Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Sunstream Mini
Summary of Contents for Sunstream Mini
- Page 1 Assembly Manual www.infraredsaunas.co.nz Tel 021 224 8020...
- Page 2 Prepare & Position the Sauna Floor If you are assembling your sauna on a hard surface floor it is recommended that you apply the included adhesive felt pads to the bottom of the sauna floor. Place the sauna floor in the desired location. It is necessary to position the floor out from your walls for assembly and move the sauna following assembly. It is important that the sauna floor is level. Checking with a large level is recommended. If the floor is not level, shimming or other remedies should be applied before assembling the sauna. www.infraredsaunas.co.nz Tel 021 224 8020...
- Page 3 Left Side Wall Place the left side wall on your floor behind the sauna floor base. Front Wall Insert the front wall (with window) into the channel in the sauna floor base www.infraredsaunas.co.nz Tel 021 224 8020...
- Page 4 Connect Left Side Wall and Front Wall Cinch the left side wall and the front wall together by applying pressure on the outside of the side wall with your knee while assistant gently pushes the edge of front wall with their foot. Slide the front wall upward approx. 3/4” with right hand while holding the side wall down with your left hand. There are two sets of fasteners to join the saunas' corners together. After lowering the front wall, check to ensure that both sets of fasteners have connected by looking at the corner inside of the sauna. It is possible to connect one set of fasteners and miss the other. If there is an obvious gap in the corner between the two walls the fasteners have not connected and the raising and lowering procedure will need to be repeated. www.infraredsaunas.co.nz Tel 021 224 8020...
- Page 5 Back Wall Repeat the procedure to connect the back wall to the left side wall Right Side Wall (with door) Insert the right side wall into the channel in the sauna floor base www.infraredsaunas.co.nz Tel 021 224 8020...
- Page 6 Connect the Right Side Wall (door wall) to Back Wall It is easiest to connect one corner of the side wall (door wall) at a time It is recommended that the assistant stablizes the sauna on opposite side while connecting the door wall Connect the Right Side Wall (door wall) to the Front Wall www.infraredsaunas.co.nz Tel 021 224 8020...
- Page 7 Connect the front wall heater electrical lead to the floor base. Ensure hat the threaded cuff of the connector is fully screwed onto the floor base connector. UnderBench Electrical Connect all electrical cords to the main power supply box recessed in the floor. www.infraredsaunas.co.nz Tel 021 224 8020...
- Page 8 Remove Side Wall Heater Guards The wooden lattice work in front of the heaters is referred to as the heater guard. These are held in place with strong magnets. It is necessary to remove the heater guards from the two side walls in order to install the leg heater and the sauna bench. Leg Heater Install the leg heater by lowering it into the holding brackets mounted on the side walls. Plug leg heater into the power supply box in floor. www.infraredsaunas.co.nz Tel 021 224 8020...
- Page 9 Install the Sauna Bench Reinstall the Side Wall Heater Guards www.infraredsaunas.co.nz Tel 021 224 8020...
- Page 10 Prepare the Sauna Roof Remove the one panel on the left side of roof to access electrical connections. Install Sauna Roof Lower the roof into place by first fitting the right side of roof (door side). Keep the left side of roof elevated to enable feeding of electrical connection from wall through the roof. www.infraredsaunas.co.nz Tel 021 224 8020...
- Page 11 Roof Wires Before lowering the roof it is necessary to feed the wire up through the hole in the sauna roof as pictured. This is easiest accomplished with one person holding the weight of the roof while the other feeds the wire through the hole. When the wire is fed entierly through the roof, lower roof into place taking care not to pinch the wire between the roof and the front wall Roof Electrical Take the wire that was fed from the side wall through the roof and make connection on the roof. This connection is the 12 volt power for the LED reading light and the Bluetooth audio receiver/ amplifier. www.infraredsaunas.co.nz Tel 021 224 8020...
- Page 12 Bluetooth Audio Receiver Music can be piped to the speakers in the sauna two different ways, either wireless via the Bluetooth receiver or by directly connecting your device (smart phone, tablet, laptop etc.) with an audio cord (red audio cord not included) Bluetooth Mode: Search for and pair your device's Bluetooth to 'BT speaker'. Direct Connect Mode: Connect your device to the saunas' speakers via your device's headphone jack by inserting an audio cord into the BT circuit board. This will deactivate the Bluetooth receiver. www.infraredsaunas.co.nz Tel 021 224 8020...
- Page 13 Reinstall the roof panels and feed your audio cord through the hole in roof if you have decided NOT to use Bluetooth www.infraredsaunas.co.nz Tel 021 224 8020...
- Page 14 Control Panel www.infraredsaunas.co.nz Tel 021 224 8020...
- Page 15 Interior Control Panel Temperature Sensor FRAGILE DO NOT TOUCH www.infraredsaunas.co.nz Tel 021 224 8020...
- Page 16 Connecting the sauna to your house power supply When the sauna is plugged into you wall outlet the red Power Indicator light on the control panel will be on. The Bluetooth audio receiver on the roof will make a beeping noise its indicator light will turn on. ON/OFF for Heaters Push the POWER button to turn the sauna heaters ON. The various displays will come on. The sauna heaters will remain ON until the timer runs down to 00. The sauna heaters can be turned OFF at any time by pushing the POWER button. Timer Adjustment The default time is 60 minutes. Press + or to change the Timer setting. The maximum setting is 60 minutes. The minimum setting is 5 minutes. Pre Heat Sun Stream Infrared Saunas are typically used by preheating the sauna for 2030 minutes. Thermostat Adjustment Press + or to change the Thermostat setting. Increase Thermostat Setting: Press the + button to increase the temperature by 1 degree C increments. The maximum setting is 65 C. Decrease Thermostat Setting: Press the button to decrease the temperature by 1 degree C increments. The minimum setting is 25 C. www.infraredsaunas.co.nz Tel 021 224 8020 ...
- Page 17 Thermometer /Thermostat Display When the POWER button is turned ON the digital display will show the Thermometer reading. Anytime the + and buttons are pushed the Thermostat setting display will show. After setting the thermostat the display will return to displaying Thermometer reading. Temperature Control When the interior air temperature is below the Thermostat set temperature, the heaters will remain ON. When the interior temperature is higher than the Thermostat set temperature, the power to the heaters will be turned OFF. The heater panels will begin to cool down, air temperature and Infrared levels will slowly drop until the Thermostat is activated and the power to the heaters will be turned back on. AII (Adjustable Infrared Intensity) The Intensity button on the control panel will adjust the Infrared intensity much like a dimmer switch for a household light. Press the Intensity button to select 100%, 75% or 50 % levels of Infrared intensity for different purposes and individual needs. www.infraredsaunas.co.nz Tel 021 224 8020...
- Page 18 Enjoy your new Sun Stream Infrared Sauna ! www.infraredsaunas.co.nz Tel 021 224 8020...
Need help?
Do you have a question about the Mini and is the answer not in the manual?
Questions and answers