Summary of Contents for TELINK SEMICONDUCTOR EVK TLSR8266BR56
- Page 1 Application Note： User Guide for Telink Burning EVK TLSR8266BR56 AN-18010500-E2 Ver 1.1.0 2018/7/27 Brief： This document is the user guide for Telink burning EVK TLSR8266BR56.
- Page 2 Telink Semiconductor does not assume any liability arising out of the application or use of any product or circuit described herein; neither does it convey any license...
- Page 3 User Guide for Telink Burning EVK TLSR8266BR56 Revision History Major Changes Date Author Version 1.0.0 Initial release 2018/3 HZF, Cynthia 1.1.0 Updated section 3 Schematic 2018/7 HZF, Cynthia AN-18010500-E2 Ver 1.1.0...
-
Page 4: Table Of Contents
User Guide for Telink Burning EVK TLSR8266BR56 Table of contents Brief Introduction ....................4 Connection Guide ....................5 Supply power for TLSR8266BR56 ..............5 Download firmware into DUT via TLSR8266BR56 ........... 6 Communication interface ................8 Schematic........................ 9 Table of figures Figure 1 TLSR8266BR56 photo ................ -
Page 5: Brief Introduction
User Guide for Telink Burning EVK TLSR8266BR56 1 Brief Introduction This document presents guide on how to use Telink TLSR8266-based burning EVK “TLSR8266BR56” as an adapter to download firmware into target board (DUT). Button Top view Pin header miniUSB interface... -
Page 6: Connection Guide
User Guide for Telink Burning EVK TLSR8266BR56 2 Connection Guide 2.1 Supply power for TLSR8266BR56 Connect the miniUSB interface of the TLSR8266BR56 with PC USB via a mini USB cable. miniUSB interface Connect to PC USB via USB cable Figure 2... -
Page 7: Download Firmware Into Dut Via Tlsr8266Br56
User Guide for Telink Burning EVK TLSR8266BR56 2.2 Download firmware into DUT via TLSR8266BR56 The TLSR8266BR56 is used as burning adapter and it is preloaded with the “8266_evk.bin”. Method 1: Connect the TLSR8266BR56 with DUT via Single wire (Swire). 1. Connect the miniUSB interface of the TLSR8266BR56 with PC USB via a mini USB cable. -
Page 8: Figure 4 Connection Chart 2 To Download Fw Into Dut Via Tlsr8266Br56
User Guide for Telink Burning EVK TLSR8266BR56 Method 2: Connect the TLSR8266BR56 with DUT via USB instead of Swire. This method only applies to the DUT with USB interface (e.g. dongle board). 1. Connect the miniUSB interface of the TLSR8266BR56 with PC USB via a mini USB cable. -
Page 9: Communication Interface
User Guide for Telink Burning EVK TLSR8266BR56 2.3 Communication interface SPI/I2C interface UART interface Figure 5 TLSR8266BR56 communication interface Please refer to the schematic in section 3 for the connection guide of SPI/I2C/UART interface. AN-18010500-E2 Ver 1.1.0... -
Page 10: Schematic
User Guide for Telink Burning EVK TLSR8266BR56 This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation.
Need help?
Do you have a question about the EVK TLSR8266BR56 and is the answer not in the manual?
Questions and answers