5115 / 5117 / IPC 1100 / CPC / PLC / OTC / ITC / VMT-Serie @ 0\mod_1158926656205_6.doc @ 563 @ 8.2 External drives External storage media can be connected via USB interfaces.

  • Page 40: Software

    ITC8113 / TabX® 9 Software 9.1 Reinstalling the operating system The device will be delivered with a pre-installed operating system depending on what the customer wants. The drivers required for this, are already installed and the operating system will be enabled by entering the licence information. Recommendation for use: The device does not have an integrated CD drive.

  • Page 41: Technical Details

    ITC8113 / TabX® 10 Technical details 10.1 Technical details of the ITC8113 ITC8113 Housing Glass-fibre reinforced monocoque frame Display Resolution 13.3" TFT, Full HD, LED backlight 1920 x 1080 pixels Touch PCAP multifunction industrial touch screen (10-finger) Processor Intel® Intel® Celeron™ 1.6 GHz (2980U) Intel®...

  • Page 42: Technical Details Of The Stick-Type Batteries

    ITC8113 / TabX® 10.2 Technical details of the stick-type batteries Stick-type battery type DZ-PCKO-06097-8/x Nominal voltage 14.6 V Minimum capacity 2750 mAh Nominal energy 40 Wh Cell Samsung INR18650-29E Number of cells ADS-TEC article no. DZ-PCKO-06097-8/x Admissible operating temperature range •...

  • Page 43: Accessories

    ITC8113 / TabX® 11 Accessories 11.1 Transport case The optionally available transport case allows the device to be transported safely. In addition, the transport case offers the possibility to store accessory parts such as batteries, power adapters and software. Exterior view of sample case Please note: The transport case is not a UL-certified accessory.

  • Page 44: Battery Charging Station

    ITC8113 / TabX® 11.2 Battery charging station A battery charging station is optionally available for charging the device batteries (Article no.: DV-ITCOPT-002 001-AA). The battery charging station has two battery slots. Two batteries can thereby be charged simultaneously. Please note: The battery charging station is not a UL-certified accessory. ©...
  • Page 45 ITC8113 / TabX® 20 VDC ONNECTING THE POWER ADAPTER Before starting up the battery charging station, a 20 VDC power adapter must be connected. Connect the power adapter on the rear side of the battery charging station. The power adapter for the device can be used to supply power to the battery charging station (20 VDC).
  • Page 46 ITC8113 / TabX® NSERTING THE BATTERIES Insert the batteries into the battery slots so that there is a connection between the charging contacts of the battery charging station and the batteries. Recommendation for use: If the battery was correctly inserted in the battery charging station, an audible signal sounds and the charging process begins.
  • Page 47 ITC8113 / TabX® STATUS INDICATORS Various system activities are indicated during operation. EADY INDICATOR EHAVIOUR ESCRIPTION No battery inserted Static Battery fully charged Static Battery is faulty HARGE INDICATOR Battery is not charging Flashin Battery is charging SYS LED INDICATOR Device is not connected to any voltage source (power supply/battery)
  • Page 48 ITC8113 / TabX® ICTOGRAPHIC REPRESENTATION Battery is charging Battery fully charged Device is not ready for operation / defective power source Battery is faulty © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany...

  • Page 49: Replacement Power Adapter

    ITC8113 / TabX® 11.3 Replacement power adapter A replacement power adapter is optionally available for operating the device (Article no.: DV-ITCOPT-004 001-AA). Please note: This is a UL-certified accessory. 11.4 Vehicle power adapter A vehicle power adapter is optionally available for operating the device (Article no.: DV- ITCOPT-005 001-AA).

  • Page 50: Replacement Stick-Type Battery

    ITC8113 / TabX® 11.5 Replacement stick-type battery A replacement battery is optionally available for operating the device (Article no.: DV-ITCOPT-003 001-AA). Please note: This is a UL-certified accessory. © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany...

  • Page 51: Rotatable And Tiltable Wall Table Adapter

    ITC8113 / TabX® 11.6 Rotatable and tiltable wall table adapter In combination with the table stand / wall bracket, the available docking station offers a stable mounting solution for every installation site. The device can be connected to the docking station using the docking connector on the rear side of the device.
  • Page 52 ITC8113 / TabX® Fastening the docking station to the stand / wall bracket Tighten the screws contained in the scope of delivery as shown in the picture. Screws: M5x25, DIN 7991, strength 8.8, Allen key 3 mm, torque 1 Nm. Fastening the bracket to a table or a wall Use adequate screws and plugs depending on the load-bearing capacity of the supporting surface of the table or wall for safe mounting.
  • Page 53 ITC8113 / TabX® OUNTING THE DEVICE TO THE DOCKING STATION 1) Place device on red marking behind the turquoise marking 2) Push device to the back onto the docking station. You should feel the device click into place © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany...
  • Page 54 ITC8113 / TabX® EMOVING THE DEVICE FROM THE DOCKING STATION 1) Push the turquoise release downward and hold down 2) Tilt the device forward slightly 3) Lift the device upward to disconnect and remove it from the docking station The docking solution shown here illustrates the mechanical release. A lockable docking solution is also available.

  • Page 55: Tip-Up Feet

    ITC8113 / TabX® 11.7 Tip-up feet The tip-up feet enable comfortable operation anywhere. © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany...

  • Page 56: 3-Point Strap

    ITC8113 / TabX® 11.8 3-point strap A 3-point strap is optionally available for mobile use. The 3-point strap can be mounted directly to the device and makes the device a mobile workplace. Please note: The 3-point-strap is not a UL-certified accessory. 1 x DZ-MECH-33255-1 (A) M5x16 flat-head screw, galvanised DIN 921 2 x DZ-MECH-33255-2 flat head screw.
  • Page 57 ITC8113 / TabX® OUNTING THE POINT STRAP TO THE DEVICE 1) First attach the strap eyelets to the device. In doing so, the appropriate mounting option must be selected for left- or right-handed users. Left-handed users: white marking Right-handed users: red marking ©...
  • Page 58 ITC8113 / TabX® 2) Screw down the strap eyelets at the marked positions as shown in the figure. Recommendation for use: Tighten the screws to max. 120 Ncm. The strap eyelets should still move without loosening the screw. Mounted state for right-handed users ©...
  • Page 59 ITC8113 / TabX® 3) The shoulder strap can be attached to the strap eyelets via the carabiners. The device is ready for mobile use. Recommendation for use: The tilt adjustment of the shoulder strap (upper right) should always be attached to the upper side of the device. ©...
  • Page 60 ITC8113 / TabX® © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany...

  • Page 61: Hand Strap

    ITC8113 / TabX® 11.9 Hand strap As an alternative to the shoulder strap, a hand strap is available for mobile use. The hand strap can be mounted directly on the device and turns the device into a mobile workplace. Please note: This is a UL-certified accessory. 2 x supplied screws 1 x hand strap OUNTING THE HAND STRAP ON THE DEVICE...
  • Page 62 ITC8113 / TabX® 2) Screw down the hand strap at the marked positions as shown in the figure. Recommendation for use: Tighten the screws to max. 120 Ncm. 2) Mounted hand strap © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany...

  • Page 63: Protection Cover

    ITC8113 / TabX® 11.10 Protection cover The optionally available protection cover offers protection against transport damages. Please note: The 3-point-strap is not a UL-certified accessory. © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany...
  • Page 64 ITC8113 / TabX® 12 Component replacement ATTENTION Make certain that all cables are disconnected and that no voltage is connected to the device! 12.1 Opening the service slot Remove the six screws for the service slot on the rear of the device. The screws can be removed with a size Tx 8 screwdriver.
  • Page 65 ITC8113 / TabX® By removing the service slot cover, it is possible to replace the following components. HDD / SSD Lithium battery © ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany...
  • Page 66 ITC8113 / TabX® 12.2 Changing the mass storage device Removal The extraction aid on the mass storage device should be used for removing. Pull out the storage medium. Installation The mass storage device must be carefully inserted into the slot and should noticeably engage.
  • Page 67 ITC8113 / TabX® 12.3 Replacing the BIOS battery The BIOS battery may only be replaced with a battery of the same type. The battery type to be used is: Lithium battery CR2032 230mAh (make “VARTA”) (available under ADS-TEC part number: DZ-SONS-04075-1) Ensure the correct polarity when inserting the battery.
  • Page 68 ITC8113 / TabX® 13 Service & support ADS-TEC and its partner companies offer you comprehensive maintenance and support services, ensuring quick and competent support should you have any questions or concerns with regard to ADS-TEC products and equipment. Because ADS-TEC products are also used by partner companies, these devices may have customised configurations.

Table of Contents