1. Manuals
  2. Brands
  3. Remo+ Manuals
  4. Accessories
  5. RemoBell W
  6. Quick start manual

Remo+ RemoBell W Quick Start Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
RemoBell® W
Quick Start Guide

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the RemoBell W and is the answer not in the manual?

Questions and answers

Related Manuals for Remo+ RemoBell W

Summary of Contents for Remo+ RemoBell W

  • Page 1 RemoBell® W Quick Start Guide...

  • Page 2: What's In The Box

    WHAT’S IN THE BOX REMOBELL® W BRACKET POWER KIT SECURITY BALL END MOUNTING SCREW HEX L KEY SCREWS AND ANCHORS 15° ANGLE 5° WEDGE EXTENSION WIRES MOUNT MOUNT AND WIRE NUTS * For brick or stucco surfaces, you’ll need a drill and drill bit.
  • Page 3 MEET REMOBELL® W FRONT* BACK Camera lens Reset button Power terminal ALS sensor PIR sensor BRACKET IR LED Mounting holes Bell button Power terminal Speaker Reset hole Security screw hole * Remove the scratch protection sticker before use...

  • Page 4: Before You Begin

    • If you have an electronic chime, please refer to its manual for instructions. WARNING: Before installing your RemoBell W, please con rm the type of chime system in your home (Mechanical or Electronic). If the improper chime type is selected it may cause the doorbell to malfunction, resulting in device failure or re.
  • Page 5 POWER KIT INSTALLATION 1. Remove the cover of your mechanical chime. 2. Take a picture of the wiring for reference during installation. 3. Loosen the screws and remove the wires. 4. Straighten the wires that were just removed. Then insert the two wires to the connector on the provided power kit in any order.
  • Page 6 5. Connect the Power Kit wires to the chime terminals in any order and tighten the screws. 6. Place your Power Kit so that it doesn't interfere with moving parts or mu e the chime. You can use the adhesive backing to hold it in place. 7.
  • Page 7 DOORBELL MOUNTING 1. Remove your existing doorbell and disconnect the wires. 2. Based on your doorbell location, adjust the camera’s viewing angle by choosing the appropriate Mount type. 3. If you use the Angle Mount or the Wedge Mount, follow Option A. If you are only using the 15°...
  • Page 8 4-3. Connect the existing wires to the Power Terminal on the back of the Bracket. (Optional) If the existing wires are short, use extension wires and wire nuts to extend the wires. Insert an exposed end of the extension wire and one chime wire into the Wire Nut, and twist it tightly.
  • Page 9 Option B 4-1. Connect the existing wires to the Power Terminal on the back of the Bracket. 4-2. Place the Bracket onto the wall and mark the screw placement in the mounting holes. * For hard surfaces like brick and stucco, use a drill and 5mm drill bit to make holes.
  • Page 10 5. Once secured the Bracket, slide the RemoBell® W from the top of the Bracket, then rmly push the device in. 6. Tighten the Security Screw into the Security Screw Hole to secure the device to the Bracket. 7. Now go and restore power on the breaker box. If the LED light is ashing up and down, then proceed to DOORBELL SETUP (Page 11).
  • Page 11 DOORBELL SETUP CREATE AN ACCOUNT 1. Make sure your mobile device is connected to your home’s 2.4GHz Wi-Fi. (5GHz not supported) 2. Download and launch the RemoPlus app. 3. Press "Sign Up" at the bottom of the login page. 4. Enter your email and create a password. Then press "Sign Up".
  • Page 12 RemoBellW_xxxxxx network, switch back to the RemoPlus app and press "Continue". If you can not connect with your RemoBell W Wi-Fi, make sure you connect to your home Wi-Fi and retry the setup process by logging into your account and pressing "Add Device".
  • Page 13 Forgot your password? 1. Press "Forgot Password" on the login page. 2. Enter your account email and click SEND. 3. Check your email (including spam folder) for the temporary password. 4. Open the RemoPlus app and log in using your account email and the temporary password.

  • Page 14: Troubleshooting

    TROUBLESHOOTING Can’t see the videos on your Recent Activity? For Android users, allow all permissions to the RemoPlus app: Settings > Applications Manager > Permissions > Storage Check your Settings Motion Sensor in the RemoPlus app: Save Videos to Cloud Menu >...

  • Page 15: Electrical Shock Warning

    ELECTRICAL SHOCK WARNING: DO TURN OFF POWER on the breaker box before RemoBell® W installation. Serious electrical shock, injury, or death may occur if left on. DO NOT TURN ON POWER until RemoBell® W installation is complete. Contact a licensed electrician if you need any assistance with power or wiring.

  • Page 16: Fcc Compliance Statement

    FCC COMPLIANCE STATEMENT You are cautioned that changes or modi cations not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device.

Table of Contents