Table of Contents
Advertisement
Quick Links
IN-LINE FIGURE 700 QUICK OPENING CLOSURE
INSTALLATION, OPERATIONS AND MAINTENANCE MANUAL
SECTION TWO: INSTALLATION INSTRUCTIONS
SECTION THREE: OPERATION INSTRUCTIONS
SECTION FOUR: MAINTENANCE INSTRUCTIONS
SECTION FIVE: STORAGE INSTRUCTIONS
THIS DOCUMENT HAS BEEN MADE AVAILABLE TO PROVIDE ADDITIONAL
INFORMATION FOR ANY IN-HOUSE TRAINING PROGRAM ON THE INSTALLATION,
OPERATION AND MAINTENANCE OF THE IN-LINE QUICK OPENING CLOSURE AND IS
NOT INTENDED TO SUPERSEDE THE SAFETY POLICIES OR PROCEDURES OF THE END-
USER.
ALL SUPERVISORS, OPERATORS, WELDERS AND OTHER FIELD PERSONNEL THAT ARE
DIRECTLY INVOLVED IN THE INSTALLATION, OPERATION AND MAINTENANCE OF THE
IN-LINE QUICK OPENING CLOSURE SHOULD RECEIVE AND REVIEW THIS INFORMATION
AS PART OF ANY TRAINING PRIOR TO THE INSTALLATION AND OPERATION OF THESE
DEVICES.
FAILURE TO FOLLOW SAFETY GUIDELINES OR PROCEDURES
MAY RESULT IN SEVERE INJURY OR DEATH.
ADDITIONAL COPIES OF THIS MANUAL MAY BE OBTAINED AT NO CHARGE BY
CONTACTING:
©
In-Line Flow Products Limited
All rights reserved
Printed in Canada
SECTION ONE: SAFETY INFORMATION
IMPORTANT
IN-LINE FLOW PRODUCTS LIMITED
TEL: (780) 490-5337
FAX: (780) 490-5314
Revision 1 03/2016
Page 1 of 16
Advertisement
Table of Contents
Summary of Contents for In-Line Flow Products FIGURE 700
- Page 1 IN-LINE FIGURE 700 QUICK OPENING CLOSURE INSTALLATION, OPERATIONS AND MAINTENANCE MANUAL SECTION ONE: SAFETY INFORMATION SECTION TWO: INSTALLATION INSTRUCTIONS SECTION THREE: OPERATION INSTRUCTIONS SECTION FOUR: MAINTENANCE INSTRUCTIONS SECTION FIVE: STORAGE INSTRUCTIONS IMPORTANT THIS DOCUMENT HAS BEEN MADE AVAILABLE TO PROVIDE ADDITIONAL...
-
Page 2: Section One Safety Information
Avoid installing the Closure where the bore is directed towards buildings and equipment or where personnel or the public have access. © In-Line Flow Products Limited Revision 1 03/2016 All rights reserved Page 2 of 16 Printed in Canada... - Page 3 Closure. DO NOT OVERTIGHTEN. Spanner wrenches for all Closures are available and are extremely effective for safely obtaining a tight seal. © In-Line Flow Products Limited Revision 1 03/2016 All rights reserved Page 3 of 16 Printed in Canada...
-
Page 4: Section Two Installation
Weld Hub prior to disassembly to prevent mixing of assemblies. 5. Where required, use lifting equipment of sufficient size and stability when performing installation and ensure operation by trained personnel. © In-Line Flow Products Limited Revision 1 03/2016 All rights reserved Page 4 of 16... - Page 5 Closure Weld Hub. 9. Remove the Pressure Alert Fitting from the Weld Hub and store with the Cap/Hinge assembly. © In-Line Flow Products Limited Revision 1 03/2016 All rights reserved Page 5 of 16...
- Page 6 Closure Weld Hub. 6. Remove the Pressure Alert Fitting from the Weld Hub and store with the Cap/Hinge assembly. © In-Line Flow Products Limited Revision 1 03/2016 All rights reserved Page 6 of 16...
- Page 7 Do not assemble or operate with the threads dry. Grease Hinge components and assemble Hinge Arm/Cap Assembly into the Weld Hub Hinge. Do not replace the Seal at this point. © In-Line Flow Products Limited Revision 1 03/2016 All rights reserved Page 7 of 16...
- Page 8 (preferably) or other anti-seize lubricant. Do not assemble or operate with the threads dry. Do not replace the Seal at this time. © In-Line Flow Products Limited Revision 1 03/2016 All rights reserved Page 8 of 16...
- Page 9 7. Screw the Cap on to the Weld Hub and tighten until alignment of the marks made in Step 7 is made. Do not tighten past these marks. © In-Line Flow Products Limited Revision 1 03/2016 All rights reserved Page 9 of 16...
-
Page 10: Section Three Operation Instructions
Closure opening. Trapped or stuck objects within the system may result in projectiles if they suddenly break loose and are ejected through the Closure. © In-Line Flow Products Limited Revision 1 03/2016 All rights reserved Page 10 of 16... - Page 11 Pressure Alert Fitting may require replacement. 6. Pressurize the system and check for leakage. If leakage occurs, perform the maintenance operation as outlined in Section Four – Maintenance Instructions. © In-Line Flow Products Limited Revision 1 03/2016 All rights reserved Page 11 of 16...
-
Page 12: Section Four Maintanence Instructions
8. If Hinge adjustments are required, with the Closure closed halfway, loosen the Hinge Stop and lift the Hinge Arm and Cap simultaneously and re-tighten. Cycle the Closure and continue to adjust until smooth operation is achieved. © In-Line Flow Products Limited Revision 1 03/2016 All rights reserved Page 12 of 16... -
Page 13: Section Five Storage Instructions
4. It is important that the Closure threads remain clean and protected with clean grease during storage, disassembly, installation and assembly. Dirt, weld slag, etc. will damage threads if entrained within the grease during Head removal or make-up. © In-Line Flow Products Limited Revision 1 03/2016 All rights reserved Page 13 of 16... -
Page 14: Terms And Conditions
TERMS AND CONDITIONS 1. In-Line Flow Products Ltd. (“In-Line”) warrants its products against defects in material and workmanship for a period of one calendar year after date of shipment when the products are properly installed, operated and maintained within the limits for which they were designed, manufactured and in accordance with In-Line’s written instructions. - Page 15 In-Line, and shall be returned to In-Line immediately upon request. © In-Line Flow Products Limited Revision 1 03/2016 All rights reserved Page 15 of 16...
- Page 16 12. This is the sole and exclusive warranty given by In-Line with respect to the products offered and is in lieu of and excludes all other warranties, express or implied. For further assistance or additional copies of this document, please contact: IN-LINE FLOW PRODUCTS LIMITED EDMONTON, ALBERTA, CANADA TEL: (780) 490-5337 FAX: (780) 490-5314 ©...