J-Tech Digital K610 User Manual

Bluetooth: Set the 1/2 switch at the bottom of the mouse to 2, then
3.Macro setting: 4. Hold down the middle button (scroll wheel) and right click 2.Setting
press the Bluetooth button at the bottom of the mouse to make button at the same time for about 3 seconds then release them.
On the drop-down menu select "Assign Macro" to then click
These functions can be customized in the window below
Vertical/upright mouse, with a sleek shape design
1. Dial: Press the middle button of the dial to
the mouse discoverable. When the button is pressed, the The connection should take about 10 seconds to stabilize once
"Macro Manager" to pull up the Macro settings window. Next, click
2 connection modes: 2.4GHz USB transceiver, Bluetooth 4.0
activate the knob functional setting interface
again.
color-changing LED on the side of the mouse will begin toflash.
"NEW" and name the Macro then hit Enter to set the name.
Built-in rechargeable Li-polymer battery
(can only be activated after the driver is
The mouse should now appear as an available device on your
Then click the "Start Record" button under Record Options.
5. If after 10 seconds the connection has not stabilized, repeat
installed). The interface will show up in the
computer, once it is paired to the computer, the LED light will
Once you are done recording the function, click "Stop Record"
steps 1-4 again.
lower right corner, and can be moved with a
stay on.
and click OK to save the Macro. After a Macro is saved, it can be
mouse, by clicking the center of the interface
edited or overwritten at any time.
Plug the USB Nano receiver to a USB port in your computer,
Debugging Tips
The color-changing LED on the side will flash when the DPI setting
and dragging to a new spot. You can select the
after detecting successfully the mouse will begin to function.
is changed. It will flash once when set to the first DPI (800), twice
function by rotating the dial or clicking the
Check to make sure that the transceiver is connected to a USB
4. Other functions:
for the second DPI (1200), three times for the third DPI (1600) and
mouse.
port on your computer
Basic = Cut, Copy, Paste, etc.
four times for the fourth DPI (2400).
Check that the mouse is turned On
2. After choosing the function by rotating the dial, press the middle button of the dial 8 functions are available
or press "Enter" on the keypad to confirm. (If choosing the function with a mouse, no
Advanced: Switch window, close window, etc.
Make sure the mouse and transceiver are within the
Driver Instruction
further action is required). You can reselect the function by pressing the middle
6 functions are available
recommended distance
button again.
Media: Previous track, next track, stop, etc.
1. Installation
Try to reestablish the connection between the mouse and
7 functions are available
transceiver.
You may download the driver for this mouse from our website
You can also adjust the speed of tracking, double-clicking and
www. jtechdigital.com
scrolling.
Note:
After setting the functions, click "Apply" to save all adjustments
Note: The driver is only for adjusting the functions of the mouse,
Pls. download the mouse driver from our official website
the mouse is plug and play, and will still work without the driver.
www.jtdonline.comby searching Model No. V 628M
Connection Instructions
Reestablish the connection between the
(Please make sure the mouse is connected to the computer when
1. When the Nano receiver is plugged into a USB port,
setting the functions in the driver.)
Mouse and Transceiver
your computer will detect the device automatically
2. The mouse will then function when turned on.
If your mouse is not working properly, try to reestablish the
connection between the mouse and transceiver with the
2.4GHz: Set the 1/2 switch at the bottom of the mouse to 1, then
following steps:
connect the transceiver to a USB port on your computer.
1. Take out the Nano transceiver from the computer then reinsert,
The computer should detect the mouse in a matter of seconds
the computer will automatically detect the mouse for about 15
and will then be ready to use. If your computer does not
seconds.
recognize the mouse, you can try to reprogram the mouse.
To program the mouse, hold the left and right click buttons down,
2. Keep the mouse on with the batteries placed properly in the
while switching the mouse on, wait 3 seconds after turning on the
right direction.
mouse to release the buttons.
3. Stay within the recommended distance between the mouse
and receiver (10M)
Mechanical Designer Keyboard
800/1200/1600/2400
3.7V
25mA
6 5 4 3 2
1

Operating Instructions

K610