Summary of Contents for LOGICDATA TOUCHdown LOGIC office
- Page 1 Document Rev1 LOGIC User Manual office Cable Handswitch for installation below the desktop...
-
Page 2: Table Of Contents
Contents Preface ..............................3 General ..............................3 Intended Use ..........................3 Functionality TOUCH ........................3 Package Contents ........................4 Overview ............................4 Mounting Instructions ..........................5 Information regarding the push-push function ................7 Information regarding the user interface panel ................8 Functions .............................. -
Page 3: Preface
LOGICDATA. Note: for definitions and information concerning LOGICDATA control units, please refer to the applicable user manual. Aside of moving your table up and down your LOGICDATA control unit is able to carry out other functions. 2.2 Functionality TOUCH The TOUCH cable handswitch offers the following functionality: ... -
Page 4: Package Contents
Desktop Down Key Memory Position Key 3 Figure 2: Buttons and Display on TOUCH-UD-MDF-4M2-LD Note: this document contains illustrations of the user interface design of the LOGICDATA standard handswitch TOUCH-UD-MDF-4M2-LD. The user interface design can be customized, contact LOGICDATA for further information! -
Page 5: Mounting Instructions
Mounting Instructions Mount the TOUCH cable handswitch underneath your desktop in an appropriate position. The following tools are required for installation: 1 screw driver Note: the handswitch is equipped with a shift mechanism. Mount the handswitch with the user interface panel in the pulled out position to reach all screw holes. 1. - Page 6 Note: Use the following types of screws to fix the TOUCH cable handswitch cylinder-head screws round-head screws pan-head screws Max. diameter of thread: 5mm Max. diameter of head: 10mm Note: if the screws are tightened too much or if the drill holes in the wooden plate and the mounting holes on the handswitch are not aligned correctly, the handswitch gets deformed and the push push function does not work properly.
-
Page 7: Information Regarding The Push-Push Function
3.1 Information regarding the push-push function The TOUCH-UD handswitch is equipped with a push-push function which is used to move out the user interface panel automatically. Note: to extend the control panel you have to press it while it is retracted. Afterwards you have to release it. -
Page 8: Information Regarding The User Interface Panel
3.2 Information regarding the user interface panel The user interface panel is designed to get released from the fixed part in case of too high forces (applied from the top). Figure 8: the user interface panel released from the fixed part in case of too high forces applied to it To mount it again on the sliding mechanism, proceed as follows: 1. -
Page 9: Functions
Functions The TOUCH cable handswitch is capable of a wide range of functions, which are described below. 4.1 Display The TOUCH cable handswitch has a 4 digit display with optional decimal point for position and information display. The current desktop height, error codes and menus can be displayed. The unit (cm or inch) of the displayed height and decimal point settings are depending on the parameters of the control unit. -
Page 10: Advanced Functions
4.3 Advanced Functions 4.3.1 Storing a position You can use this function to adjust the desktop to a saved height. To change to a saved position, proceed as follows: Note: if you are switching on the control unit for the first time, all the saved positions are set to the lowest desktop height (minimum desktop position). -
Page 11: Recalling A Saved Position
4.3.2 Recalling a saved position You can use this function to adjust the desktop to a saved height. To change to a saved position, proceed as follows: Option A (without double click function) Press the required memory position key (e.g. 2) and hold it down. The desktop will move until it reaches the saved position. -
Page 12: Enable And Disable Keylock
4.3.3 Enable and disable keylock The keylock can be enabled and disabled by swiping the screen. After enabling the keylock a key will be shown on the display. Figure 12: The key indicates that the keylock is enabled Figure 13: Activating and deactivating the keylock can be done by swiping left or right underneath the display Note: the direction of movement is not relevant (see Figure 13) Note: you have to swipe the screen gently without pressing a button while swiping. -
Page 13: Appendix
Appendix 5.1 Possible faults and remedies Display does not work (buttons work) Possible cause Remedy Cable is defective Replace the handswitch Display is defective Replace the handswitch Microcontroller is defective Replace the handswitch Handswitch is defective Replace the handswitch Buttons do not work (display works) Possible cause Remedy Cable is defective... -
Page 14: Further Information
Note: this product is REACH compliant according to directive 2006/121/EC (Edict 1907/2006) 6.2 Technical data Note: you can find the technical data of your handswitch in the appropriate datasheet. 6.3 Manufacturer Tel.: +43 (0)3462 5198 0 LOGICDATA Electronic & Software Entwicklungs GmbH Fax: +43 (0)3462 5198 530 Wirtschaftspark 18 Email: office@logicdata.at...