1. Manuals
  2. Brands
  3. Landis Manuals
  4. Finishers
  5. S755 XL (G2)
  6. Operator's manual

Landis S755 XL (G2) Operator's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

S755
/ S755 XL
(G2)
(G2)
FINISHER
Operator Manual
Manufactured by

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the S755 XL (G2) and is the answer not in the manual?

Questions and answers

Summary of Contents for Landis S755 XL (G2)

  • Page 1 S755 / S755 XL (G2) (G2) FINISHER Operator Manual Manufactured by...
  • Page 2 It will deliver efficient, dependable service when used correctly and with care. As with any piece of specialized equipment, for best performance the manufacturer’s instructions must be followed. BEFORE USING THE LANDIS FINISHER, READ OPERATING INSTRUCTIONS MANUAL KEEP GUARDS IN PLACE and in working order.

  • Page 3: Installation

    • CLOSE THE MAIN ACCESS DOOR AND FAN COVER BEFORE OPERATING THE MACHINE. INSTALLATION The S755 / S755 XL Landis Finisher should be located on a flat, firm surface, (G2) (G2) in an area free of obstructions that could interfere with the safe operation of the equipment.

  • Page 4: Electrical Control Box

    No adapter is available or should be used with this tool. If the tool must be reconnected for use on a different type of electric circuit, the reconnection should be made by qualified service personnel; and after reconnection, the tool should comply with all local codes and ordinances. Landis International - 4...

  • Page 5: Lockout Procedures

    Tags must be substantial enough to prevent accidental or inadvertent removal. Both locks and tags are to be standardized by color, shape, or size. Tags should be easily recognized and provide appropriate information about the lockout. Landis International - 5...
  • Page 6 Ensure workers are a safe distance from any potential hazard. The lock and tag should be removed from each energy-isolating device by the worker who applied the lock and tag. Notify affected workers that locks and tags have been removed. Landis International - 6...
  • Page 7 • EYE PROTECTION SHOULD ALWAYS BE WORN BY THE OPERATOR AND OTHERS IN THE WORK AREA WHEN SETTING UP THE MACHINE. EYE PROTECTION IS REQUIRED FOR PROTECTION FROM FLYING DEBRIS AND DUST, WHICH COULD CAUSE EYE INJURY. Before shipment, your Landis Finisher S755 / S755 XL was checked at the...
  • Page 8 4. Start completely the sanding motor. Fine adjust the tracking of the belt at full speed. • AS THE INDIVIDUAL SANDING BELTS WEAR FROM USE, IT WILL BECOME NECESSARY TO MAKE MINOR TRACKING ADJUSTMENTS TO KEEP THE SANDING • BELTS CENTERED. Landis International - 8...

  • Page 9: Sanding Belt Replacement

    • SOME SANDING BELTS ARE CONSTRUCTED TO ROTATE IN ONE DIRECTION ONLY. CHECK ARROW INSIDE SANDING BELT FOR ROTATION. INCORRECT INSTALLATION CAN CAUSE SUDDEN BELT FAILURE RESULTING IN SERIOUS INJURY TO OPERATOR AND OTHERS IN THE WORK AREA. Landis International - 9...
  • Page 10 • DO NOT OPERATE MACHINE WITH ACCESS DOOR OPEN. • NEVER LEAVE MACHINE RUNNING WHILE UNATTENDED. TURN IT OFF. • AS INDIVIDUAL SANDING BELTS WEAR FROM USE, IT WILL BECOME NECESSARY TO MAKE MINOR TRACKING ADJUSTMENTS TO KEEP SANDING BELTS CENTERED. Landis International - 10...
  • Page 11 (SKU: 83102220) and the washer (SKU: SCT). Wear protective gloves to manipulate the cutter. Retain the retaining rod (SKU: TBSHC) and make a rotation towards the bottom to remove the cutter on bayonet. 4. To reassemble, reverse procedures. Landis International - 11...
  • Page 12 Make adjustment to keep a small gap between the shield and the cutter. 3. Adjust the trimmer shield up or down as necessary. Turn knob counter clockwise to raise shield vertically. ✓ Maintenance is important, see our recommendations page 19-21. Landis International - 12...
  • Page 13 : contains tow brushes at left are fixed and two brushes at right (G2) are on bayonet. NAUMKEAG It is possible to adjust the blasting angle using the handles on the right of the motor. Open the naumkeag vent before using this tool. Landis International - 13...
  • Page 14 TO REPLACE THE SAND PAPER 1. Unscrew the nut. 2. Move up the washer and change de sand paper. 3. If necessary, it is possible to change the pad (PN) according to its wear. Repeat the procedure for changing paper. Landis International - 14...
  • Page 15 ✓ Maintenance is important, see our recommendations page 17 & 22. Landis International - 15...
  • Page 16 ACCESSORIES • EYE PROTECTION SHOULD ALWAYS BE WORN BY THE OPERATOR AND OTHERS IN THE WORK AREA WHEN USING THE ACCESSORIES SUPPLIED WITH THE LANDIS FINISHER. EYE PROTECTION IS REQUIRED FOR PROTECTION FROM FLYING DEBRIS AND DUST, WHICH COULD CAUSE EYE INJURY.

  • Page 17: Maintenance

    DUST DRAWER 1. Open the front door if the finisher and turn the 2 handles to open dust drawer. Magnet 2. Empty dust drawer daily. 3. The magnets will keep close the front door. Landis International - 17...
  • Page 18 Clean the rubber/felt surface to avoid accumulation of dust. If there is too much accumulation, the sanding belt won’t stay on the rubber/felt wheel and you will have problems with tracking. IDLER WHEEL Clean the flat surface to avoid accumulation of dust with a scraper. Landis International - 18...
  • Page 19 Check its condition. If it is cracked, replace it. • MOTOR REPLACEMENT REQUIRES WORKING WITH 220 VOLTS ELECTRICAL WIRING AND CAN BE HAZARDOUS. PLEASE CALL A QUALIFIED ELECTRICIAN OR A LANDIS TECHNICIAN. MOTOR Clean each side of the motor and the wheels with a vacuum cleaner or an air jet.
  • Page 20 • DO NOT OPERATE MACHINE WITH SANDER HOUSING DOORS OPEN. • AFTER MAKING ADJUSTMENTS, REMOVE ALL WRENCHES AND OTHER TOOLS BEFORE OPERATING THE SANDER. • USE EXTRA CAUTION WHEN STARTING THE FINISHER FOR THE FIRST TIME AFTER INSTALLING A NEW TOOL OR PART. Landis International - 20...

  • Page 21: Monthly Maintenance

    3. Check the tension of the V-belt running to the motor; it should depress approximately 12 mm (½”) when pressed in the middle with moderate force. 4. Rotate the V-belt by hand, visually inspecting the belt for damage. Landis International - 21...
  • Page 22 4. Remove the velcro strap (888443LG) from the blower entry. 5. You can use a vacuum cleaner to clean both inside and outside of the dust bag. 6. 2 solutions for cleaning the bag: Dry cleaning Cold water and drying flat Landis International - 22...
  • Page 23 10. Change back filters only if they are defiled (SKU: G8PM300399). LUBRICATION Your S755 / S755 XL Landis Finisher is equipped with sealed bearings (G2) (G2) throughout, which should be replaced if they ever wear out. Other parts should not require any lubrication, only cleaning the parts is required.

  • Page 24: Troubleshooting

    If there is still a problem, contact our customer service at 1 800 634-0806. V-BELT ADJUSTMENT AND REMOVAL All V-Belts on the S755 / S755 XL Landis Finisher should be (G2) (G2) checked monthly for proper tension and general condition. Loose V-Belts will decrease the power available to the various tools and lower the efficiency of your Finisher.
  • Page 25 4. Loosen set screw on Naumkeag shaft and pull out the adapter from the shaft motor. 5. Reassemble with new motor in reverse order to above procedures. If there is still a problem, with the shaft, bearing, idler wheel, motor, electricity, contact our customer service at 1 800 634-0806. Landis International - 25...
  • Page 26 Belt worn out or frayed one side. Install new belt. MOTOR STOPS WITH SWITCH ON CAUTION! Turn switch off immediately Too much equipment operated on same circuit on which Landis S755 (G2) S755 XL Finisher is connected. Check circuit breaker or fuse box.
  • Page 27 Operator Manual S755 (G2) / S755 XL (G2) October 2017 LANDIS S755 / S755 XL - SOLE TRIMMER (G2) (G2) Landis International - 27...
  • Page 28 Operator Manual S755 (G2) / S755 XL (G2) October 2017 LANDIS S755 / S755 XL - HEEL TRIMMER (G2) (G2) Landis International - 28...

This manual is also suitable for:

S755 (g2)

Table of Contents