Summary of Contents for Elexa Consumer Products Guardian Bridge GBR1
- Page 1 BRIDGE User Manual Model Name: Bridge Model#: GBR1 Elexa Consumer Products 2275 Half Day Road, Ste#160 Bannockburn, IL 60015...
-
Page 2: Table Of Contents
Contents 1 Overview 1.1 Key Features ..........1.2 Communication . -
Page 3: Overview
Overview The Guardian Bridge is a device that can communicate to a single valve controller over Guardian RF and to a security panel over wire, or a Z-Wave hub. This allows a security panel or Z-Wave hub to open/close the valve controller and be alerted if a leak is detected. Key Features •... -
Page 4: Specifications
Specifications This section describes the requirements and scope of the Guardian Bridge Environmental Specifications Feature Description Operating Temperature Range 0°C to 70 °C Operating Humidity Range 5% to 90% RH Non Condensing Storage Temperature Range -40°C to 75 °C - capable of opera- tion after a 20 minute transition from storage to operating tem- perature... -
Page 5: Tooling
Item Description and Specifications Type Plastic Resin Blue:3005U; Finish Same as valve controller 2.4.1 Tooling Tooling shall be good for over 300,000 injections. 2.4.2 Fit and Finish • Flash allowance shall not to exceed 0.13 mm (0.005in). Flash applies to parting lines, ejector pins, ejector blades and ejection sleeves •... -
Page 6: Button
Button The single button will on the back will be used to pair the Bridge with a valve controller or a Z-Wave hub. A single press will be used to pair the Bridge to a valve controller (like shaking the leak detector). A triple press (3 presses in under 2 seconds) will put the bridge in Z-Wave inclusion mode if it has not been included yet, or in exclusion mode if it is currently included. -
Page 7: Z-Wave Inclusion
• A Leak Sensor • A temperature sensor (see §4.4.1) Z-Wave Inclusion The Bridge will enter inclusion mode when first powered on (if not already included in a Z-Wave network) and will stay in inclusion mode for 30 seconds. After 30 seconds, if the Bridge is not included, pressing the button on the device 3 times in less than 2 seconds will put it back in inclusion mode for 30 seconds. -
Page 8: Compatible Command Classes
4.4.2 Compatible Command Classes Command Class Notes COMMAND CLASS VERSION V2 Returned Value: 03 04 3D 01 01 01 00 (86) Z-Wave Library Type: 03 (Enhanced Slave) Protocol Version: 04 3D Protocol Sub-Version: 01 01 Application Version: 01 Application Sub-Version: 00 COMMAND CLASS BASIC V1 (20) COMMAND CLASS SWITCH BI- Binary Switch commands will open/close the valve. -
Page 9: Relaylink
COMMAND CLASS NOTIFICATION The Guardian Bridge sends a notification report to associ- V8 (71) ation group 1 when any Leak Detector in the system senses moisture. Returned Value: 00 00 00 FF 05 XX 00 00 V1 Alarm Type 00 (Unsupported) V1 Alarm Level 00 (Unsupported) Notification Status: FF (Unsolicited Reporting is Enabled) Notification Type: 05 (Water Alarm) -
Page 10: Pad Printing
STATEMENT OF WARRANTY : 1 Year Limited Warranty Elexa Consumer Products will not honor the warranty if the product is purchased through an unauthorized seller. Elexa Consumer Products, Inc. (”ECP”) warrants to the original retail purchaser (”Purchaser”) that the Bridge (the “Product”) will be free of defects in materials or workmanship under use for one (1) year from the date of purchase (the... - Page 11 Bridge FCC and IC Statement Bridge is used to connect Guardian Valve Controller to Z-wave network. Bridge is also used to control Valve Controller open/close. The Guardian RF(915Mhz) is used for the communication between Bridge and Valve Controller. The Z-wave (908.40Mhz and 916Mhz) is used for the communication between Bridge and other Z-wave Devices. These 2 frequency are switched automatically.
Need help?
Do you have a question about the Guardian Bridge GBR1 and is the answer not in the manual?
Questions and answers