Do you have a question about the 2019 Smartwatch and is the answer not in the manual?
Questions and answers
Jake
March 9, 2025
How the hell do update time for daylight saving ?
1 comments:
Mr. Anderson
March 9, 2025
The time on the Spade & Co 2019 Smartwatch syncs automatically with your smartphone when connected via the Da Fit app. To update the time for daylight saving, ensure your smartphone's time is correct and that the smartwatch is connected to the Da Fit app. The time will update automatically.
This answer is automatically generated
Richard Provencher Jr
May 29, 2025
my smart watch will not charge; it is down to 6 percent but just goes between main screen and percent of charge. I have had the charge cord on overnight and no rise, still flashes 6 %. What do I do? I have had my smart watch for about two years now.
1 comments:
Mr. Anderson
May 29, 2025
If your Spade & Co 2019 Smartwatch will not charge and remains at 6 percent, do the following:
1. Make sure the charger is connected to a USB or power outlet. 2. Check that the charger is positioned correctly, with the two connectors aligned with the watch connectors on the back. 3. Ensure the charger pins are properly placed. 4. Look for the charging animation on the watch screen to confirm it is charging.
If the issue continues, try a different USB port or charging adaptor.
This answer is automatically generated
Floyd Dickman
April 8, 2025
How to sync smartwatch 3 with my andrroid phone?
1 comments:
Mr. Anderson
April 9, 2025
To sync the Spade & Co 2019 Smartwatch with an Android phone:
1. Fully charge the watch. 2. Install the Da Fit app on your Android phone. 3. Open your phone’s Bluetooth settings and select your watch. If it's already paired, choose “forget this device.” 4. Kill the Da Fit app or reboot your phone. 5. Relaunch the Da Fit app. 6. Tap the watch icon and select “Connect Device.” 7. Follow the on-screen instructions under "Getting Started."
This answer is automatically generated
Gayle Momserrate
April 4, 2025
Need to turn off alarm
T
1 comments:
Richard Provencher Jr
May 29, 2025
@Gayle Momserrate Says UK/CA
Gayle
April 4, 2025
Need to turn off alarm
1 comments:
Mr. Anderson
April 4, 2025
To turn off the alarm on the Spade & Co 2019 Smartwatch, open the Da Fit app on your smartphone, tap on the watch icon, select Alarms, then tap on the alarm you want to turn off and adjust or delete it.
This answer is automatically generated
Patty
March 20, 2025
1) I enabled red dot for my notifications. Has never shown on the face of the watch. 2) My watch vibrates when I get a text but not consistently. 3) Have to go into the app, tap on notifications and disable most of the social media apps that are turned on. Clicked on SAVE, yet the very next day, the apps are turned back on.
1 comments:
Mr. Anderson
March 20, 2025
To manage notifications on your Spade & Co 2019 Smartwatch, open the Da Fit app on your smartphone, tap on the watch icon, and select Notifications. From there, you can turn notifications on or off for specific apps. If you experience inconsistent vibration for texts, ensure notifications are enabled for messaging apps in the Da Fit app. If social media app settings persist, toggle the notification settings off and on again in the Da Fit app to refresh them.
This answer is automatically generated
Brenda Jordy
March 9, 2025
I’m trying to get my watch to change to daylight savings time but I can’t get the app to find my watch. I have turned off my phone, turned off and back on Bluetooth, deleted the da fit app, reinstalled it, numerous times, still will not connect! This is ridiculous!! Help!
1 comments:
Mr. Anderson
March 9, 2025
To connect your Spade & Co 2019 Smartwatch to the Da Fit app, follow these steps:
1. Ensure Bluetooth is turned on on your smartphone. 2. Install and open the Da Fit app on your smartphone. 3. Tap on the watch icon and select your smartwatch (typically "SN60-Plus") to connect it. 4. Once connected, the time on your smartwatch will automatically sync with your phone.
To adjust for daylight savings time, ensure your smartphone's time settings are updated, as the smartwatch syncs time from the phone.
This answer is automatically generated
Cheryl L Castille
March 3, 2025
The Smart watch I purchased on Dec. 30, 2023 was beeping the whole time I charged it recently. After it was charged it was not connected to my phone. I reset the watch and connected it to my phone. It was working well. I just tried turning it on and all I get is a lighted blank screen.
1 comments:
Mr. Anderson
March 3, 2025
If your Spade & Co 2019 Smartwatch has a blank screen after charging, long press the home button at the bottom of the screen for a few seconds. If the screen does not turn on, ensure the watch is properly charged using the provided USB charger. If the issue persists, email support@spadeandco.com for further assistance.
This answer is automatically generated
Lisa Harden
January 22, 2025
My watch is dead and won’t charge
1 comments:
Mr. Anderson
February 10, 2025
If your Spade & Co 2019 Smartwatch won't charge, it might be due to the following reasons:
1. The watch could be out of power. 2. The USB charger provided might not be properly connected or functional.
Make sure to use the USB charger that came with the watch and ensure it's securely connected. If the issue persists, refer to other troubleshooting steps or contact support.
This answer is automatically generated
Maggie Garrison
July 27, 2025
How do you delete messages? When I do select delete, it doesn’t delete
Summary of Contents for Spade & Co 2019 Smartwatch
Contents Contents Getting Started Install the Da Fit app on your smartphone Connect your smartwatch to your smartphone Turn OFF your watch Turn ON your watch Charge your watch Reset your watch How to Navigate Settings Language Time Formats (12-hour or 24-hour) Unit Format (feet or meters) Temperatures (Fahrenheit or Celsius) Screen Brightness...
Page 3
Watch lost connection with the Da Fit app Battery lasts for less than a day Watch is not charging Unable to pair with phone Watch does not turn ON Slow touch response Inaccurate measurement Screen not bright enough Not consistently receiving text and call notifications Da Fit app shows too many ads...
Getting Started Install the Da Fit app on your smartphone s padeandco.com/app to download the Da Fit On your Android smartphone or iPhone, visit app. You will need this app to sync data with your smartwatch. Connect your smartwatch to your smartphone Make sure Bluetooth is turned on on your smartphone.
Charge your watch Wrap the charging adaptor around your watch as shown on the left picture. Plug the USB port into a computer or your smartphone outlet adaptor. Note : Make sure the pins on the charger are properly placed. You should see the charging animation when the watch is charging correctly.
How to Navigate In order to navigate the menu on your watch, simply tap on the front facing bottom located at the bottom of the screen. A small tap takes you to the next menu item. A long tap takes you inside this menu item. For example, a long tap on the messages menu will show you your text messages.
Settings Language To change the language, open the Da Fit app on your smartphone, tap on the w atch icon , select O thers , then L anguage . You can select among English, Chinese, French, Spanish, Italian, Portuguese and others. Time Formats (12-hour or 24-hour) To display the time in either 12-hour or 24-hour format, open the Da Fit app on your smartphone, tap on the ...
Watch Faces You can choose among a digital watch face (by default), an analog watch face or a custom watch face with your own photo. To change your watch face, open the Da Fit app on your smartphone, tap on the w atch icon and select W atch Faces . Simply select the watch face you want and your watch face will automatically update.
Alarms You can set up to top 3 alarms on your watch. To set an alarm, open the Da Fit app on your smartphone, tap on the w atch icon and select A larms . Tap on any alarm to change the time, then ...
Track your Sleep In order to track your sleep, simply wear your watch at night. Your sleep data will show on your watch as well as on your Da Fit app on your smartphone. Note : the sleep tracking is only enabled during the night.
Track your Heart Rate In order to track your heart rate, l ong press on M easure HR on your watch. You can release your finger as soon as you see “loading...” along with a small vibration. Your BPM will show after a few seconds.
Track your Activity By default, your watch tracks your activity such as steps you take and estimate distance based on the personal information you enter such as step length. You can also track specific sports: Walking, Running, Cycling, Skipping (Jumping Rope), Badminton, Basketball, Football (Soccer).
Weather To enable weather on your watch, open the Da Fit app on your smartphone, tap on the watch icon , select O thers , then turn on W eather . Make sure to grant the app access to your location.
Text Messages You can read your messages (SMS, etc.) from your watch. Just l ong press on Messages , then q uick tap to navigate among messages. Note : Your watch will display the last couple of text messages. New incoming messages will replace older ones.
Notifications In addition to incoming messages, your watch can notify you every time you receive a phone call, and other notifications on your smartphone such as iMessage, Whatsapp, Facebook, Messenger, Twitter, Instagram, Skype, etc. To control which notification to receive on your watch, open the Da Fit app on your smartphone, tap on the ...
Find Device To help you locate your watch, you can generate a long vibration from your smartphone. To do so, open the Da Fit app on your smartphone, tap on the w atch icon , select Others , then F ind Device . Note...
Music Remote You can control your smartphone’s music remotely from your watch. To play, pause and change tracks remotely, l ong press on P layer on your watch.
Camera Remote You can control your smartphone’s camera to take photos remotely from your watch. To take photos remotely, open the camera app on your smartphone, l ong press on Shutter on your watch.
Troubleshooting Watch lost connection with the Da Fit app If your watch lost connection with your smartphone, follow these steps: ● Make sure your watch is fully charged ● Open the Da Fit app on your smartphone ● Select the w atch icon ●...
Unable to pair with phone If you are unable to pair your watch with your smartphone, follow these steps: ● Make sure your watch is fully charged ● Open your Settings in your smartphone, select Bluetooth, then your watch. Select “forget this device”. ●...
To turn off your watch, l ong press in the main screen (where you see the time). You will see a battery level along with some serial numbers. From that screen, l ong press one more time. You will see 3 options: P ower Off , R eset and C ancel . L ong press on Power Off...
Need help?
Do you have a question about the 2019 Smartwatch and is the answer not in the manual?
Questions and answers
How the hell do update time for daylight saving ?
The time on the Spade & Co 2019 Smartwatch syncs automatically with your smartphone when connected via the Da Fit app. To update the time for daylight saving, ensure your smartphone's time is correct and that the smartwatch is connected to the Da Fit app. The time will update automatically.
This answer is automatically generated
my smart watch will not charge; it is down to 6 percent but just goes between main screen and percent of charge. I have had the charge cord on overnight and no rise, still flashes 6 %. What do I do? I have had my smart watch for about two years now.
If your Spade & Co 2019 Smartwatch will not charge and remains at 6 percent, do the following:
1. Make sure the charger is connected to a USB or power outlet.
2. Check that the charger is positioned correctly, with the two connectors aligned with the watch connectors on the back.
3. Ensure the charger pins are properly placed.
4. Look for the charging animation on the watch screen to confirm it is charging.
If the issue continues, try a different USB port or charging adaptor.
This answer is automatically generated
How to sync smartwatch 3 with my andrroid phone?
To sync the Spade & Co 2019 Smartwatch with an Android phone:
1. Fully charge the watch.
2. Install the Da Fit app on your Android phone.
3. Open your phone’s Bluetooth settings and select your watch. If it's already paired, choose “forget this device.”
4. Kill the Da Fit app or reboot your phone.
5. Relaunch the Da Fit app.
6. Tap the watch icon and select “Connect Device.”
7. Follow the on-screen instructions under "Getting Started."
This answer is automatically generated
Need to turn off alarm T
@Gayle Momserrate Says UK/CA
Need to turn off alarm
To turn off the alarm on the Spade & Co 2019 Smartwatch, open the Da Fit app on your smartphone, tap on the watch icon, select Alarms, then tap on the alarm you want to turn off and adjust or delete it.
This answer is automatically generated
1) I enabled red dot for my notifications. Has never shown on the face of the watch. 2) My watch vibrates when I get a text but not consistently. 3) Have to go into the app, tap on notifications and disable most of the social media apps that are turned on. Clicked on SAVE, yet the very next day, the apps are turned back on.
To manage notifications on your Spade & Co 2019 Smartwatch, open the Da Fit app on your smartphone, tap on the watch icon, and select Notifications. From there, you can turn notifications on or off for specific apps. If you experience inconsistent vibration for texts, ensure notifications are enabled for messaging apps in the Da Fit app. If social media app settings persist, toggle the notification settings off and on again in the Da Fit app to refresh them.
This answer is automatically generated
I’m trying to get my watch to change to daylight savings time but I can’t get the app to find my watch. I have turned off my phone, turned off and back on Bluetooth, deleted the da fit app, reinstalled it, numerous times, still will not connect! This is ridiculous!! Help!
To connect your Spade & Co 2019 Smartwatch to the Da Fit app, follow these steps:
1. Ensure Bluetooth is turned on on your smartphone.
2. Install and open the Da Fit app on your smartphone.
3. Tap on the watch icon and select your smartwatch (typically "SN60-Plus") to connect it.
4. Once connected, the time on your smartwatch will automatically sync with your phone.
To adjust for daylight savings time, ensure your smartphone's time settings are updated, as the smartwatch syncs time from the phone.
This answer is automatically generated
The Smart watch I purchased on Dec. 30, 2023 was beeping the whole time I charged it recently. After it was charged it was not connected to my phone. I reset the watch and connected it to my phone. It was working well. I just tried turning it on and all I get is a lighted blank screen.
If your Spade & Co 2019 Smartwatch has a blank screen after charging, long press the home button at the bottom of the screen for a few seconds. If the screen does not turn on, ensure the watch is properly charged using the provided USB charger. If the issue persists, email support@spadeandco.com for further assistance.
This answer is automatically generated
My watch is dead and won’t charge
If your Spade & Co 2019 Smartwatch won't charge, it might be due to the following reasons:
1. The watch could be out of power.
2. The USB charger provided might not be properly connected or functional.
Make sure to use the USB charger that came with the watch and ensure it's securely connected. If the issue persists, refer to other troubleshooting steps or contact support.
This answer is automatically generated
How do you delete messages? When I do select delete, it doesn’t delete