Table of Contents
Advertisement
Quick Links
THANKS FOR PURCHASING OUR PRODUCT
DC INVERTER
AC TIG/DC TIG
DC MMA
WELDING MACHINE
OPERATION INSTRUCTIONS
( be suitable for 3 x380V)
CV. ANUGRAH DUTA NIAGA
J a l a n A r i e f R a c h m a n H a k i m 5 1 , R u k o 2 1 B l o k D - 1 K l a m p i s , S u k o l i l o , S u r a b a y a
T e l p : ( 0 3 1 ) 5 9 9 0 0 8 9 ; 5 9 9 7 2 5 9
F a x : 0 3 1 - 5 9 6 6 0 9 9
W e b S i t e : w w w . a d n s b y . c o . i d
E m a i l : a d n _ o f f i c e @ y a h o o . c o m
Advertisement
Table of Contents
Summary of Contents for ADN WEIRO SUPERTIG315EX
- Page 1 THANKS FOR PURCHASING OUR PRODUCT DC INVERTER AC TIG/DC TIG DC MMA WELDING MACHINE OPERATION INSTRUCTIONS ( be suitable for 3 x380V) CV. ANUGRAH DUTA NIAGA J a l a n A r i e f R a c h m a n H a k i m 5 1 , R u k o 2 1 B l o k D - 1 K l a m p i s , S u k o l i l o , S u r a b a y a T e l p : ( 0 3 1 ) 5 9 9 0 0 8 9 ;...
-
Page 2: Safety Precautions
SAFETY PRECAUTIONS Follow these precautions carefully. Improper use of any welder can result in injury or death. 1. ONLY CONNECT WELDER TO A POWER SOURCE FOR WHICH IT WAS DESIGEND. The specification plate on the welder lists this information. When welding outdoors only use an extension cord intended for such use. -
Page 3: Main Usage And The Range Of Usage
MAIN USAGE AND THE RANGE OF USAGE ， （ SUPERTIG315EX Welder is triple functional machine used as MMA AC TIG, DC TIG PULSE TIG)Welder. All ferrous metals copper, Aluminium ,titanium and stainless steel material can be omnibearing welding in all position.The welding current is stable and stepless adjustable.The welding seam is nice. -
Page 4: Operating Condition
Ⅲ. OPERATING CONDITION AND WORK SURROUNDING 1. Operating condition: ± 。 Voltage of power source: 3~ 380V 10% Frequency: 50/60Hz Reliable grounding protection 2.Work surrounding ① ℃ . relative humidity: not more than 90 %( average monthly temperature not more than 20 ) ②... - Page 5 1.indication of welding current 2.power switch 3.pulse (base) current regulator 4.current regulator 5.Pulse time On 6.pulse Freq. regulator 7.indicating light of power 8.O.T. indicating light 9. current up-slope time regulator10.current down-slope time regulator 11. post flow time regulator 12.STICK/TIG/ switch 13.AC balance 14.output"+"15.AC square wave Frequency 16. arc force 17.argon out 18.argon arc control 19.
-
Page 6: Clearing Before Welding
1.1 CLEARING BEFORE WELDING Tungsten argon an welding is very sensitive to surface contamination of filled metal.Therefore before welding is carried out, grease, paint and coating on the surface,lubricant for machining and oxidized film should be removed. 1.2 DC ARGON ARC WELDING When you need process at DC tig,please switch "pulse off/low/high"... - Page 7 ⑥ .Gas connecting and testing,are generating and are blowing off etc. are all the same as DC are welding. 1.4 PULSE ARGON TUNGSTEN WElDING PROCESS (only for reference) Ip--pulse current CUR. welding process Ib--base current tp--width time of pulse current tp tb down-slope up-slope...
-
Page 8: Ac Argon Arc Welding
③ .Selection of welding parameters Except for pulse current and the width time (Pulse time On) as well as pulse frequency ,welding parameters of pulse argon gas tungsten arc welding are as same as general tungsten DC argon are welding. Pulse current increasing means electric arc can obtain greater penetration ability.But too much current can cause local melting of tungsten electrode.Generally,welding current required for DC tungsten argon are welding or greater current is used. - Page 9 A. POSITIVE CONNECTION B . NEGATIVE CONNECTION WELDER WELDER ELECTRODE ELECTRODE HOLDER HOLDER WORKPIECE WORKPIECE ④.Connecting input power for the welder, then switch on the power and current indicating light "7" is on . ⑤ .Pay attention to rated welding current and rated duty cycle of the welder. Overload is not allowed.
-
Page 10: Problem Solving
Trouble Causes Problem Solving 1.No electricity input 1.Check incoming line . Power lamp not light 2.Switch of welder fails. 2.Replace the switch 1.Fan power line is off. 1.Reconnect the line 2.Enclosure blocks the fan due to Fan not rotating 2.Reform the enclosure . deformation 3.Replace the fan 3.The fan fails. -
Page 11: Packing List
Ⅸ .ACCESSORIES:SEE PACKING LIST,PLEASE PACKING LIST ★★★★★★★★★★★★★★★★★★★★★★★★ SUPERTIG315EX Ground clamp TIG welding torch Welding holder gas inlet pipe Operation instructions Certificate of quality ━━━━━━━━━━━━━━━━━━━━━━━ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ Certificate of quality Name of product: ACTIG/DCTIG/DC STICK MACHINE Type of product:... - Page 12 Do not touch electrically live parts or Keep flammable materials away. Wear eye, ear and body protection. WARNING electrode with skin or wet clothing. Insulate yourself from work and ground. Spanish No toque las partes o los electrodos Mantenga el material combustible Protéjase los ojos, los oídos y el AVISO DE bajo carga con la piel o ropa moja-...
- Page 13 Keep your head out of fumes. Turn power off before servicing. Do not operate with panel open or Use ventilation or exhaust to guards off. WARNING remove fumes from breathing zone. Spanish Los humos fuera de la zona de res- Desconectar el cable de ali- No operar con panel abierto o AVISO DE...
Need help?
Do you have a question about the WEIRO SUPERTIG315EX and is the answer not in the manual?
Questions and answers