Table of Contents
Summary of Contents for Schick CDRPan PC-1000
- Page 1 ® CDRPan FOR PANORAMIC SYSTEMS Installation Instructions for Panoramic Corporation PC-1000 Schick Technologies, Inc. 31-00 47 Avenue Long Island City, New York 11101 (718) 937-5765 (718) 937-5962 (FAX) Part Number B1051101 Rev. –...
- Page 2 Many of the designations used by manufacturers and sellers to distinguish their products are claimed as trademarks. Where those designations appear in this document, and Schick Technologies, Inc. was aware of a trademark claim, the designations have been printed in caps or initial caps.
-
Page 3: Table Of Contents
Contents 1. Introduction....................1 1.1 Welcome ..........................1 1.2 CDRPan System.......................1 1.3 Overview for Installing CDRPan ..................1 1.4 Before You Start Installing CDRPan ................2 2. What You Will Need For Installation ............3 2.1 CDRPan System.......................3 2.2 Tools and Materials......................6 3. Sensor and Codestrip ................7 3.1 Install Sensor Assembly and Sensor Clip ................7 3.2 Route Sensor Cable......................9 3.3 Check Sensor Cable Run....................10... - Page 4 Safety Issues Electrical Concerns CDRPan conforms to national (U.S.) and international standards for electromagnetic compatibility and electrical safety. A complete list of specifications can be found in the CDRPan User’s Guide. Mechanical Considerations The sensor package, the remote module, and the cables of the CDRPan system are mounted outside of the patient area to ensure patient safety and reliable equipment operation.
-
Page 5: Introduction
1.2 CDRPan System The CDRPan system hardware consists of the following components (unless otherwise indicated, all part numbers (P/Ns) refer to Schick Technologies numbers): • CDRPan kit for Panoramic Corp. PC-1000 (P/N B4770050), which includes the sensor, codestrip, other attaching parts, and accessories •... -
Page 6: Before You Start Installing Cdrpan
1.4 Before You Start Installing CDRPan Prior to installing CDRPan on your panoramic system, please perform the following checks. Make sure your panoramic system is operating properly. Familiarize yourself with the installation steps before performing them. Determine the location of your computer. This will be useful when you install the Remote Module and need to run cables between it and your computer. -
Page 7: What You Will Need For Installation
2. What You Will Need For Installation 2.1 CDRPan System To perform the installation procedures in this manual, you will need the following CDRPan parts and assemblies. A. Sensor Assembly B. Drum Codestrip PC-1000 Installation B1051101 Rev. –... - Page 8 C. Remote Module D. Cable Holders and Clamps E. Power Supply B1051101 Rev. – PC-1000 Installation...
- Page 9 F. PCI Board G. Data Cable for PCI Board H. X-ray Filter and Allen Key PC-1000 Installation B1051101 Rev. –...
-
Page 10: Tools And Materials
2.2 Tools and Materials To install the sensor and codestrip, you will need the following tools and materials. A. Allen key (3/32 in.) to adjust clearance between encoder and codestrip. B. Phillips screwdriver to install sensor clip. C. Fine-point marker or pencil to draw guideline for codestrip. B1051101 Rev. -
Page 11: Sensor And Codestrip
3. Sensor and Codestrip 3.1 Install Sensor Assembly and Sensor Clip A. Rotate the drum away from the faceplate aperture. B. Carefully slide the sensor assembly into the aperture until the upper guide is seated firmly at the top of the aperture slit and the lower guide fits in bottom of aperture. C. - Page 12 D. When the sensor clip is positioned, verify the sensor assembly is located correctly, with the motion encoder facing towards the drum. Secure the clip in place using a Phillips screwdriver to tighten 2 screws. MOTION ENCODER B1051101 Rev. – PC-1000 Installation...
-
Page 13: Route Sensor Cable
3.2 Route Sensor Cable A. Use cable clamp to secure sensor cable inside the faceplate. Continue attaching clamps and holders to feed cable along contours of the panoramic machine. B. Route cable to the top of the panoramic machine, following the edge nearest the control panel. -
Page 14: Check Sensor Cable Run
3.3 Check Sensor Cable Run Swivel the arm of the panoramic machine to ensure there is enough slack in the cable for the rotation arm to move freely. Adjust cable if necessary. B1051101 Rev. – PC-1000 Installation... -
Page 15: Prepare To Install Codestrip
3.4 Prepare to Install Codestrip A. Sight the encoder from the edge of the faceplate, and then mark that spot using a fine- point marker or pen. B. Rotate the drum, marking a straight line around it. This line will be used for aligning and mounting the codestrip. -
Page 16: Install Codestrip
3.5 Install Codestrip A. Position the codestrip along the guideline drawn in the step above. B. Remove protective layer from mounting tape and apply the codestrip with adhesive side towards drum. Ensure there are NO kinks or bubbles when the codestrip is applied. -
Page 17: Clearance Adjustments
3.6 Clearance Adjustments A. Adjust the encoder section of the sensor assembly to approximately 1 mm from the codestrip on the drum. Use the Allen key (3/32 in.) to tighten the hinge links on the encoder. B. With X-ray source off, move the rotating arm of the panoramic machine to verify that the sensor cable does not kink, bind, or pull out of clips when the rotating arm is in motion. -
Page 18: Remote Module, Power Supply, And Pci Board
4. Remote Module, Power Supply, and PCI Board 4.1 Install Remote Module 4.1.1 Tools and Materials To install the remote module, you will need velcro patches to secure the module to the top of the panoramic machine, and a screwdriver to secure the sensor cable connector to the remote module. -
Page 19: Install Power Supply
D. The cables on the opposite side of the remote module (power supply and PCI datacable) will be connected after the power supply and the PCI board installation procedures are performed. 4.2 Install Power Supply 4.2.1 Tools and Materials To install the power supply, you will need cable holders and clamps (P/N B4700140) to secure the cable along the side of the panoramic machine and up to the remote module. -
Page 20: Install Pci Board
4.3 Install PCI Board 4.3.1 Tools and Materials To install the PCI board you will need a small screwdriver to remove the cover from your computer; to secure the PCI board in its slot, and to secure one end of the data cable to the remote module and the other end to the PCI board. - Page 21 E. Connect the other end of the data cable to the remote module. Then, use a small secrewdriver to tighten the screws on the connector. F. Refer to the CDRPan User’s Guide (P/N B1051008) to continue with CDRPan system installation. PC-1000 Installation B1051101 Rev.
- Page 22 Remote Module (Secured to top of host machine) Connects to Sensor Assembly, CDRPan PCI card, and Power Supply Sensor Assembly (Mounted to faceplate aperture) Connects to Remote Module Codestrip Assembly (Mounted to drum holder) Power Supply (Placed at base of host machine) Connects to Remote Module and wall power source Also Supplied...
Need help?
Do you have a question about the CDRPan PC-1000 and is the answer not in the manual?
Questions and answers