Advertisement
Quick Links
Caution / Note
Please consult with your doctor or a dermatologist before use of this device. Please read all of these instructions
before using the Spot Blaster Pro. If during use your skin starts to feel uncomfortable or you or you become
concerned, stop use immediately and consult your doctor.
Package Contents
Spot Blaster Pro, Standard treatment tip, Ultra-fine needle tips, USB Charging Cable
Charging / Power On
The device should be fully charged before first use. Charge unit
using USB Charging Cable. Power source can be a computer or
AC/DC adaptor.
Indicator lights (1,2,3) will flash green while unit is charging.
When fully charged all three lights will be a constant green.
Approximately 30 minute charging should provide up to five hours
of use.
Unplug charging cable before use. Device will not turn on when
in charging mode.
Turn on/off device by pressing and holding ON/OFF button for
three seconds.
Device will Auto-Power Off after about ten minutes if not in use.
To check the battery level quickly press the ON/OFF button
twice when the device is on: battery level will be indicated by
the three green lights.
Selecting Ion Tip Size & Power Level
1. Standard point tip - for most uses (moles, warts,
granulations, tattoos)
2. Ultra-fine needle - for smaller areas (freckles, sun
spots, blood spots, minor blemishes)
>Standard tip can be screwed into device and finger-
tightened.
>Needle tip needs to be inserted into collar and then
attached to device.
You are advised to clean the tips before and after use
with rubbing alcohol / medical cleaning solution.
Turn on device and select treatment power level by
repeatedly pressing the ON/OFF button. The red
indicator light will show the chosen power level...
1.Low, 2.Medium, 3.High
Start the treatment on the low setting and increase the
power to suit your comfort level.
For Complete Instructions visit www.TommyTimmy.com/Instructions
Spot Blaster Pro Instructions
Assembly
PRECAUTION:
>Keep out of the reach of children and others who don't
know how to use this product.
>Do not over clean the treatment area after using this device
(simple cleaning is OK).
>When the scab area is itchy (new skin growing period), do
not scratch it. The scab will fall off naturally.
>When not in use for extended periods of time, charge it
every 3 to 4 months to ensure battery longevity.
>To avoid injury, do not attempt to take the unit apart for any
reason.
>Do not clean this equipment with water or other liquid.
Advertisement
Summary of Contents for Tommy Timmy Spot Blaster Pro
- Page 1 Please consult with your doctor or a dermatologist before use of this device. Please read all of these instructions before using the Spot Blaster Pro. If during use your skin starts to feel uncomfortable or you or you become concerned, stop use immediately and consult your doctor.
- Page 2 Generally skin tags can be removed common difference is whether it sits After healing period, repeat by the Spot Blaster Pro in one on the upper level of the skin, dermis, treatment so that granulation tissue session. 1) Make sure the standard or has ‘roots’...
Need help?
Do you have a question about the Spot Blaster Pro and is the answer not in the manual?
Questions and answers
my tommy timmy wont burn moles anymore it still lights up but will do nothing when i hold it on my moles please advise
If your Tommy Timmy Spot Blaster Pro lights up but does not burn moles, consider the following possible reasons:
1. Incorrect Operation – Ensure you are holding the device correctly and pressing the OUT button continuously to output the ionic charge. The red power level indicator should turn green when the charge is active.
2. Power Level Too Low – The device has three power levels (Low, Medium, High). Start on Low but increase the power level if needed for effectiveness.
3. Continuous Use Limit – The device stops outputting charge after two minutes of continuous use. If this happens, release the OUT button for five seconds before resuming.
4. Battery Issues – If the battery is low, the device may light up but not function properly. Charge the device every 3 to 4 months to ensure battery longevity.
5. Device Malfunction – If all steps are followed correctly and it still does not work, the device may be defective.
Ensure you are following all instructions properly and consider charging the device or increasing the power level. If issues persist, contact customer support.
This answer is automatically generated