Table of Contents
Advertisement
Advertisement
Table of Contents
Summary of Contents for Safire SF-TESTER-ARM-5N1-4K
- Page 1 SF-TESTER-ARM-5N1-4K INSTRUCTION MANUAL...
- Page 2 Thank you for purchasing the IP camera tester. Please read the manual before using the IP camera tester and use properly. For using the IP camera tester safely, please first read the「Safety Information」 carefully in the manual. The manual should be kept well in case of reference. Keep the S/N label for after-sale service within warranty period.
-
Page 3: Table Of Contents
CCTV TESTER User Manual Content 1 .Safety information............................1 2. IP Camera Tester Introduction........................2 2.1 General..............................2 3. Operation...............................2 3.1 Installing the Battery..........................2 4. IP Camera Testing............................3 4.1 Power Camera............................ 3 4.2 IP discovery............................3 4.3 Rapid ONVIF test..........................4 4.4 Non-Onvif IP camera test........................9 5. -
Page 4: Safety Information
CCTV TESTER User Manual 1 .Safety information ◆ The tester is intended to use in compliance with the local rules of the electrical usage and avoid to apply at the places which are inapplicable for the use of electrics such as hospital, gas station etc. ◆... -
Page 5: Ip Camera Tester Introduction
CCTV TESTER User Manual 2. IP Camera Tester Introduction 2.1 General The IPS touch screen IP camera monitor is designed for maintenance and installation of IP cameras, analog cameras, TVI, CVI, AHD cameras, as well as testing 4K H.264 /4K H.265 camera by mainstream, The tester enables it to display network HD cameras and analog cameras in high resolution. -
Page 6: Ip Camera Testing
CCTV TESTER User Manual 4. IP Camera Testing 4.1 Power Camera Camera can be powered from the DC 12V/3A output or by Power over Ethernet. 4.2 IP discovery Press IP discovery , tester auto-scan the whole network segment IP, as well as auto-modify the tester’s IP to the same network segment with the scanned camera's IP. -
Page 7: Rapid Onvif Test
CCTV TESTER User Manual Local IP: Tester’s IP address, Tester can auto-modify the tester’s IP to the same network segment with the scanned camera's IP. Discovery IP: Connected tester equipment’s IP address. If the camera connected to the tester directly, tester will display the camera’s IP address, if tester connects to Local Area Network, it displays the current IP address. - Page 8 CCTV TESTER User Manual Across network segments scan: After open this function , Rapid ONVIF function can across network segments to scan camera’s IP. Auto Login: After open this function, tester can auto login camera and display camera image (The login password is the same with last time, the first time using password is the default password "admin") Video transmission protocol: UTP and TCP protocol.
- Page 9 CCTV TESTER User Manual While in the “Live video” menu, click “Video Menu” at the top right of the image to access the following tools: Snapshot, Record, Photo, Playback, Lens simulation, PTZ and Settings. Network setting: Click “Network Set” to change the IP address. Some cameras cannot support change IP address, so there is no change after saving.
- Page 10 CCTV TESTER User Manual OSD Menu: Select OSD and popup the OSD menu. include time, channel name and other optional items. After channel selecting, you can edit the channel name, modify the display position, and switch the font size. Select “default location” in “content location” is without modification.
- Page 11 CCTV TESTER User Manual Set preset position: Move the camera to preset position, enter the preset number on the Bottom right corner to complete position preset. Call the preset position: Select the preset number on the left, click "Call" to call preset.
-
Page 12: Non-Onvif Ip Camera Test
CCTV TESTER User Manual Click doc menu again, you can preview the report document. Icons description: the description of function icons on the bottom toolbar 4.4 Non-Onvif IP camera test Display image from the 4K H.265 camera by mainstream. Note: Currently, the IPC Test App only supports some brands’ specific IP cameras, these include specific models made by ACTI, AXIS, Dahua, Hikvision, Samsung, and many more. - Page 13 CCTV TESTER User Manual Local IP: This is the tester’s IP address. Click “Edit” to enter “IP setting” and change the tester’s IP address settings. IP camera type: Click on the IP Camera type to select the Manufacturer and model number of the integrated IP camera.
-
Page 14: Analog & Hd Camera Testing
CCTV TESTER User Manual 5. Analog & HD Camera Testing 5.1 Analog camera test Analog camera test and PTZ control. Select relative function on the right side Toolbar to operate , functions including “Photos”, “Snapshot”, “Record”, “Playback”, “PTZ”, “Set”. Double-taps on the screen to make the image displayed full screen. Check and set the protocols, address, interface and baud, all must be consistent with the dome camera, then the IPC tester can test .After setting the parameter, the tester can control the PTZ and lens. - Page 15 CCTV TESTER User Manual The PTZ address in the tester must be consistent with the dome camera or decoder, then the IPC tester can test. After setting the parameter, the tester can control the PTZ and lens. Set preset position: Move the PTZ camera to the preset position, the Tap it and input preset position number.
- Page 16 CCTV TESTER User Manual 1.2 RS485 control （2）Coaxial camera menu setting Input calling dome camera menu address code, you can press the key “Enter” or click the icon to call the dome camera menu.
-
Page 17: Tvi Camera Test
CCTV TESTER User Manual set the parameters by 5.3 TVI camera test When HD TVI signal input, the tester will display the image resolution on the top bar. Double-taps on the screen to make the image displayed full screen. The tester supports resolution support up to 3840 x 2160P 12.5/15 FPS. Coaxial camera menu settings: Tap icon “UTC”, select “menu setting”... -
Page 18: Ahd Camera Test
CCTV TESTER User Manual 5.4 AHD camera test When AHD signal input, the tester will display the image resolution on the top bar. Double-taps on the screen to make the image displayed full screen. The tester supports resolution support up to 3840 x 2160P 15 FPS. (1) Coaxial PTZ control UTC control: select “PTZ control or PTZ control-2”... -
Page 19: Other Function
CCTV TESTER User Manual 6. Other function 6.1 TesterPlay The meter creates WIFI hotspot, connect mobile phone to the tester’s WIFI hotspot, or the tester and mobile phone connect to the same Wi-fi network. Select “TesterPlay” app to enter, click “Start” button to generates two-dimensional code, download and install the VLC client software, you can view the screen real-time projection. -
Page 20: Network Tool
CCTV TESTER User Manual 6.2 Network tool (1) IP address scan Connect the cable to the LAN port, click icon to enter, Set your IP address search range by changing the Start and End IP addresses. Click the “Start” button to scan the IP address range. -
Page 21: Rj45 Cable Tdr Test
CCTV TESTER User Manual (5) DHCP server Click on the DHCP icon to open the DHCP server app. Select the “Start” check box at the top and make any desired changes to the network settings. Click “Save” to start assigning dynamic IP addresses for IP cameras and other networked devices. Click the “Refresh”... - Page 22 CCTV TESTER User Manual Single test: Test cable status, length and attenuation. Repeat test: Continue to test cable status, length and attenuation. Status: After link up, screen display “online”, if not link up or open circuit, screen display “open circuit”, if cable pair is short circuit, screen display “short circuit”. Length: The max test length is 180 meters, when cable is open circuit or short circuit, can test the cable length, if screen display “online”, the testing result would be not accurate.
-
Page 23: Poe Power / Dc12V 3A Power Output
CCTV TESTER User Manual 6.4 PoE power / DC12V 3A power output When the tester is turned on, the DC12V power output functions are automatically turned on. To use the PoE Power Output function,change the switch “ON” or “OFF”. The IP camera needs to be connected to the LAN port before you turn PoE Power on. If the IP camera Supports PoE, the PoE power is delivered via pins 1, 2, 3, and 6 on the LAN port. -
Page 24: Update
CCTV TESTER User Manual 6.5 Update Copy the downloaded update file to SD card "update" directory, if no directory, please create one. Click the icon to open the Update menu. Select “Local Update” to update via the SD card or select “Online Update” to check for updates on the internet. If there are applications that need updating, the applications will be listed in the interface, click related applications, update to the latest version. - Page 25 CCTV TESTER User Manual Browse It includes Music, Videos, Pictures, Documents, zip file etc. It is convenient to view and manager. FTP server You can choose internal or external SD card. Other operation details, Pls refer to FTP settings.
-
Page 26: System Setting
CCTV TESTER User Manual 6.7 System Setting Language: Select your desired language: English, Chinese, Korean, Russian, Italian, Polish, Spanish, French or Japanese. Typewriting: You can select typewriting or install other typewriting: Date/Time: Set the Date/time of the IP tester. IP setting: Manually set the IP address, Subnet Mask, Default Gateway and DNS address or select “Dynamic allocation”... - Page 27 CCTV TESTER User Manual segments, click “Advanced” and then click “Add” to enter another IP address for the IP tester. WLAN Net: Turn WiFi off or on by pressing the “Open the wifi” button. Once WiFi is turned on, and click connected WIFI, it will scan for wireless networks in your area. Select and press “WIFI”...
- Page 28 CCTV TESTER User Manual Start the FTP server and then input the tester’s FTP address in the PC’s address bar. This will enable the PC to read, copy and edit the files from the SD card without the use of SD card reader. Version information: Shows applications version information, if press any apps icon several seconds to uninstall.
-
Page 29: Tools And Apps
CCTV TESTER User Manual pattern Lock screen or “NO”. Restore the factory settings: If the tester to restore factory settings, all your personal files and apps will be removed. Power Off: Manully to set the power off after hibernation time(0-23h 59min). 6.8.Tools and Apps... -
Page 30: Specifications
CCTV TESTER User Manual 7. Specifications 7.1 General Specifications Model IP Camera Tester Display IPS touch screen cctv tester Network port 10/100/1000M auto adjust, RJ45 WIFI Built in WIFI, speeds150M, display wireless camera image H.265 Main New hardware decoding, 4K H.265/H.264 camera image stream test display by mainstream testing IP discovery... - Page 31 CCTV TESTER User Manual 2560x1440P 15,25,30fps/ 2688x1520p 15fps, 2592x1944P 12.5,20fps/3840 x 2160 12.5/15 fps 1 channel AHD input （ BNC interface), resolution support 720P 25,30fps / 1080p 25,30fps/2048x1536P 18,25,30fps, AHD video signal 2560x1440P 15,25,30fps/ 2592x1944P 12.5,20fps, 3840 x test 2160P 15 fps, UTC control and call OSD menu Analog video test 1 channel BNC Input, NTSC/PAL (Auto adapt) Snapshot, Video...
- Page 32 CCTV TESTER User Manual Parameter OSD menu, select your desired language: English, Chinese, Operation setting Korean, Russian, Italian, French, Polish, Spanish, Japanese etc Auto off 1-30 (mins) General Working -10℃---+50℃ Temperature Working 30%-90% Humidity The data above is only for reference and any change of them will not be informed in advance.