Brizon Wingflyer 16 Owner's Manual

Brizon Wingflyer 16 Owner's Manual

Folding stepper bike

Advertisement

Quick Links

OWNER'S MANUAL

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Wingflyer 16 and is the answer not in the manual?

Questions and answers

Summary of Contents for Brizon Wingflyer 16

  • Page 1 OWNER’S MANUAL...
  • Page 3: Important Safety Notice

    IMPORTANT SAFETY NOTICE WARNING! PRECAUTIONS: Like any other moving products, riding on the scooter can be a hazardous activity and possibly lead to dangerous situations. Be sure to read the entire manual before riding. In particular, pay attention to the following notices. FOLDING STEPPER BIKE is not a transportation vehicle, and please DO NOT ride in traffic.
  • Page 4 Make sure all components are assembled and secured sturdily and always replace worn or broken parts immediately. Injury may occur if the precautions above are not observed. Rear guard keeps fingers away from moving parts The scooter is for users above 14 years, and the maximum load is 220lbs (100KG).
  • Page 5: Parts And Components

    PARTS AND COMPONENTS PARTS LIST Brake Lever 10 Height adjust lever 20 Chain 11 Positioning button Handle Bar 21 Kickstand • Folding Stem 12 Safety Lock 22 Tire Brake cable clip 13 folding joint 14 Gear box Folding Stem Quick Release Lever 15 Stopper Front Brake 16 Foot Tube...
  • Page 6: Assembly Instruction

    ASSEMBLY INSTRUCTION WARNING! MUST BE ASSEMBLED BY AN ADULT Open the box, and take out the Scooter Unit, Handlebar Set, front tire, pedals and Tool Kits. Please check whether all parts and components are included. Screw sets & Tool Kits Owner’s Manual &...
  • Page 7 B. FRONT WHEEL ASSEMBLY STEP1 Disassemble the Front brake set STEP 2 Set the wheel into the front fork. **The grain direction of front wheel should be same as the rear wheel. Adjust the wheel in center. Tighten the nut on both side.. STEP 3 Assemble the front brake set...
  • Page 8 Step 4 If it's too tight to put the cable in to the slot, please adjust the cable as follow. How to adjust the brake cable: If it's too tight to put the cable in to Loosen the screw counter- the slot clockwise gentely Adjust the cable length...
  • Page 9 C. FOLDING STEM ASSEMBLY How to assemble the folding stem and how to fold it TO ASSEMBLE TO FOLD Lift the head tube up straight.. Turn the safety lock clockwise. Press the quick release lever Pull the lever outwards. inwards firmly. Turn the safety lock counter Fold the head tube back to the clockwise and make sure the...
  • Page 10 C. HANDLEBAR ASSEMBLY Unscrew the nut with the Place the handlebar set Tighten the screws with attached hexagon wrench and stem top cap on the the attached wrench. and open the stem top folding stem...
  • Page 11: Check Before Riding

    F. PUMPING TIRES The front and rear pneumatic tires on the FOLDING STEPPER BIKE come with lower pressure from the factory for transportation reasons. To fill the tires, remove the valve cap and attach the pump to the tire. Alternate between letting air into the tires and checking the pressure to ensure that you get the proper amount.
  • Page 12: How To Ride

    HOW TO RIDE Grasp the handlebar with both of hands, and place one foot on the lower action deck. Push the scooter forward with the other foot. Place the other foot on the other side action deck, take steps with each foot, and FOLDING STEPPER BIKE will be propelled forward.
  • Page 13 Correct Riding The correct riding position should be relaxed standing. Do not lean forward too much. The center gravity of our body is in the rear. Slide To Ride (Beginner) Put one foot on the pedal, use the other foot to slide the scooter.
  • Page 14 Advanced Riding Push the pedal a little with one foot and lift the other foot and push. Start to ride. Stop In Process of riding Stop Situation When you see a situation ahead in the road, press the brake to being to slow down. Lift one foot off the pedal and place it on the ground.
  • Page 15 USE GUIDE AND MAINTENANCE Rotate the bearings and wheels to see whether they are workable, and do some adjustments or add lubricant if it’s needed after the first 2 week’s use. It is not suggested to cover the painted metal tube with plastic bags or cloth. DO NOT use wet cloth to clean the painted body to prevent loss of gloss or peeling off.

Table of Contents