Advertisement
in the bottom position, MIC 1 and MIC 2 and talkover are off. When
the MIC/TALKOVER SWITCH (7) is in the center position MIC 1 and
MIC 2 are on, the MIC INDICATOR (6) will glow, but talkover is off.
When the MIC/TALKOVER SWITCH (7) is in the top position, MIC 1
and MIC 2 and talkover will be on and the volume of all sources
except the Mic inputs are lowered by 16 dB. The TREBLE (2) and
BASS (3) controls allow you to fully adjust the tone of MIC 1 and MIC
2. MIC 1 LEVEL (5) controls the level of MIC 1. The MIC 2 LEVEL
(4) controls the level of MIC 2.
10. CUE SECTION: By connecting a set of headphones to the
HEADPHONE (35) jack, you can monitor any or all of the channels.
Press the CUE ASSIGN (20) buttons for channels 1 - 4 to select the
channel or channels to be monitored and their respective LED
indicators will glow. Use the CUE LEVEL (34) control to adjust the
cue volume without effecting the overall mix. By moving the CUE
PGM PAN (33) control to the left you will be able to monitor the
assigned cue signal. Moving the control to the right will monitor the
PGM (program) output. Moving to the right will monitor the PGM
(program) output.
11. DISPLAY: The DISPLAY (21) indicates the MASTER output left and
right levels.
12. SOUND EFFECTS SECTION: Six different sound effects (UFO, TRON
BLAST, SIREN, GAS, MACHINE GUN and EMERGENCY) may be
added to your mix by depressing the SOUND EFFECTS CONTROL
BUTTONS (25). The volume of the effects can be adjusted using the
EFFECTS LEVEL CONTROL (27). The pitch of the effects can be
increased or decreased using the EFFECTS SPEED CONTROL (26).
Specifications
INPUTS:
DJ Mic....................................................1.5mV 2Kohm balanced
Phono.........................................................................3mV 47Kohm
Line.......................................................................150 mV 27Kohm
OUTPUTS:
Amp/Booth......................................................0 dB 1V 400ohm
Max..............................20V
Rec...........................................................................225mV 5Kohm
MIC 1 & MIC 2:
DJ Mic....................................................1.5mV 2Kohm balanced
Bass......................................................................................± 12dB
High.......................................................................................± 12dB
GENERAL:
Frequency Response....................................20Hz - 20KHz +/- 2dB
Distortion................................................................................0.02%
S/N Ratio...............................................................better than 80dB
Talkover Attenuation..............................................................-16dB
Headphone Impedance.........................................................16ohm
Power Source.............................................115/230V 50/60Hz 10W
Dimensions................................................19"w x 4"h x 9"d
Weight........................................................................10.17 lbs
Item #
Peak
to
Peak
Item #
Page 5
Parts Lists
Cabinet Parts and Packing
Description
1
PANEL CONTROL
2
PANEL REAR
4
COVER BOTTOM
5
BRACKET VR
6
HOLDER X-FADER
7
PROTECTOR PLATE FOR 115/230V SWITCH
8
SOUND CONTROL KEY
9
SWING LEVEL
10
KNOB PUSH (SMALL)
11
BUSHING FOR KNOB (SMALL)
12
KNOB SLIDE (BIG)
13
KNOB SLIDE
14
KNOB ROTARY (ASSIGN)
15
KNOB ROTARY (B)
16
KNOB INLAY (BLACK)
17
KNOB INLAY (GRAY)
18
EQ VR INLAY
19
TRIM VR
20
INLAY PLATE
21
HOLDER LED 3f LED(17mm)
22
HOLDER LED
23
HOLDER LED
24
WASHER XLR
25
PCB SPACER SUPPORT
26
PAD FOOT
27
BNC DUST PROOF CLOTH
28
DUST PROOF CLOTH (KNOB-SWING)
29
DUST PROOF CLOTH (VR)
30
FADER DUST PROOF CLOTH
31
GND SCREW
32
PAN-HEAD MACHINE SCREW; PMS 2X4(B)
33
FLAT-HEAD MACHINE SCREW; FMS 2X4 (Y)
34
PAN-HEAD MACHINE SCREW; PMS 2.6X4(B)
35
BAND-HEAD MACHINE SCREW; BMS 3X2X4
36
BAND-HEAD TAPPING SCREW/TWIN SCREW;
BTS-2 3X8(AB) TWIN
37
FLAT-HEAD TAPPING SCREW; FTS-3 3X6(AB)
38
BAND-HEAD TAPPING SCREW; BTS-3 3X10(AB)
39
BAND-HEAD TAPPING SCREW; BTS-3 3X6(AB)
40
FLAT-HEAD TAPPING SCREW; FTS-3 3X12(AB)
41
FLAT-HEAD TAPPING SCREW; FTS-3 3X12(Y)
42
BAND-HEAD TAPPING SCREW; BTS-3 3X5(AB)
43
BAND-HEAD TAPPING SCREW/TW-E;
BTS-3/TW-E 3X6(AB)
44
NUT/WASHER 3mm
Printed Circuit Boards
Description
PRINTED CIRCUIT BOARD PDM-24S-1:
1
IN/OUT
PRINTED CIRCUIT BOARD PDM-24S-2:
2
MAIN
PRINTED CIRCUIT BOARD PDM-18-3:
3
EFFECT
PRINTED CIRCUIT BOARD PDM-24S-4:
4
FADER
PRINTED CIRCUIT BOARD PDM-18-5:
5
PHONES
PRINTED CIRCUIT BOARD PDM-18-6
6
Part #
002-210
034-001
032-018
021-763
022-322
022-305
049-199
023-674
002-531
002-532
002-704
002-715
003-102
003-110
148-236
148-239
003-994
003-970
003-373
003-969
003-986
003-975
003-564
047-474
049-206
159-201
156-216
159-171
159-196
146-710
102-007
101-008
102-025
107-015
110-172A
111-043A
111-044A
111-046A
111-049A
111-050
111-051A
111-053A
131-081
Part #
262-044
262-045
262-047
262-046
262-048
262-049
Advertisement
