Download
Share
Print this page
Colortrac SingleSensor CIS Instruction Manual
  1. Manuals
  2. Brands
  3. Colortrac Manuals
  4. Accessories
  5. SingleSensor CIS
  6. Instruction manual

Colortrac SingleSensor CIS Instruction Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
SCIM-003
Issue 1
C
o
l
o
r
C
o
l
o
r
S
S
I
n
s
I
n
Colortrac Ltd
SingleSensor Instruction Manual
This is a confidential controlled document and is the property of Colortrac Ltd.
It is not to be copied or reproduced in part or whole.
t
r
a
c
t
r
a
c
i
n
g
l
e
S
i
n
g
l
e
S
t
r
u
c
t
i
o
s
t
r
u
c
t
i
S
C
S
c
S
C
S
e
n
s
o
r
e
n
s
o
r
n
M
a
o
n
M
a
Page 1 of 23
Date: 12/02/14
a
n
n
c
a
n
n
C
I
S
C
I
S
n
u
a
l
n
u
a
l
e
r
e
r

Advertisement

loading
Need help?

Need help?

Do you have a question about the SingleSensor CIS and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Colortrac SingleSensor CIS

  • Page 1 SCIM-003 Colortrac Ltd Page 1 of 23 SingleSensor Instruction Manual Issue 1 Date: 12/02/14 This is a confidential controlled document and is the property of Colortrac Ltd. It is not to be copied or reproduced in part or whole.
  • Page 2 Technical Support, Colortrac Ltd.  Colortrac Ltd shall not be liable for any damages, errors, issues or events that result from the use of the equipment or this manual. Page 2 of 23...

  • Page 3: Table Of Contents

    SC Scanner Instruction Manual  CONTENTS Tools Required ......................... 4 Photos Information ........................4 SingleSensor CIS Assy ......................5 Calibration ..........................20 Auto-stitch ..........................22 Page 3 of 23...

  • Page 4: Tools Required

    SC Scanner Instruction Manual Tools Required To maintain the SC Scanner the tools listed below are required. The tools are generally available; they are not the responsibility of Colortrac to supply. 1. Wristband 2. Pencil   Anti-static and cable.

  • Page 5: Singlesensor Cis Assy

    SC Scanner Instruction Manual SingleSensor CIS Assy 1. To remove the Top Lid Cover, first depress the Lid Latches at either end of the Lid Assembly. 2. Allow the Lid Assembly to gently open. 3. Carefully remove the 2 x M4 screws holding the left end of the Top Lid Cover.
  • Page 6 SC Scanner Instruction Manual 5. Close the Lid Assembly making sure both Lid Latches lock securely. 6. Carefully lift the Top Lid Cover off from the Lid Assembly. 7. Remove the Aluminium EMC Tape covering the cables to the Main Board. 8.
  • Page 7 SC Scanner Instruction Manual 9. WARNING: Gently lift the Main Board Cover to reveal the Mains Connector. Release the Mains Connector from the Main Board. NOTE: Care needs to be taken with the Suppressor leads on the Main Board cover as they can be broken with repeated or excessive movement.
  • Page 8 SC Scanner Instruction Manual 13. Gently pull the ribbon cable from the connector. 14. Disconnect the 4 x LED cables J10 - 13. 15. Remove the M3 x 4 screws holding the Control Board Bracket Cover. Page 8 of 23...
  • Page 9 SC Scanner Instruction Manual 16. Remove the Control Board Bracket Cover. 17. Before removing the Control Board Bracket Assembly, use a pencil to mark its position. 18. Remove the 4 x M3 screws holding the Control Board Bracket Assembly to the Lid Assembly.
  • Page 10 SC Scanner Instruction Manual 19. Rotate the Control Board Bracket Assembly to gain access to the Control Board and cables. 20. Disconnect the 4 x Paper Sensor Cables and the Control Board Cable from the Main Board. Remove the Control Board Bracket and store safely until refitting.
  • Page 11 SC Scanner Instruction Manual 23. While removing the screws from the Gas Pistons at both ends of the Lid Assembly, make sure your free hand is holding the Lid Assembly to prevent it dropping down. Once free lift the Lid to the 90deg position.
  • Page 12 27. Remove the 2 x M3 screws from the right end of the SingleSensor CIS Assy. NOTE: With your free hand, hold the SingleSensor CIS Assy in place to prevent it dropping and being damaged. 28. Gently remove the SingleSensor CIS Assy from the Lid Assembly.
  • Page 13 30. Gently pull the remaining length of the LED cables through from the Lid Assembly. 31. Feed the LED cables from the new SingleSensor CIS Assy through the Lid Assembly before lifting it into place, continuing to pull the cables through the Lid...
  • Page 14 SC Scanner Instruction Manual 33. While holding the SingleSensor CIS Assy flat in place, refit the 2 x M3 screws into the right end, but do not tighten at this stage. 34. Refit the 2 x M3 screws into the left end, but do not tighten at this stage.
  • Page 15 SC Scanner Instruction Manual 38. Rotate and locate the Control Board Bracket Assembly to the pencil lines marked out before, then refit the 4 x M3 screws to hold the Control Board Bracket Assembly to the Lid Assembly. 39. Fit the Control Board Bracket Cover and make sure all the cables are in the cut out.
  • Page 16 SC Scanner Instruction Manual 42. When the CIS Ribbon cable is fully in place, secure it by pressing down both sides of the locking plate. 43. Reconnect the 4 x LED cables J10 - 13, ensuring the correct cable is inserted in the correct plug.
  • Page 17 SC Scanner Instruction Manual 45. Reconnect the Power Connector. Then lower the Main Board Cover into place. 46. After making sure all the cables are in their appropriate cutout, and the USB connector is also in it’s cutout in the cover, fit 4 x M3 screws to hold the Main Board Cover in place.
  • Page 18 SC Scanner Instruction Manual 48. Lower the Lid Assembly, by loosen off the screws in the Hinge Brackets, at both ends, while holding the Lid Assembly, until the lid can move freely. 49. Lower the Lid Assembly to the correct position to reattach the 3 x M4 screws of the Right Gas Piston.
  • Page 19 SC Scanner Instruction Manual 52. Reconnect the Power and USB cables to the Scanner and power up the scanner and Utilities Program. 53. Run the Calibration as described in chapter “4 Calibration” page 20. 54. Run the Auto-stitch as described in chapter “5 Auto-stitch” page 22. 55.

  • Page 20: Calibration

    SC Scanner Instruction Manual Calibration 1. Open the Lid Assembly and clean the SingleSensor Glass Sub-Assy. Close the Lid Assembly. 2. Insert the Calibration Target so that the black part section is inserted first, face NOTE: It is necessary to remove the Magnetic Paper Guide AND the Document Return Guide (if it is fitted to the scanner) so the target can pass through the scanner...
  • Page 21 SC Scanner Instruction Manual 5. Click ‘OK’ to except the message. 6. After approx. 4 minutes, the ‘Calibration’ (or Normalisation) is complete. During calibration , the target will move through the scanner in stages several times. Page 21 of 23...

  • Page 22: Auto-Stitch

    SC Scanner Instruction Manual Auto-stitch 1. To enter the second level utilities Click ‘Utilities’ at the bottom of the front page. 2. Insert the Calibration Target so that the black section is in first, and face up. NOTE: It is necessary to remove the Magnetic Paper Guide AND the Document Return Guide (if it is fitted to the scanner) so the target can pass through the scanner...
  • Page 23 SC Scanner Instruction Manual 4. Click ‘OK’ to except the message. 5. On completion, click the ‘OK button. Useful Information:  FB stitch range: 0 – 32  LR stitch range: 0 – 88 Page 23 of 23...