Subscribe to Our Youtube Channel
Related Manuals for Intrasonic Technology V510
Summary of Contents for Intrasonic Technology V510
- Page 1 INSTALLATION AND OPERATION INSTRUCTIONS V510 Smartphone Video Doorbell 4-Wire IP AHD Video Door Phone 10'' Display Series User Manual...
- Page 2 This warranty extends to the original user or subsequent Intrasonic Technology will replace or repair the product at its discretion at no charge with a owner of the product during the warranty term. Intrasonic Technology will replace or repair reconditioned or new product.
-
Page 3: Table Of Contents
Table of Contents Table of Contents 2.4.6.2 Upgrade ................26 2.4.7 User ..................26 2.4.8 Default ..................29 LIMITATION OF LIABILITY................1 2.4.9 Information ................29 DISCLAIMER OF WARRANTY.................1 2.4.10 Save/Exit.................29 SAFETY INSTRUCTIONS................1 3. Web Browser Operation................30 CARING FOR THE ENVIRONMENT BY RECYCLING........2 3.1 Feature.....................30 COPYRIGHT STATEMENT................2 3.2 Network Security Setting..............30... -
Page 4: Fitting For The Indoor Monitor
1.3 Note On Wiring Connection 1. Description Of The Indoor Monitor 1.1 Fitting for the Indoor Monitor The indoor monitor with a separate power supply or an external power supply is optional. please refer to actual control using. If the indoor monitor with a built-in power supply, applicable to wide voltage range(AC 100V~240V). -
Page 5: Installation Process Of Indoor Units
1.5 Wiring Diagram 1.4 Installation Process of Indoor Units For IP 10’’ AHD display series, users can connect up to 2 AHD(720P) outdoor doorbells or 2 IP outdoor cameras, 2 CCTV cameras and three extension CVBS indoor monitors(video door phone) one by one to the corresponding interfaces . -
Page 6: Description On The Indoor Monitor
1.6 Description On The Indoor Monitoring 1.7 Operation Introduction ◆ VISITOR CALL Please be aware of Connection of 2 outdoor cameras is required. Standby mode The Visitor press call button on The Visitor press outdoor camera 2 call button on outdoor camera 1 Monitoring Talk... - Page 7 ◆ ◆ MONITORING CALL TRANSFER TO OTHER EXTENSION Please be aware, Connection of 2 outdoor cameras to 1 indoor monitor is required for dual At least 2 indoor units is required entrance monitoring at least. Outdoor camera call indoor NOTICE: Standby mode monitor and conversation When you are transferring a call to other extension, the original...
-
Page 8: System Settings For Indoor Units
2. System Settings For Indoor Units 2.2 Tool Bar Single-click the right-hand mouse button, and it will display the following toolbar. Note: 1. Users can use a mouse or press buttons on the front panel to operate the device. 2. In standby mode, press the button “ ”... -
Page 9: Channel Status Display
2.3.7 Channel status display The following status icons will appear in the lower left corner of each channel frame. This indicates that the channel has detected motion while in motion-detection mode. By choosing This indicates that the channel is running in normal recording. 2.4 Menu Options Left-click the file to enter the playback menu. -
Page 10: System-Time
[Video Margin] [Camera input]: From this field, select the video input mode that is consistent with CCTV cameras. There are two op tions: HD and D1 resolutions. When the option is “HD”, user must connect Video margin Click “ ” to enter the “Video Margin” menu, AHD(720P) CCTV cameras. -
Page 11: Door Setting-Basic
2.4.2.1 Door Setting-Basic 2.4.3 Network Basic configure includes: “ Call REC ” and “ Do Not Disturb mode ”. Move the cursor to the “Network” icon and left-click to enter the “Network” menu. Network setup includes: “Basic Setup”, “Port” and “Advanced”. Door Setting Network Basic... -
Page 12: Network-Advanced
Wifi Wifi Web Port]: Sets up a Web browser port via HTTP. The default port number is “8090”, but the dlink Password specific number is model-dependent. If Administrator changes the Web port, for example, TP-LINK_169CE6 57/100 123456789 dlink 57/100 “8088”, the port number should be added after the IP address, i.e. http://192.168.15.145:8088 TL-WR941N 42/100 should be entered as the IP address of the Web browser. -
Page 13: Record Scheduling
Sub stream represents the hour from midnight-01:00 AM and the last block (below the “23” on the right hand side of the screen) represents the hour from 11:00 PM-midnight. After setting up the record Channel schedule, click the “ ” button at the bottom of the screen to save it. Frame rate Alternatively, left-click and drag the frames of the boxes in the schedule timeline where you Bit rate... -
Page 14: Maintenance
[Size/Free] : This field indicates amount of space available and the amount of unused space [MD Area] : Sometimes, it is necessary to have some regions in the camera's coverage area available on the SD card. The capacity of the SD can be used up to 128GB. enabled with the motion detection feature, while other regions in the same coverage area do not [Free Time] : Indicates remaining recording time on the SD card. - Page 15 test User Modify PSW Remote Local Login with password Admin Old password New password Confirm password [Local Permission]: This allows the Administrator to give each user its permission to access The following settings can only be set by the system administrator (who will be referred to a unique set of indoor monitor functions.
-
Page 16: Default
2.4.8 Default 3. Web Browser Operation Click “Setup”—“Default”(the tab will be highlighted when selected) and single-click to enter the “Restore to default” menu. 3.1 Feature The system restores the default configuration status in the factory, and corresponding setting can be resumed based on options on the menu. User can select “All” to restore all the settings Install the software through the Internet browser of OS to conveniently operate the network to the original factory settings. -
Page 17: Connection Settings
3.3 Connection Settings is most likely in the same network segment. However, they must not be exactly the same as the ones on the indoor unit, as this will cause IP address conflicts. Taking the preceding figure Remote access to the IP video door phone is carried out over the Internet. In the local area as an example, the IP address should be: 192.168.1.X, where X cannot be 244 or 1 (including network, the IP address of the client-side computer must be in the same network segment that other IP addresses currently being used), and cannot exceed 255, as the subnet mask is... -
Page 18: Operation Interface
[PASSWORD] : The password is as the same as the password for the indoor unit. The default is 888888 [NETWORK] : MAIN STREAM or SUB STREAM. [Open Preview]: “ ” enable to view all the cameras automatically after the login. “ ” means that user needs to connect all the cameras manually after the login. -
Page 19: Toolbar Guide
Using this button, users can download files to their computers and save them to a To search for a recording by date, click calendar in the upper-right corner, and use “ ”and HDD for backup or later viewing. The downloaded file format is “AVI”. The option“ ” on the left “... - Page 20 C. Network Settings From the sidebar on the left, click “Network Setting”, and then select “Network” to enter the network settings interface. The menu allows users to set basic attribute and DDNS setup. G. System Info [Version Information]: From the sidebar on the left, click “System INFO”, and then select “Version INFO”...
-
Page 21: Local Settings
3.5.7 Local Setings From the sidebar on the top, click “Local Setting” to enter the local settings interface. From this page, users can set up the save path for local settings; in the “Record Save Path” field, they can create a save path for recordings, in the “Picture Save Path” field, they can create a save path for video/still images, and in the “File Save Path”... -
Page 22: Appendix 1. Accessing The Indoor Unit Via Mozilla Firefox
5. Select “Allow” to download multiple files and the following screen will appear. Appendix 1. Accessing the indoor unit via Mozilla Firefox First, install Firefox on Windows(This document will use Firefox 3.6 as an example ) After installing Firefox, search for the “IE TAB” add-on for Firefox; this file is named “ie_tab_plus-1.95.20100930-fx+sm (IE Tab Plus (FF 3.6+).xpi”. - Page 23 Menu (MENU/ESC): Press this button to access the toolbar, hide the toolbar, enter or exit from B. To clear the list of Compatibility View sites the menu, and enter or exit sub-menus. Not all website display problems are caused by browser incompatibility. Interrupted Internet Numerical Buttons: Using these buttons, you can choose to display video on your monitor either connections, heavy traffic, or problems with the website can also affect how a page is as a full-screen view of each of the cameras individually (Channels 1 through 2).
Need help?
Do you have a question about the V510 and is the answer not in the manual?
Questions and answers