deltalight RGBW DRIVER Installation Instruction

Advertisement

170
2 groups DMX512
signal input & output
Beschermd tegen vaste voorwerpen die groter zijn dan 12 mm
Protégé contre les objets solides de plus de 12 mm
Geschützt gegen Festkörper größer als 12 mm
Protected against solid objects greater than 12 mm
Protegido contra objetos sólidos superiores a 12 mm
Protetto contro oggetti solidi più grandi di 12 mm

1 Product Data

• DMX512 RDM decoder, RDM function can realize intercommunication between DMX master and decoder.
for example, you can set DMX decoder's address by DMX master console.
• Total 5 PWM output channels, common anode. DMX channel quantity from 1CH~5CH settable
• PWM output resolution ratio 8bit , 16bit settable.
• Output PWM frequency from 500HZ ~ 30K HZ settable.
• Output dimming curve gamma value from 0.1 ~ 9.9 settable.
• Decoding mode settable.
• Galvanic isolation
2 Safety & Warnings
• DO NOT install with power applied to device.
• DO NOT expose the device to moisture.
Ref: 21032 0010
29
59
RGBW DRIVER
A
+
B
DC POWER INPUT
Commong Anode Output (+)
CH 1: R output (-)
CH 2: G output (-)
CH 3: B output (-)
CH 4: W/WW output (-)
CH 5: W/CW output (-)
Enkel geschikt voor toestellen op zeer lage spanning (minder dan 50 V-AC / 120 V-DC)
Convient uniquement pour les produits à très basse tension (moins de 50 V-AC / 120 V-DC)
Geeignet für Güter mit sehr niedriger Spannung (unter 50 V-AC / 120 V-DC)
Only suited for goods at very low voltage (below 50 V-AC / 120 V-DC)
Se recomieda únicamente para aquellos productos de tensión muy baja (menos de 50 V-AC / 120 V-DC)
Vale unicamente per i prodotti a tensione molto bassa (inferiore a 50 V-AC / 120 V-DC)
1
Last Update ALLU 17/04/2019

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the RGBW DRIVER and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for deltalight RGBW DRIVER

  • Page 1 Installation Instruction RGBW DRIVER DC POWER INPUT Commong Anode Output (+) CH 1: R output (-) CH 2: G output (-) CH 3: B output (-) CH 4: W/WW output (-) CH 5: W/CW output (-) 2 groups DMX512 signal input & output...
  • Page 2 Installation Instruction 3 Operation Up, Down button is for menu selection.After power on the decoder, if keep on clicking Up button, you will find below menu on display: DMX signal indicator :: When DMX signal input is detected, the indicator on the display following after turns on red X X X .
  • Page 3 Installation Instruction 5 Operation By holding button Back + Enter together at the same time over 5 seconds until the display go off, it will restore default settings . 1. DMX address setting: select menu XXX, click button “Enter”, display flashes,then click or hold button “Up” / “Down” to set DMX address (click is slow, hold is fast.), then click button“Back”...
  • Page 4 Installation Instruction 5 Operation DMX address is 001, CH03 DMX Console Slider number dp 1.1 dp 2.1 dp 4.3 dp 5.3 DMX channel for output 1 dimming for output 1 dimming for output 1 dimming for output 1 dimming for output 2 dimming for output 1 micro dimming for output 2 dimming for output 2 dimming...
  • Page 5 Installation Instruction 5 Operation The data definitions for strobe channel are as follows: {0, 7},//undefined {8, 65},//slow strobe-->fast strobe {66, 71},//undefined {72, 127},//slow push fast close {128, 133},//undefined {134, 189},//slow close fast push {190, 195},//undefined {196, 250},//random strobe {251, 255},//undefined Restore to Factory Default Setting Press and hold down both “...

Table of Contents