Advertisement
Quick Links
Advertisement
Summary of Contents for Toolots HCmaker20
- Page 1 HCmaker20 3D Printer user's manual version V 1.2...
-
Page 2: Table Of Contents
Contents 1. Equipment Architecture......................错误！未定义书签。 2. Equipment Architecture..........................4 installation..............................10 4. Wiring and consumable loading..................... 错误！未定义书签。 Leveling................................. 16 6.Print test.................................17 7.Filament................................. 18 8. Motherboard wiring diagram........................20... - Page 3 Notice Thank you very much for your purchase and support of our 3D printer. You may have purchased some of our other 3D products or have an understanding of 3D printing technology. But we still hope that you can read the product guide carefully, and it contains a lot of important information about the use of the product to give customers a better 3D experience.
- Page 4 4. During the printing process, please note that the machine is equipped with an integrated hot bed heating plate. When using the hot bed function, do not set the hot bed temperature to more than 60 degrees Celsius to avoid burns. If you are under the age of 10, do not use the unit without personal supervision to avoid personal injury.
-
Page 5: Equipment Architecture
1.Equipment architecture 1. Rack 2. Extruder 3. Z-axis right slider 4. Nozzle 5. Print platform 6. LCD display 7. Platform leveling knob 8. Foot pad 9. Broken material detection module 10. X-axis limit Bit switch 11. Z-axis left slider 12. Z-axis limit switch 13. - Page 6 2. Equipment component The whole machine is basically assembled into multiple modules before leaving the factory. We need to assemble these modules into the whole machine we need. number photo model quantity Print platform component Z-axis slider left component Z-axis slider right component...
- Page 7 Extruder mianboard LCD display Power supply...
- Page 8 driven wheel bracket assembly Z axis Limit switch Filament holder Z axis motor...
- Page 9 Z axis Screw fixing plate Z axis fixing plate Bottom vertical bracket, model 2040, length 330mm, ○ ○ 1 、 serial number Bottom lateral bracket, model 2020, length 333mm, serial ○ ○ number 3 、...
- Page 10 Longmen vertical bracket left, model 2040, length 390mm, ○ serial number Longmen vertical bracket right, model 2040, length ○ 390mm, serial number Gantryhorizontal bracket, model 2020, length 333mm, ○ serial number X-axis guide bracket, model 2020, length 343mm, serial ○ number...
-
Page 11: Installation
3.Printer installation Step 1: Install the base frame As shown in the figure: Install the No. 1-4 profile with a M5X30 screw into a square frame, then lock the foot pad with the M6 nut under the four corners of the profile, and then use the four M4X25 screws for the print platform assembly (component No. 1). Installed to the square frame. - Page 12 Step 2: Install the X-axis assembly As shown in the figure: Install the extrusion head assembly into the No. 8 profile, then install the left and right X-axis components with two M4X25 screws on both sides, and then install the belt and clamp it.
- Page 13 Step 3: Install the Z-axis assembly Figure: First step to install profiles No. 5 and No. 6; second step to install No. 12 Z-axis motor components; third step to install X-axis components; fourth step to install No. 11 screw; fifth step to install No. 13 Z-axis Screw rod fixing plate assembly; the sixth step is to install the No.
- Page 14 Step 4: Install the power supply components, motherboard components, and display components As shown in the figure: Install the power supply component on the 7th, then loosen the right front screw and install the 6th display component, and then install the 5th motherboard component. (Note: After the motherboard component is placed close to the front display component, it will prevent the Z-axis from hitting the motherboard when it returns to zero.)
- Page 15 4. Equipment wiring and consumable filling 1. Connect the machine harness as shown below.
- Page 16 2. Insert the consumable into the extruder and insert it into the extruder (as shown)
-
Page 17: Leveling
5. Leveling 1. Prepare → Align the hot bed and wait for the nozzle to return to the original position to move to the left front of the platform. 2. Click Start and the nozzle will move to the four points above the platform. 3. -
Page 18: Print Test
6.Print test 1. Select the model from the menu, click Print, the standby device preheats the hot bed, and then preheats the extruder. After a few minutes, the machine will start printing 2. Observe the printing situation, whether the first layer is printed smoothly... -
Page 19: Filament
7.Put filament 1.Preheat PLA in Prepare 2. Wait for the nozzle temperature to heat up to the predetermined temperature, and select the refueling in preparation... - Page 20 3. Return and feed 4. After refueling, the nozzle can extrude the wire and choose to resume printing.
-
Page 21: Motherboard Wiring Diagram
8. Motherboard wiring diagram...
Need help?
Do you have a question about the HCmaker20 and is the answer not in the manual?
Questions and answers