Related Manuals for PI Manufacturing HDMI-HGWI-200M
Summary of Contents for PI Manufacturing HDMI-HGWI-200M
- Page 1 PI MANUFACTURING Powered by In nite Solutions Wireless HDMI Extender HDMI-HGWI-200M Installation Manual PI Manufacturing, www.pimfg.com...
-
Page 2: Table Of Contents
Contents Product Features Important Safety Instructions ............3 What’s Included ................... 4 Overview ................... 5 Panel Illustration ................5-6 Setup Instructions ........... 7-8 Technical Speci cations ..............9-11 Troubleshooting ................ 12 FCC ................ 13 PI Manufacturing, www.pimfg.com... - Page 3 - The slots and openings on this product are for ventilation purposes. Do not cover or block them as this could cause overheating. - There are no user-serviceable parts in this product. - If servicing is required, always refer to a quali ed service technician. PI Manufacturing, www.pimfg.com...
-
Page 4: What's Included
What’s Included Product Features 2 - TX / RX HDMI Extenders 2 - HDMI Cables 2 - 5V 2.5A Power Adapters 2 - IR Emitter / Receiver 1 - User Manual PI Manufacturing, www.pimfg.com... -
Page 5: Overview
Built-in USB ports allow an additional keyboard and mouse to be plugged in for control if necessary. The wireless HDMI extender features low end to end latency (16ms), and can be used for various commercial or residential applications faced with wired limita- tions. PI Manufacturing, www.pimfg.com... -
Page 6: Panel Illustration
5. HDMI In (HDMI Source) 6. HDMI Out (HDMI Display) Receiver 1. On/O Switch 2. 5V DC In Power 3. IR (IR receiver) 4. USB (Keyboard or Mouse) 5. USB (Keyboard or Mouse) 6. HDMI Out (HDMI Display) PI Manufacturing, www.pimfg.com... -
Page 7: Setup Instructions
Step 6. Connect the IR receiver cable and place it near the television where you will point the remote control. Step 7. Connect the 5V DC power adapter. Step 8. Turn on the power switch on for both the transmitter and receiver. PI Manufacturing, www.pimfg.com... -
Page 8: Setup Instructions
Step 1: Plug in a Micro-USB B Male to USB Type A Male cable from the transmitter to the HDMI source (Note: The source needs to be able to support USB keyboards / mice). Receiver Step 2: Plug in the USB keyboard / mouse on the USB ports PI Manufacturing, www.pimfg.com... -
Page 9: Technical Speci Cations
480p / 60Hz 480i / 60Hz HDCP Up to 656ft (200m) at 1080p Transmit Distance (clear line of sight) Audio format 48/44.1 KHz, 16bit digital audio System Latency 16ms IR Frequency 20-60KHz Detachable external antennas Antenna (5dBi) PI Manufacturing, www.pimfg.com... - Page 10 Operating Temperature 0°C ~ 40°C (32°F ~ 104°F) Storage Temperature -40°C ~ 70°C (-40°F ~ 158°F) Product Dimensions 9.5 x 13.9 x 2cm (each) (L x W x H) Weight 120g (0.26 lbs / each) Enclosure Plastic PI Manufacturing, www.pimfg.com...
-
Page 11: Technical Speci Cations
Red light: Power is o or abnormal Blue & Red Light (Power) Blue light: Power is on and detected HDMI input source Blinking orange: Unpaired Orange (Pairing) Solid orange: Paired Solid green: WiFi working Green (WiFi) Flickering green: Data is transferring PI Manufacturing, www.pimfg.com... -
Page 12: Troubleshooting
- The IR cables are based on a 20-60kHz frequency. This should support most IR remote controls in the market USB Keyboard / Mouse not Working - Make sure the TX side is connected via a Micro-USB to USB Type A cable PI Manufacturing, www.pimfg.com... - Page 13 The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be colocated or operating in conjunction with any other antenna or transmitter. PI Manufacturing, www.pimfg.com...