RITS-N RC400 User Manual

D D
igital igital
Wired Door Key Wired Door Key
(RN-RC400) (RN-RC400)
User's Guide User's Guide
Thank you for purchasing the dual purpose RC400 Wired Digital Door Key / Digital Touch Pad.
1
COMPOSITION & SPECIFICATIONS
Wired Digital Door Key (RC400) 1EA
Mounting screws (4x16) 2EA
Mounting template 1EA
1EA
Connection wire
User's Manual 1 copy
Power supply DC 12~30V, AC 12~24V
DC30V / 1A
Relay contact capacity
-20 ℃ ~50 ℃
Operating temp
Type ISO14443A(Mifare) / 13.56MHz
Power consumption 300mA Under
International Protection
IP54 (Recommend for Indoor Use)
3
GENERAL INFORMATION
: Error : Touch : Ac on / Set
※ Use after removing the protective film
Upper case
Mounting screws
Lower case
Screw bolt for
disassembling
/assembling
Water proof pad (Silicone rubber)
(When assembling the product,
the water proof pad should
Connection
not be twisted)
wire hole
MSIP-CRM-RSN-RN-RC400
Patent application
NO. 10-1456214
2
DIMENSION
41
20
Unit : mm
Disassembling the upper case
Unfasten the screw bolt,
and use a flat blade ( ⊖ )screwdriver
to disassemble it,
as shown in the figure below.
Water proof pad (Silicone rubber)
Between outside gaps
3
OPERATION CHECK & CAUTION
1. Be sure to connect DC12 ~ 30V / AC12 ~ 24V.
2. When it powers on, the LEDs will be displayed sequentially: once all LEDs have been displayed, "beep" sound is heard.
3. Since this system is capacitive touch type, it will not respond to a gloved hand.
4
HOW TO USE
[Card Registration]
1)
①②③④ ⇒ ①②③④ ⇒ # ⇒ ① ⇒ # ⇒ Access card (Serial registration is possible) ⇒ # ⇒ * (end)
①②③④ ⇒ ①②③④ ⇒ # ⇒ ① ⇒ # ⇒ Card address(0001~0500) ⇒ Card ⇒ # ⇒ * (end)
Example) Serial registration : if the first address is [0100], next address is [0101] automatically increase.
[Password Registration]
2)
①②③④ ⇒ ①②③④ ⇒ # ⇒ ② ⇒ # ⇒ Password(4digit) ⇒ # ⇒ * (end)
[Card address Delete]
3)
①②③④ ⇒ ①②③④ ⇒ # ⇒ ③ ⇒ # ⇒ Card address (4digit or serial delete) ⇒ # ⇒ * (end)
[Contact Time]
4)
①②③④ ⇒ ①②③④ ⇒ # ⇒ ⑤ ⇒ # ⇒ 01~60 (01sec.~60sec.) ⇒ # ⇒ * (end)
Example) 5's Setup : 0+5, 20's Setup : 2+0 (2sec at the time of initial release)
[All Card Delete]
5)
①②③④ ⇒ ①②③④ ⇒ # ⇒ ⑥ ⇒ # (end)
[All Password Delete]
6)
①②③④ ⇒ ①②③④ ⇒ # ⇒ ⑦ ⇒ # (end)
[Card or Password Delete]
7)
Card : ①②③④ ⇒ ①②③④ ⇒ # ⇒ ⑧ ⇒ # ⇒ Access Card (Serial possible) ⇒ # ⇒ * (end)
Password : ①②③④ ⇒ ①②③④ ⇒ # ⇒ ⑧ ⇒ # ⇒ Password ⇒ # (Delete) ⇒ * (end)
[Toggle mode contact change]
8)
①②③④ ⇒ ①②③④ ⇒ # ⇒ ②ⓞ ⇒ # ⇒ Set value (ⓞ~①) ⇒ # ⇒ * (end)
Set value - ⓞ : Normal , ① : Toggle mode (ⓞ at the time of initial release)
[Operation mode setting]
9)
①②③④ ⇒ ①②③④ ⇒ # ⇒ ⑨ ⇒ # ⇒ Set value (ⓞ~①) ⇒ # ⇒ * (end)
Set value - ⓞ:NO, ①: NC (ⓞ at the time of initial release)
[Illumination brightness setting]
10)
①②③④ ⇒ ①②③④ ⇒ # ⇒ ①② ⇒ # ⇒ Set value ⓞ~⑨) ⇒ # ⇒ * (end)
Set value -ⓞ: Illumination OFF, ⑨: The highest degree of brightness (② at the time of initial release)
Set the brightness of the illumination at standby state. In case brightness of the illumination is set at OFF,
when touch pad is pressed, number is displayed.
[System number change]
11)
①②③④ ⇒ ①②③④ ⇒ # ⇒ * ⇒ # ⇒ # ⇒ System number in use ⇒ # ⇒ system number to be changed ⇒ # (end)
System Number: Refers to the number ①②③④ used to set menu.
[System Initialization]
12)
①②③④ ⇒ ①②③④ ⇒ * ⇒ # ⇒ Initialization ⇒ Exit after the LEDs blink. ⇒ (end)
5
CONTACT TIME
Yellow
Output Contact
Yellow
White
Wiring
External Input
White
Gray
(DC 12~30V, AC 12~24V)
Power
Gray
(Serial registration)
6
EM LOCK WIRING
EM Lock
Wired Digital
Door Key
Output Contact
Adapter