Subscribe to Our Youtube Channel
Related Manuals for Garment Printer Ink Pearl Lite
Summary of Contents for Garment Printer Ink Pearl Lite
- Page 1 PEARL LITE Use & Care Guide If you have any problems or questions, visit us at www.pearlptm.com For Commercial Use Only...
-
Page 2: Table Of Contents
6. ADJUST DENSITY SETTING ........................8 7. LOADING THE GARMENT......................... 9 8. SPRAY CYCLE ............................9 9. FLUSHING PRETREAT SOLUTION ......................10 10. KEEPING THE PEARL LITE CLEAN ....................... 12 11. ROUTINE MAINTENANCE & ADJUSTMENTS ..................12 12. TROUBLESHOOTING ..........................13 13. WARRANTY ............................. 14... -
Page 3: Important Safety Instructions
1. Important Safety Instructions Your safety and the safety of others are very important. We have provided many important safety messages in this manual. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can injure you or others. This symbol will also alert you of potential damage that may occur to the machine if proper instructions are not followed. -
Page 4: Parts And Features
2. Hose Inlet 7. Shop Vacuum Attachment Connect 1/4” OD hose to inlet for pretreatment Attachment for 2.5” shop vacuum hose. solution supply to the Pearl Lite. 3. Display 8. Platen Micro Adjustment Indicates the Spray Density setting with a range Micro height adjustment for the top platen. -
Page 5: Required Tools And Accessories
3. Required Tools and Accessories 1. All Purpose Cleaner Used to clean the Pearl Lite after use. See “Keeping the Pearl Lite Clean” 2. Shop Rags or Towel Used to clean the Pearl Lite after use. See “Keeping the Pearl Lite Clean”... -
Page 6: Powering The Pearl Lite
WARNING power cord in to the wall outlet. 2. Press the Power Switch (1) to the ON ( | ) position. 3. The Pearl Lite Display (3) will display the last density setting used before the unit was powered off. -
Page 7: Priming The Pearl Lite
5. Priming the Pearl Lite Priming the Pearl Lite is required for proper spray pattern on the garment. If the Pearl Lite is improperly primed, you may not get an even, flat and consistent spray pattern on the garment. 1. To prime the machine, enter the Prime/Purge mode by pressing the Density Up & Down Buttons (4) simultaneously. -
Page 8: Adjust Density Setting
5. Press the Start Button (9) to start the priming sequence. 6. Allow the pressure to build up to ensure proper priming of the machine. 7. Excess pretreatment solution can be poured back into the Pretreatment container. 8. Press the Up and Down Speed Buttons simultaneously to exit the Prime/Purge Mode. The display will change to the last speed setting used before entering the Prime/Purge Mode. -
Page 9: Loading The Garment
3. Push the Platen (5) in to the desired spray length. 8. Spray Cycle The Spray Cycle is the process the Pearl Lite uses to lay a flat and even layer of pretreatment solution on to the garment. 1. With the garment loaded to the desired spray length, press the Start Button (9) to begin the Spray Cycle. -
Page 10: Flushing Pretreat Solution
Spray Cycle. 9. Flushing Pretreat Solution When flushing pretreat solution it is important to follow these steps to ensure proper function the the Pearl Lite. These steps should be followed prior to switching pretreat solution. Failure to follow these DAMAGE... - Page 11 4. Press the Start Button (9) to clear out the pretreat solution in the hose lines. 5. Excess pretreatment solution can be poured back into the pretreatment container. 6. Place the inlet hose in the Distilled Water container. 7. Place a cup under the Nozzle (6) to collect the distilled water. 8.
-
Page 12: Keeping The Pearl Lite Clean
10. Keeping the Pearl Lite Clean It is important to keep the Pearl Lite clean during extended use. The pretreatment solution can build up salt deposits that can inhibit normal operation of the Pearl Lite. 1. Use shop rags or towels to regularly wipe off excess pretreatment inside the machine. -
Page 13: Troubleshooting
Build up of pretreament solution on Normal operation Use towels or rags to regularly clean the inside of the unit. bottom pan of Pearl Lite after spray cycle Table area under the Pearl Lite rear Pump Hoses may have come loose... -
Page 14: Assistance Or Service
This Pearl Lite Limited Warranty supersedes and replaces the limited warranty printed in the Use and Care Guide for products sold within the United States of America and Canada 1 Year For a period of 1 year from date of delivery, when this machine is operated and maintained according to instructions set forth in the Use and Care Guide, Thought Tech will pay for factory specified parts and repair labor to correct defects in materials or workmanship that existed when this machine was purchased. - Page 15 When calling, please know the serial number. This information will help us to better respond to your request. ___________________________________________________________________________________ If you need replacement parts or to order accessories We recommend that you only use Pearl Lite specified parts. To order Pearl Lite specified parts or accessories please contact: sales@pearlptm.com...
Need help?
Do you have a question about the Pearl Lite and is the answer not in the manual?
Questions and answers